• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.1538-1541
• /
• 2005

For reliability evaluation of AC-PDP, one of the most important factor is sealing property. In this paper, the reliability evaluation test method of the commercialized sealing glass frit in AC-PDP was studied. 6 inch AC-PDP panels were tested for evaluation of sealing glass frit by vibration shock test, thermal shock test, non -destructive X-ray inspection, residual stress inspection and residual gas detection. These test methods are proposed as a standard for testing the reliability of sealing glass frit. The main failure mode of sealing glass frit in AC-PDP seems to be the crack propagation from thermal cycling rather than mechanical factor.

• International Journal of Railway
• /
• v.5 no.1
• /
• pp.22-28
• /
• 2012

This report is devoted to the problems of Mongolian Railway Transportation Safety such as high length of wagon service life, defects due to the more factors of exploitation, idle time, increase of faults, poor condition of repairing shops and more hand and mechanical operations and these conditions are quite difficult to meet the safety and reliability of increasing transportation from day to day. The paper discusses that the most optimum solution is diagnosing before occurring wear, breakdown, and defects on the basis of studying characteristics of structural material breakdown, residual methods of voltage, effects of material hardness and linear defects of a crystal net and the reform of machines is very important to implement it. It focuses the structures, characteristics of the material transportation and tests and analyses of the wagon cart which has to meet the traffic safety of wagons and slow and soft movement. The study is done on the wagon chassis which has to meet the traffic safety of luggage wagons.

• Journal of Institute of Control, Robotics and Systems
• /
• v.4 no.4
• /
• pp.420-426
• /
• 1998

It is the purpose of this paper to make a preliminary study on the use of repetitive control to improve velocity accuracy by eliminating repetitive disturbances caused by machining inaccuracies of the axis of rotation location. If the control system can be intelligent enough to compensate for such machining errors, then one may be able to improve the accuracy of the velocity control, or alternatively, one may maintain the same accuracy and relax the machining tolerances required. This could decrease cost significantly. Experiments are performed testing repetitive control methods on a constant speed rolling operation testbed. The experimental results show very substantial decreases in the tracking error of the system. Spectral data of the output motion are given to demonstrate the attenuation of the disturbance frequencies and harmonics, related to the bandwidth being used. It is seen that the simplest form of repetitive control which is very easily implemented, can produce striking improvement in control system performance in such belt drive rolling operations, and the learning can be accomplished in a short time.

• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.359-360
• /
• 2006

Magnetic Flux Leakage (MFL) methods are widely employed for the non-destructive testing of gas pipelines. In the application of MFL pipeline inspection technology, corrosion anomalies are detected and identified via their leakage filed due to changes in wall thickness. This paper presents discrete cosine transform (DCT) based MFL signal analysis for defect feature extraction of natural gas pipelines. The original MFL signals are transformed into new ones based on the analysis. The usefulness of the approach has been shown by the experimental results.

• Proceedings of the KSR Conference
• /
• 2003.10c
• /
• pp.151-156
• /
• 2003

The Communication Based Train Control(CBTC) System generally used to improving existing lines in the world is efficient and stable for improvement. Also it is efficient for improvement because it does not cause any problems in operation of existing lines. We examined the mixed operation scheme for more efficient and stable improvement when improvement is implemented depending on aged equipment and the increased number of passengers in the Korean city railroad. The biggest point in the mixed operation is to implement a stable test without interfering with the operation of the existing lines. For this purpose, we deduced a method of installing the equipment, a method of testing depending on the installed equipment, and the types of mixed operation, and presented a scheme of execution of the methods depending on the mixed operation.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.1 no.1
• /
• pp.128-134
• /
• 2012

This paper gives an overview of the requirements for electrical equipment in potentially explosive atmospheres and describes how these are applied to electrical machines and drives in hazardous areas. The method by which equipment can be shown to be safe in a whole range of gases, by testing in a single test gas, is covered. It is shown how the more recently introduced methods of protection for hazardous areas, increased safety and nonsparking, are ideally suited to AC machines and drives. A novel method of measuring the fullload temperature rise of electrical machines for hazardous, and other areas, without the need to connect a mechanical load to the machine's drive shaft is explained.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2006.03a
• /
• pp.25-32
• /
• 2006

We present a imaging method of seismic sources by time reversal propagation of seismic waves. Time-reversal wave propagation is actively used in medical imaging, non destructive testing and waveform tomography. Time-reversal wave propagation is based on the time-reversal invariance and the spatial reciprocity of the wave equation. A signal is recorded by an array of receivers, time-reversed and then back-propagated into the medium. The time-reversed signal propagates back into the same medium and the energy refocuses back at the source location. The increasing power of computers and numerical methods makes it possible to simulate more accurately the propagation of seismic waves in heterogenous media. In this work, a staggered-grid finite-difference solution of the elastic wave equation is employed for the wave propagation simulation. With numerical experiments, we show that the time-reversal imaging will enable us to explore the spatio-temporal history of complex earthquake.

• Proceedings of the Korean Reliability Society Conference
• /
• 2005.06a
• /
• pp.303-305
• /
• 2005

Recently, various plastics are used for improvement of reliability and thermal stability of electronic goods. But, it is difficult to choose suitable balance of grade resin to each other product property. Selection of high efficiency resin is becoming inescapable circumstance according to change of reflow temperature of product and development of product following to lead free. Using a inexpensive and reasonable resin, that sustain a uniform performance of product quality. It is make a robust product and increase a company's competitive power. Hereupon, I introduce example that use ESPI methods of thermal deformation analysis of product using in our company product. I try to refer to a structural weak point detection of real time measurement of electronic parts instead of mechanical and chemical measurement of specimen type.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.11a
• /
• pp.226-227
• /
• 2019

Installation and usage methods are currently different between China and Korea for the same rubber asphalt waterproofing sealant. Quality verification is not properly carried out in this situation, so it is necessary to secure reliability in order to export domestic materials to China. In this study, rubber asphalt waterproofing sealant used as injection-type leakage repair material was tested in accordance to adhesion strength quality test method outlined in the JC/T2428 Chinese Industrial Standard to confirm the basic performance is compliant or not.

• Journal of muscle and joint health
• /
• v.28 no.2
• /
• pp.91-101
• /
• 2021

Purpose: This study was conducted to identify factors related to osteoporosis prevalence in postmenopausal women. Methods: This study was a secondary analysis research using data from the Eighth Korea National Health and Nutrition Examination Survey (KNHANES VIII-1), 2019, which were downloaded from the KNHANES website. The subjects of this study were 1,791 postmenopausal women who participated in the KNHANES VIII-1, 2019. Data analysis was performed using the IBM SPSS 21.0 program and complex sample design analysis was performed considering factors such as weight, cluster, and strata. Results: Osteoporosis prevalence of in postmenopausal women was 17.5%. Factors related to osteoporosis prevalence were age (65~74 years old, ≥75 years old), house income (low), household type (one-person household), postmenopausal period (10~19 years), drinking (non-drinking). Conclusion: Interventions for osteoporosis prevention and management in postmenopausal women need to focus on women less than 10 years after menopause and one-person household women. Furthermore, it is necessary to expand bone density testing for the early detection of osteoporosis in postmenopausal women.