• Journal of Welding and Joining
• /
• 제15권5호
• /
• pp.74-83
• /
• 1997

Effect of welding parameters such as current, speed and electrode pressure on the weld quality of tin coated steels for small containers was discussed in this paper. Welding was performed with low frequency wire seam welding system which was loaded with 1.5mm in diameter copper wire electrode. The welding parameters were monitored at the position close to the welding spot so as to minimize the instrumentation error, and the signals were stored into a digital data acquisition system before analysis. Results showed that critical current for sufficient nugget size increased as the base material thickness increased, while the width of the optimum welding range was reduced. The acceptable welding condition derived from this study was found to be effective within the thickness range of $\pm$10% of the nominal (0.25mm) thickness. Tin coating layer was proved not to affect seriously on the weld quality, i.e. strength and formability, since consumable wire electrode was used in this process. Test results also demonstrated that the welding current was thought to be the most effective parameter to form an acceptable weld, while welding speed or electrode pressure exerted less effect on the nugget formation. However, these two parameters played an important role because the former was related to the nugget overlap interval, and the latter, to the formation of expulsion during welding.

• Journal of Welding and Joining
• /
• 제32권1호
• /
• pp.61-65
• /
• 2014

The purpose of this study is to evaluate the applicability of the element stress to establish S-N design curve for the welded lap joint with thin plates below 2mm thickness. In order to do it, the extensive fatigue tests of the welded lap joints with INVAR alloy were performed. With the results, the deign S-N curves for the lap-weld were established by using the reference stresses such as the nominal stress range at the weld throat area, hot spot stress range and element stress range, and compared with regard to the standard deviation. The standard deviation of S-N curves with element stress range was less than that of S-N curves with other reference stresses. In addition, FEA results show the amount of the element stress is less sensitive to mesh size. Based on the results, it can be concluded that the element stress is to be used as the reference stress for the design S-N curves of the welded lap joint.

• 한국해양공학회지
• /
• 제25권5호
• /
• pp.47-51
• /
• 2011

This paper analyzes the fatigue-life of welded joints using the notch stress approach. In the notch stress approach, the notch effects are usually approximated by introducing weld-bead parameters for the local detailed weld joints. The actual bead shape is complex and 3-dimensional. It may also greatly influence the fatigue strength. In this study, the welded shape was modeled using a 3D-scanner. The critical distance method was adopted in the evaluation of the fatigue effective notch stress for the weldments. Fatigue life tests were performed to verify the present method of fatigue life estimation for two types of welded plates with longitudinal attachments. The estimated results of the present methods were applied to the results of the experiment. The results of the analysis showed that the scatter of fatigue-life for the experimental data expressed in the nominal stress was significantly reduced by applying the effective fatigue stress of the present study.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제34회 춘계학술대회논문집
• /
• pp.71-74
• /
• 2010

한국형발사체 엔진에 사용될 것으로 예상되는 75톤급 연소기의 기술검증시제를 이용하여 2회 연소시험을 수행하였다. 설비 공급 능력과 구조물 강도 제한으로 정상 유량의 50% 수준에서 시험이 수행되었다. 채널냉각 연소기를 이용한 저압연소시험을 통해 점화구간과 연소구간에서의 신뢰도와 안정성이 확인되었다. 더불어 75톤 연소기가 성능요구조건을 만족시킬 수 있을 것으로 추정할 수 있었다.

• Steel and Composite Structures
• /
• 제4권2호
• /
• pp.149-167
• /
• 2004

Offshore platforms have to serve in harsh environments and hence are likely to be damaged due to wave induced fatigue and environmental corrosion. Welded tubular joints in offshore platforms are most vulnerable to fatigue damage. Such damages endanger the integrity of the structure. Therefore it is all the more essential to assess the capacity of damaged structure from the point of view of its safety. Eight internally ring stiffened fatigue damaged tubular joints with nominal chord and brace diameter of 324 mm and 219 mm respectively and thickness 12 mm and 8 mm respectively were tested under axial brace compression loading to evaluate the reserve capacity of the joints. These joints had earlier been tested under fatigue loading under corrosive environments of synthetic sea water and hence they have been cracked. The extent of the damage varied from 35 to 50 per cent. One stiffened joint was also tested under axial brace tension loading. The residual strength of fatigue damaged stiffened joint tested under tension loading was observed to be less than one fourth of that tested under compression loading. It was observed in this experimental investigation that in the damaged condition, the joints possessed an in-built load-transfer mechanism. A bi-linear stress-strain model was developed in this investigation to predict the reserve capacity of the joint. This model considered the strain hardening effect. Close agreement was observed between the experimental and predicted results. The paper presents in detail the experimental investigation and the development of the analytical model to predict the reserve capacity of internally ring stiffened joints.

