• Korean Journal of Materials Research
• /
• v.30 no.4
• /
• pp.169-175
• /
• 2020

Silicon nitride thin films are deposited by RF (13.57 MHz) magnetron sputtering process using a Si (99.999 %) target and with different ratios of Ar/N₂ sputtering gas mixture. Corning G type glass is used as substrate. The vacuum atmosphere, RF source power, deposit time and temperature of substrate of the sputtering process are maintained consistently at 2 ~ 3 × 10^-3 torr, 30 sccm, 100 watt, 20 min. and room temperature, respectively. Cross sectional views and surface morphology of the deposited thin films are observed by field emission scanning electron microscope, atomic force microscope and X-ray photoelectron spectroscopy. The hardness values are determined by nano-indentation measurement. The thickness of the deposited films is approximately within the range of 88 nm ~ 200 nm. As the amount of N₂ gas in the Ar:N₂ gas mixture increases, the thickness of the films decreases. AFM observation reveals that film deposited at high Ar:N₂ gas ratio and large amount of N₂ gas has a very irregular surface morphology, even though it has a low RMS value. The hardness value of the deposited films made with ratio of Ar:N₂=9:1 display the highest value. The XPS spectrum indicates that the deposited film is assigned to non-stoichiometric silicon nitride and the transmittance of the glass with deposited SiO₂-Si_xN_y thin film is satisfactory at 97 %.

• Journal of Hydrogen and New Energy
• /
• v.7 no.2
• /
• pp.157-164
• /
• 1996

The AB5-type metal hydride electrodes using $(LM)Ni_{4.49}Co_{0.1}Mn_{0.205}Al_{0.205}$(LM : Lanthaniumrich Mischmetal) alloy powders(${\leq}200$mesh) which were coated with 25wt% copper in an acidic bath were prepared with or without addition of 10wt% PTFE as a binder. Prior to electrochemical measurements, the electrodes were sintered at $40^{\circ}C$ for 1 and 2hrs in vacuum with Mm(mischmetal) and sponge type Ti getters. The properties such as maximum capacity, cycle life and mechanical strength of the negative electrode have been investigated. The surface analysis of the electrode was also obtained before and after charge-discharge cycling using scanning electron microscope(SEM). From the observations of electrochemical behavior, it was found that the sintered electrode shows a lower maximum discharge capacity compared with non-sintered electrode but it shows a better cycle life. For the both electrodes with or without addition of PTFE binder, the values of mechanical strength were obtained, and their values increased with increasing sintering time. However, there is little difference of discharge capacity for both electrodes.

• Composites Research
• /
• v.15 no.6
• /
• pp.1-7
• /
• 2002

In VARTM process where a sacrificial medium is used to facilitate the resin flow, the velocity of resin varies drastically between the sacrificial medium and the fiber preform. Although the thickness-to-length ratio of a VARTM product is usually small, a 3-D analysis is prerequisite to analyze the lead-lag flow in the two different media. The problem associated with the full 3-D analysis is the CPU time. A full 3-D numerical mesh comprising large number of nodes requires an impractical CPU time on average computer platforms. In this study, a dual-scale analysis technique was developed. The flow analysis for the entire calculation domain was conducted in 2.5-D, and the 3-D analysis was performed for a small area of special concern. In some numerical examples, the local 3-D analysis could discover an eccentric flow pattern as well as the lead-lag flow that will inevitably be neglected in 2.5-D simulations. The global-local analysis technique practiced in this study can be used to analyze the intricate flow of resin through non-uniform media in affordable CPU times.

