• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.4
• /
• pp.72-79
• /
• 1994

In an automotive spark ignition, it is important to form the proper mixture(air/fuel) on each driving condition for developing the stabilizing combustion and exhaust characteristics. Since most of supply fuel is attached on the inside wall of the intake manifold for unadequate atomization by fuel injection system, it brings a bad effect on combustion and exhaust caused by nonuniformity of fuel distribution to each cylinder and mixture variation. Also it affects engine performance variation and causes noises and vibration. In this study, we verified the effect of the mixture variation which is caused by fuel liquid film in an intake manifold on combustion characteristics and engine performance.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.1
• /
• pp.120-128
• /
• 1997

The variations of the temperature field in a passenger compartment were measured by using a HSI true color image processing system and TLC(Thermochromic Liquid Crystal) solution. This temperature measurement technique was proved to be useful for analyzing the ventilation flow. The flow field in the passenger compartment was visualized using a particle streak method with pulsed laser light sheet. The temperature field and flow field in the passenger copartment were affected significantly by the ventilation mode. The panel-vent mode heating had shorter elapse time to reach a uniform temperature than the foot-vent mode under the same ventilation condition and nonuniformity inside the passenger compartment could be minimized effectively by using the bilevel heating mode. The temperature increase rate in the rear passenger compartment was iower than the front compartment, especially in the vicinity of the rear seat occupants' knee level.

• Journal of the Korea Society of Computer and Information
• /
• v.22 no.7
• /
• pp.39-45
• /
• 2017

In this paper, we propose three compensation methods to solve problems in high-resolution airborne infrared camera and to improve long-range target information acquisition performance. First, image motion and temporal noise reduction technique which is caused by atmospheric turbulence. Second, thermal blurring image correction technique by imperfect performance of NUC(Non Uniformity Correction) or raising the internal temperature of the camera. Finally, DRC(Dynamic Range Compression) and flicker removing technique of 14bits HDR(High Dynamic Range) infrared image. Through this study, we designed techniques to improve the acquisition performance of long-range target information of high-resolution airborne infrared camera, and compared and analyzed the performance improvement result with implemented images.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.35 no.4
• /
• pp.1-9
• /
• 2012

Decisions on reliability screening rules and burn-in policies are determined based on the estimated reliability. The variability in a semiconductor manufacturing process does not only causes quality problems but it also makes reliability estimation more complicated. This study investigates the nonuniformity characteristics of integrated circuit reliability according to defect density distribution within a wafer and between wafers then develops optimal burn-in policy based on the estimated reliability. New reliability estimation model based on yield information is developed using a spatial stochastic process. Spatial defect density variation is reflected in the reliability estimation, and the defect densities of each die location are considered as input variables of the burn-in optimization. Reliability screening and optimal burn-in policy subject to the burn-in cost minimization is examined, and numerical experiments are conducted.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.13 no.10
• /
• pp.1017-1024
• /
• 2001

The optimum shape of header part in a PFHE (parallel-flow heat exchanger) is studied. The optimal values of each geometric parameter are proposed according to their order of influence with varying the four important parameters (the injection angle of working fluid ($\Theta$), the shape of inlet(S), the location of inlet ($y_c/D_{in}$) and the height of the protruding flat tube ( $y_{b/}$ $D_{in}$ )). The optimal geometric parameters are as follows:$\Theta= -21^{\circ}C,\; S=Type\; A \;an\;y_b/D_{in}$/=0. The heat transfer rate of the optimum model, compared to that of the reference model, is increased by about 55%. The optimal geometric parameters ran be applicable to the Reynolds number ranging from 5,000 to 20,000.0.

• Ocean and Polar Research
• /
• v.23 no.1
• /
• pp.35-49
• /
• 2001

An ichthyofauna analysis of the East Sea using quantitative investigation procedures for latitudinal variations of the species richness and clustering of the species list is presented to illustrate the application of the adopted geographical scaling (less than 1:10,000,000) which provides a principal opportunity for common benthic and pelagic biogeographical zonation. The distribution of both pelagic and benthic marine fish biota at a scale of biosphere (or its major sections) was highly influenced by spatial nonuniformity of hydrological structure associated with the various water circulations and frontal zones. Following zoogeographical zonations were established for the East Sea: Osaka, East Korea, Primorye, North Primorye, Northern East Sea, Uetsu, Tsugaru, Soya and West Sakhalin.

• Journal of the Korean Vacuum Society
• /
• v.8 no.2
• /
• pp.172-179
• /
• 1999

The axial distributions of plasma density in a helical resonator plasma with the external magnetic field have been measured using Langmuir probes. Net RF power is set to 200W and chamber pressure is varied from 0.4 mTorr to 100mTorr there are three kinds of eternal magnetic field structure applied on the helical resonator plasma. One is a uniform magnetic field, the second is a positive gradient magnetic field and the third is a negative gradient magnetic field. In the three magnetic field structures, the negative gradient magnetic field is found to show the highest increase in plasma density on the substrate compared with other magnetic structures. Plasma density profile in helical resonator is well consistent with electromagnetic field pattern obtained by computer simulation. It is also found that axial magnetic fields do not affect plasma density distribution in the plasma reactor region, but induce the increase of plasma density in the process chamber region. In order to avoid the nonuniformity of radial density profile, weak magnetic fields under 100G are applied.

• Water Engineering Research
• /
• v.3 no.3
• /
• pp.177-193
• /
• 2002

Experiments were conducted in an initially straight laboratory alluvial channel to investigate channel meandering characteristics. The experimental observations revealed an empirical relation between three types of tortuosity ratios used for describing meandering characteristics. Furthermore, the Strauhal number was found to be higher for bed material with greater resistance to erosion than with lower resistance to erosion. The meandering characteristics were also investigated using the concept of buckling employed in solid mechanics and the concept of siphoning of fluid mechanics. The buckling of flow, attributable to the flow nonuniformity across the channel cross-section, was found to follow the same pattern as did meandering observed experimentally. The processes of expansion of meanders and cut-off can be explained using the concept of siphoning. The results of expanding meander planforms observed in four experimental tests supported the viability of these concepts.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.9 no.2 s.25
• /
• pp.111-117
• /
• 2006

This paper describes the design principles and methods of electronic processor for thermal imager with 320$\times$240 staring array infrared detector. For the detector's nonuniformity correction and excellent image quality, we have designed the multi-point correction method using the defocusing technique of the optics. And to enhance the image of low contrast and improve the detection capability, the new technique of histogram processing has been designed. Through these image processing techniques, we have developed the high quality thermal imager and acquired a satisfactory thermal image. The result of MRTD(Minimum Resolvable Temperature Difference) is $0.1^{\circ}C$ at 4cycles/mard.

• Journal of Surface Science and Engineering
• /
• v.27 no.4
• /
• pp.223-233
• /
• 1994

It is well known that compositionally modulated Cu-Ni alloy can be produced by an electrochemical method in Ni sulfate solution containing trace amount of Cu. a mathematical model is presented to describe the current distribution and weight percent of Cu in Ni layer on the rotating disk electrode. The model includes convective-diffusion equation, the Laplace's equation and various overpotentials, and is solved numerically. The thickness of Cu layer is almost uniform whereas the thickness of Ni layer as well as the Ni/Cu weight ratio are increased approaching to the edge of the disk. These results agree well with the experimental values. The ohmic potential drop is suggested as a major cause of a nonuniformity in Ni layer. The optimum plating condition for the fabrication of susperlattice is proposed based on the results of this study.