• 한국강구조학회 논문집
• /
• 제26권1호
• /
• pp.31-42
• /
• 2014

본 연구에서는 콘크리트충전 각형강관에 구조용 피복콘크리트를 적용한 합성기둥에 대하여 연구하였다. 1/3~1/2 축소모델의 편심 압축실험체 4개와 중심압축실험체 1개를 제작하여 압축실험을 수행하였다. 실험 변수는 피복콘크리트의 강섬유 첨가여부, 편심거리, 기둥 길이, 그리고 횡보강 상세이다. 일부 실험체에서 최대강도 도달 후 피복콘크리트의 탈락으로 인한 강도저하가 발생하였으나 모든 실험체는 현행 설계기준(KBC 2009)에 의한 휨 압축 강도 및 공칭 압축강도를 초과하는 하중재하능력을 보였다.

• 한국공간구조학회논문집
• /
• 제19권1호
• /
• pp.45-51
• /
• 2019

In this study, the static load test and the load transfer test were carried out to evaluate the structural performance of the circular anchorage proposed by the previous study. Specimens were fabricated according to KCI-PS101 and ETAG 013. As a result of the static load test, it was verified that the displacement of the wedge and the strand was kept constant when the tensile force of 80% of the nominal strength of the strand was applied. In the load transfer test, it was confirmed that all the specimens satisfied the stabilization formula of KCI-PS101 and ETAG 013. Post-tensioned one-way slab with circular anchorage were fabricated to evaluate the flexural behavior. All specimens exhibited the same flexural behavior and maximum load. However, the specimen with circular anchorage were advantageous than the rectangular anchorage one in terms of crack control of the anchorage zone.

• Advances in concrete construction
• /
• 제10권6호
• /
• pp.515-526
• /
• 2020

Cold-mixed asphalt mixture is a widely recommended asphalt pavement materials with potentially economic and environmental benefits. Due to the reduction of natural non-renewable mineral resources, powder minerals with similar properties are considered as new mineral fillers in asphalt mixtures. This study explored the feasibility of using cement to replace natural limestone powder (LP) in emulsified asphalt concrete modified by styrene-butadiene styrene copolymer. The experimental tests, including compressive strength, Marshall stability as well as moisture susceptibility test, were used to investigate the mechanical properties, the Marshall stability, flow value, as well as the moisture damage. In addition, the influence of material composition on the performance of asphalt concrete is explained by the microstructure evolution of the pore structure, the interface transition zone (ITZ), and the micromorphology. Due to mineralogical reactivity of cement, its replacement part of LP improved the mechanical properties, Marshall stability, but it will reduce the moisture susceptibility and flow value. This is because with the increase of the cement substitution rate, the pore structure of the asphalt concrete is refined, the width of ITZ becomes smaller, and the microstructure is more compact. In addition, asphalt concrete with a larger nominal particle size (AC-16) has relatively better performance.

• 한국강구조학회 논문집
• /
• 제26권2호
• /
• pp.91-103
• /
• 2014

최근에 인장강도 800MPa급 고성능 강재가 개발되었지만 플랜지와 복부판의 상호작용을 고려한 플레이트 거더의 국부좌굴에 대한 연구는 아직까지 미흡한 실정이다. 본 연구는 HSB 800을 적용한 플레이트 거더의 플랜지 국부좌굴에 대한 강도를 비선형 유한요소해석으로 평가하였다. 비선형 해석 시 I-단면을 갖는 플레이트 거더의 플랜지와 복부판은 3차원 쉘요소로써 초기결함 및 잔류응력을 고려하였으며, 고성능 강재의 재료모델은 다중선형 재료로 모형화하였다. 이를 적용하여 복부판이 조밀, 비조밀 그리고 세장 단면을 갖는 압축 플랜지에 대해 매개변수 해석을 수행하였다. 플레이트 거더의 플랜지 국부좌굴에 대한 거동을 분석하였고, 본 연구의 비선형 해석 결과를 AASHTO LRFD(2012)와 도로교설계기준(한계상태설계법, 2012)의 압축플랜지 공칭휨강도와 비교하여 평가하였다.

• 콘크리트학회논문집
• /
• 제24권3호
• /
• pp.225-232
• /
• 2012

이 연구는 순환잔골재를 사용한 콘크리트의 전단거동을 평가하고자 하였다. 추가적으로 순환굵은골재를 현행규준식 및 제안식과 비교/분석하였다. 동일한 압축강도를 갖는 5개의 실험체를 계획하였으며 각 실험체는 순환잔골재치환율(0%, 30%, 60%, 70%, 100%)을 변수로 계획하였으며 전단철근은 보강하지 않았다. 실험에 사용한 순환잔골재는 흡수율과 비중을 만족하는 골재를 사용하였다. 사용한 골재 중 70% 치환한 실험체의 경우 저품질의 순환잔골재를 사용하였다. 실험은 하중-변위관계, 전단변형, 경사균열하중, 균열패턴, 최대전단강도, 파괴모드를 분석하여 평가하였다. 실험 결과 순환잔골재를 사용한 철근콘크리트 보의 전단거동은 천연골재와 비교하여 전반적으로 큰 차이를 보이지 않았으나, 전단에 관한 규준식 및 제안식과 비교한 결과 순환잔골재를 사용한 철근콘크리트 보의 경우 규준식 수정을 통한 새로운 제안식이 필요할 것으로 판단된다.