• The Korean Journal of Food And Nutrition
• /
• v.22 no.1
• /
• pp.20-28
• /
• 2009

According to traditional oriental medicine, only non-coagulated native deer blood is said to be effective, and coagulated deer blood is ineffective. Thus, a drying and tablet-producing method for deer blood was developed to maintain its physiological and therapeutic activity, and so that after drying, it can be redissolved and protected from coagulation. Proteases such as trypsin, pepsin, chymotrypsin, and aminopeptidase were added to the deer blood indicating that it coagulated in an hour, as shown by the reference. Wax gourd extract, which is high in protease, was added to the blood resulting in anticoagulation for 31 hours. Also, additions of 1% EDTA, 0.38% sodium citrate, 0.16% calcium oxalate, 1.2% ethanol, and 0.006% heparin to the deer blood resulted in anticoagulation for 1 hour, 4 hours, 2 hours, 1 hour, and 31 hours, respectively. In an experiment using 0.19% sodium citrate plus 1% wax gourd extract, and 0.006% heparin plus 1% wax gourd extract, anticoagulation was maintained for up to 72 hours. However, since heparin can not be used in food, the deer blood tablet was made with the addition of 0.19% sodium citrate and 1% wax gourd extract, followed by freeze drying. The dissolution rate for the tablet manufactured in this manner was 96.7%. And the dissolution rates for spray-dried deer blood, vacuum-dried deer blood, and marketed deer blood tablets were 85%, 81%, and 25.5%, respectively. The composition of the tablet produced from the freeze-dried deer blood was 56.4% protein, 18.7% lactose, 1.2% amino acids, 1.0% glucose, 0.7% lipids, 180 mg/100 g of iron, 13 mg/100 g of potassium, 39.1 mg/100 g of calcium, 480 mg/100 g of sodium, 368 mg/100 g of chloride, each.

• Food Science of Animal Resources
• /
• v.34 no.4
• /
• pp.464-471
• /
• 2014

Ground lean pork was irradiated by an electron beam or X-rays to compare the effects of two types of radiation generated by a linear accelerator on the quality of Bologna sausage as a model meat product. Raw ground lean pork was vacuum packaged at a thickness of 1.5 cm and irradiated at doses of 2, 4, 6, 8, or 10 kGy by an electron beam (2.5 MeV) or X-rays (5 MeV). Solubility of myofibrillar proteins, bacterial counts, and thiobarbituric acid reactive substance (TBARS) values were determined for raw meat samples. Bologna sausage was manufactured using the irradiated lean pork, and total bacterial counts, TBARS values, and quality properties (color differences, cooking yield, texture, and palatability) were determined. Irradiation increased the solubility of myofibrillar proteins in a dose-dependent manner (p<0.05). Bacterial contamination of the raw meat was reduced as the absorbed dose increased, and the reduction was the same for both radiation types. Differences were observed only between irradiated and non-irradiated samples (p<0.05). X-ray irradiation may serve as an alternative to gamma irradiation and electron beam irradiation.

• Journal of the Semiconductor & Display Technology
• /
• v.9 no.1
• /
• pp.41-47
• /
• 2010

The effects of thermal treatment on CNTs, which were coated with a-$CN_x$ thin film, were investigated and related to variations of chemical bonding and morphologies of CNTs and also properties of field emission induced by thermal treatment. CNTs were directly grown on nano-sized conical-type tungsten tips via the inductively coupled plasma-chemical vapor deposition (ICP-CVD) system, and a-$CN_x$ films were coated on the CNTs using an RF magnetron sputtering system. Thermal treatment on a-$CN_x$ coated CNT-emitters was performed using a rapid thermal annealing (RTA) system by varying temperature ($300-700^{\circ}C$). Morphologies and microstructures of a-$CN_x$/CNTs hetero-structured emitters were analyzed by FESEM and HRTEM. Chemical composition and atomic bonding structures were analyzed by EDX, Raman spectroscopy, and XPS. The field emission properties of the a-$CN_x$/CNTs hetero-structured emitters were measured using a high vacuum (below $10^{-7}$ Torr) field-emission measurement system. For characterization of emission stability, the fluctuation and degradation of the emission current were monitored in terms of operation time. The results were compared with a-$CN_x$ coated CNT-emitters that were not thermally heated as well as with the conventional non-coated CNT-emitters.

