• Journal of Institute of Convergence Technology
• /
• v.2 no.2
• /
• pp.20-24
• /
• 2012

In this paper, we perform a ANSYS simulation of assembly structure composed of three parts, bolt, nut, and coil spring, under the loading of a screw torque 640~800 ($N{\cdot}m$) derived from the given bolt tensile strength 10.9, which allows us to investigate a lock-nut mechanism for the prevention of bolt-loosening after three parts are fastened. And also we investigate the safety factor of each component with effective stress distribution obtained from the simulation, which enables us to estimate the structural safety of a new lock-nut structure. Both simulation and investigation shown in this paper will contribute to the development of a new lock nut structure.

• Korean Journal of Plant Resources
• /
• v.20 no.1
• /
• pp.63-68
• /
• 2007

The purpose of this study was to applicate fundamental data for breeding new cultivar through selection of superior individuals and to investigate its nut characteristics in walnut hybrids. Selection of superior individuals with good nut qualities including high nut weight (NWT, >13g) and percentage of weight relative to total weight of nut (PWR, >50%) was carried out and then 4 promising individuals ($Sansung 4{\times}Concord-8,\;Concord{\times}Sansungl,\;Concord{\times}Sansung4\;and\;McKinster{\times}Punghan1$) were selected by quantitative characters. Especially width of pad of suture was main factor in selection of nut with high PWR (percentage of weight relative to total weight of nut) In addition, kernel length showed high correlation with kernel and nut weight. Thickness of septem (TOP) also had an effect on ease of kernel removal (EKR). In qualitative characters, there is a great difference among the individuals and cross combinations as well as showed simultaneously various characteristics in the same individual.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.15 no.3
• /
• pp.72-78
• /
• 2016

In this study, we analyzed the accidental hydrogen embrittlement affecting the track nut on a self-propelled howitzer. Tracks are key components to maintain a high degree of confidence in the operation of the self-propelled howitzer and the safety of the crew. This study analyzed the fractured surface using SEM to review accidental damage of the wedge nut. In addition, we conducted revival tests and analyzed the results to identify the cause of the wedge nut damage from hydrogen embrittlement. We should carry out factor analysis and continuous improvement of the manufacturing process to determine the accidental breakage mechanism for future enhancement of the self-propelled howitzer. This study will be the useful reference for enhancing process designs in similar products.

• The Korean Journal of Ecology
• /
• v.24 no.6
• /
• pp.377-380
• /
• 2001

Herbivory is an important selective forces on plants by reducing the ability of the plant to compete with its neighbors and to produce offspring. Oak nut weevil(Mechoris ursulus Roelofs) females lay eggs in unmatured acorns and cut off the branch of oviposited acorns. To investigate the influences of branch-cutting behavior of oak nut weevils on oak production, we surveyed the horizontal and vertical distribution ranges of damaged oaks and depth of sites of overwintering larvae and quantified the amounts of biomass and acorn removed by the weevils on deciduous oak species. All of the endemic oak species in Korea were damaged by oak nut weevils in all of the study sites including Mt. Halla and Mt. Seorak. The upper limit of vertical distribution of damaged oaks by the weevils raried from 700 m to 900 m. Mostly their larvae were found in soil from 8.1 cm to 10.0 cm depth in winter. Percentage of annual net primary productivity($720g{\cdot}m^{-2}{\cdot}day^{-1}$) of oak species removed by the weevils was about 7%, which is higher than the percentage removed by all the herbivores in typical temperate forest(5%) and equivalent to that by all the herbivores in tropical forest. The predation percentage of annual acorn production by oak nut weevil was 27% in Q. mongolica and 33% in Q. acutissima. This results indicate that the branch-cutting behavior of oak nut weevil may be the most important factor regulating oak population and affecting other predators dependent on acorns.

• Nuclear Engineering and Technology
• /
• v.55 no.8
• /
• pp.2905-2918
• /
• 2023

The valve assembly used in nuclear power plants is important safety-related equipment. In the new standard, the physical attributes are measured using a valve diagnosis test, which is used in the expansion to other non-tested valves using a quantitative test-basis methodology. With a motor-operated actuator, the state of stem's lubrication is related to physical attributes such as the stem factor and the friction coefficient. This study analyzed the numerical transient of fluid and solid lubrication with a squeeze film effect due to the loading rate on the stem and the stem nut using the experimental data. The differential equation that governs the motion mechanism of the stem and stem nut is established and analyzed. The flow rate, the fluid and the solid contact forces are calculated with the friction coefficient. Finally, we found that a change in the friction coefficient results from a change of the shear force in the solid contact mode during the interchange process between the solid contact mode and the fluid contact mode. The qualitative understanding of the squeeze film effect is expanded quantitatively for forces, thread surface distance, velocity, and acceleration, with consideration of the metal solid contact and fluid contact.