• Tribology and Lubricants
• /
• v.15 no.1
• /
• pp.77-82
• /
• 1999

The processing conditions fur the synthesis of platelet W $S_2$ lubricant powder through a solid-gas reaction were optimized. The mixture of tungsten and sulfur powders were sealed in a vacuum of 10$^{-6}$ torr, prior to heat-treating at 85$0^{\circ}C$ fur 8 days. The reaction product showed a well-developed platelet W $S_2$ powder with an average size of 3.8 ${\mu}{\textrm}{m}$. The TGA/DTA analysis of the synthesized W $S_2$ powder was performed up to 120$0^{\circ}C$ at a rate of 1$0^{\circ}C$/min in flowing air (100 ${\mu}{\textrm}{m}$/min) atmosphere. The weight loss was about 6% up to 120$0^{\circ}C$ compared to the original weight. A rapid weight loss of about 5% occurred in the temperature range of 44$0^{\circ}C$ to 66$0^{\circ}C$ and an exothermic peak observed due to the transition of W $S_2$ to W $O_3$. The synthesized W $S_2$powder was coated on the commercial deep grooved ball bearing (No. 6203) to examine the effect of W $S_2$, coating layer on the noise and endurance of the ball bearing. The level of noise obtained from W $S_2$, coated-ball bearing (56 ㏈) was higher. than the value (32 ㏈) occurred in the case of greece lubrication. The endurance of the ball-bearing assembled after the coating of W $S_2$ powder onto each part increased 50 times compared to the non-coated ball-bearing..

• Journal of Welding and Joining
• /
• v.31 no.3
• /
• pp.76-83
• /
• 2013

This study investigated the effect of bonding temperature and holding time on microstructures and mechanical properties of diffusion bonded joint of Haynes230. The diffusion bonds were performed at the temperature of 950, 1050, and $1150^{\circ}C$ for holding times of 30, 60, 120 and 240 minutes at a pressure of 4MPa under high vacuum condition. The amount of non-bonded area and void observed in the bonded interface decreased with increasing bonding temperature and holding time. Cr-rich precipitates at the linear interface region restrained grain migration at $950^{\circ}C$ and $1050^{\circ}C$. However, the grain migration was observed in spite of short holding time due to the dissolution of precipitates to base metal in the interface region at $1150^{\circ}C$. Three types of the fracture surface were observed after tensile test. The region where the coalesce and migration of grain occurred much showed high fracture load because of base metal fracture whereas the region where those did less due to the precipitates demonstrated low fracture load because of interface fracture. The expected fracture load could be derived with the value of fracture area of base metal ($A_{BF}$) and interface ($A_{IF}$), $Load=201A_{BF}+153A_{IF}$. Based on this equation, strength of base metal and interface fracture were calculated as 201MPa and 153MPa, respectively.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.2 no.3
• /
• pp.211-217
• /
• 2004

A Li recovery technology has been developed and related experimental verification efforts were carried out to improve the economical viability and environmental friendliness of the 'Advanced Spent Fuel Conditioning Process' being developed at KAERI. This technology is characterized by the combination of 1) the electrolysis of $Li_2O$ in a molten salt by using a porous non-conducting magnesia container at the cathode, 2) the separation of the Li in the container from the molten salt by elevating the container above the level of a molten salt, 3) the transport of the Li in the container by using a vacuum siphon to a separated reservoir. Li was semi-continuously recovered from a LiCl-$Li_2O$ molten salt with a more than 95% yield by using the developed technology.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.8
• /
• pp.767-773
• /
• 2010

This paper describes development of a non-explosive separation device which can be equipped on small satellites. The spur geared micro DC motor, which has high reliability and advantage of price, is adopted as an actuator. The proposed separation device has resettability and it does not need extra jig to reload. In addition, the simple structure makes it easy to fabricate and assemble. To verify the performance of the proposed device, the response time tests, maximum preload tests and maximum shock level tests were performed. Also, through the vibration tests and thermal vacuum tests, feasibility of the proposed separation device was shown in launching and space environments. Therefore, we expect that the proposed separation device can replace the imported separation devices in near future.