• Journal of the Korean institute of surface engineering
• /
• v.44 no.1
• /
• pp.21-25
• /
• 2011

This test focuses on the correlation between the lubrication, ductility and strength through the change of nut lubricant which decides joining angle for A490 bolt sets required in the AASHTO (American Association of State Highway & Transportation Officials). Because the lubrication of high tension bolt, nut, washer sets becomes an important factor to ductility and joining load, the quality improvement is required for improving reliability and securing enough lubrication of maker and user. This study examines the quality characteristics required in the specification through tests because only this standard specifies joining quality in the extreme conditions (as much about two times of the joining angle on site as normal condition). Moreover, this study is limited to the test on joining axial force required in the AASHTO for the three nut lubrication conditions of A490 bolt set. It is concluded that the nuts should be coated or waxed enough for the improvement of the joining axial force and ductility of bolts required in the standards. It is shown that in the case of plain high tension bolt sets, a rust preventing lubricative oil shall be applied and the torque coefficient value for A490 bolt sets should be maintained below 0.175.

• Nuclear Engineering and Technology
• /
• v.35 no.2
• /
• pp.133-143
• /
• 2003

Stem-stem nut coefficient of friction(COF) in motor-operated gate/globe valves is one of the important factors which determine the performance of the valve/actuators. The COF is affected greatly by the type and condition of the stem-stem nut lubricants, environmental parameters, surface condition of the stem/stem-nuts, and the number of strokes after the lubrication. In this paper, the measured data of the COFs at stem threads of some safety-related motor-operated gate/globe valves in domestic nuclear power plants are presented. In addition, the performance of the lubricants is evaluated by comparing the COFs among those valves. The results show that the measured COF at torque switch trip are higher than the unwedging COF and conservatively applicable to the unwedging COF. It is also shown that the lubricating performance based on the measured COFs varies with the lubricants.

• Asian Pacific Journal of Cancer Prevention
• /
• v.17 no.7
• /
• pp.3335-3340
• /
• 2016

Background: Oral submucous fibrosis (OSF) is a precancerous condition with a 4 to13% malignant transformation rate. Related to the habit of areca nut chewing it is mainly prevalent in South-east Asian countries where the habit of betel quid chewing is frequently practised. On chewing, alkaloids and polyphenols are released which undergo nitrosation and give rise to N-nitrosamines which are cytotoxic agents. CYP450 is a microsomal enzyme group which metabolizes various endogenous and exogenous chemicals including those released by areca nut chewing. CYP1A1 plays a central role in metabolic activation of these xenobiotics, whereas CYP2E1 metabolizes nitrosamines and tannins. Polymorphisms in genes that code for these enzymes may alter their expression or function and may therefore affect an individuals susceptibility regarding OSF and oral cancer. The present study was therefore undertaken to investigate the association of polymorphisms in CYP1A1 m2 and CYP2E1 (RsaI/PstI) sites with risk of OSF among areca nut chewers in the Northern India population. A total of 95 histopathologically confirmed cases of OSF with history of areca nut chewing not less than 1 year and 80, age and sex matched controls without any clinical signs and symptoms of OSF with areca nut chewing habit not less than 1 year were enrolled. DNA was extracted from peripheral blood samples and polymorphisms were analyzed by PCR-RFLP method. Gene polymorphism of CYP1A1 at NcoI site was observed to be significantly higher (p = 0.016) in cases of OSF when compared to controls. Association of CYP1A1 gene polymorphism at NcoI site and the risk of OSF (Odd's Ratio = 2.275) was also observed to be significant. However, no such association was observed for the CYP2E1 gene polymorphism (Odd's Ratio = 0.815). Our results suggest that the CYP1A1 gene polymorphism at the NcoI site confers an increased risk for OSF.

• The KSFM Journal of Fluid Machinery
• /
• v.8 no.1 s.28
• /
• pp.16-22
• /
• 2005

This paper presents the method of ROL(Rate Of Loading) improvement for the Motor Operated Gate Valve operated in high differential pressure condition. ROL is one of the most important evaluation parameters for the valve ability. It is close to correlation in stem factor (SF) and appears different value by the differential pressure of fluid. ROL and SF are analyzed by the static test and dynamic test. The obtained result show that the modification of stem factor is very important factor for the ROL improvement. In order to obtain the same value of SF between static and dynamic test, stem and stem nut should be combined appropriately by the repetition test.

• 유체기계공업학회:학술대회논문집
• /
• 2003.12a
• /
• pp.562-567
• /
• 2003

This paper presents the method of Rate of Loading(ROL) improvement for the Motor Operated Gate Valve operating in high differential pressure condition. The character of ROL and Stem Factor is analyzed. Static test and dynamic test were performed and acquired the diagnosis signal for the valve closing stroke. The result of this study is the modification of stem factor is very important factor for the ROL improvement. In order to obtain the same value of dynamic test thread friction coefficient stem and stem nut should be combined appropriately.