• Journal of Power System Engineering
• /
• v.18 no.1
• /
• pp.22-31
• /
• 2014

This paper introduced the new calibration algorithm of a straight-type five-hole pressure probe necessary for calculating three-dimensional flow velocity components. The new velocity data reduction method using both a commercial two-dimensional curve-fitting program and the zone partition method of a calibration map was firstly introduced in this study. This new calibration method can be applied up to the wide flow angle of ${\pm}80^{\circ}$ despite of using a five-hole pressure probe because this data reduction method showed a comparatively good performance in calculating yaw and pitch angles from the calibration map.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.25 no.6
• /
• pp.475-482
• /
• 2005

The iterative calculation by least square method was used to determine the source location of acoustic emission in rock, as so called "traditional method". The results were compared with source coordinates infered from the application of neural network system for new input data, as so called "new method". Input data of the neural network were based on the time differences of longitudinal waves arrived from acoustic emission events at each transducer, the variation of longitudinal velocities at each stress level, and the coordinates of transducer as in the traditional method. The momentum back propagation neural network system adopted to determine source location, which consists of three layers, and has twenty-seven input processing elements. Applicability of the new method were identified, since the results of source location by the application of two methods were similarly concordant.

• Journal of the Korean Society of Safety
• /
• v.12 no.4
• /
• pp.180-190
• /
• 1997

A new method in the fault tree analysis (FTA) for the reliability calculation is suggested. Two steps are necessary in traditional method in evaluation of the occurrence probability of top event in fault tree (FT). The first step is to find the minimal outsets, and the second one is to substitute the result into the poincare equation. In order to reduce the enormous computing time of this method, lots of rapid algorithms have been developed. Almost of all achievements were, however, based on the partial structural properties of FT. In this paper, the FT is transformed to a non-linear graph G which has the same minimal outsets of original n, and then the reliability is calculated using the domination theory. In this new method, the required number of equation terms are at most $2^n$ (n is node number of graph G), while $2^m$-1 (m is the number of minimal cutsets) calculation terms are required in the poincare equation in traditional method. Since m>>n in general. our new method reduces the calculation time significantly.

• Fibers and Polymers
• /
• v.6 no.4
• /
• pp.339-342
• /
• 2005

In this paper, a hand-operating method (tiled test method) of the wool-blending sample is made out, and make use of the method, the test of wool-blending bundle in different blending ratio is accomplished. According to the test data, the synthesis method of the stretch curve is worked out and the synthesis software for the typical stretch curve of wool-blending bundle is designed. Through laboratory hand-operating method, the blending fasciculus applying to fiber bundle test can be obtained in a short time. Calculation for sampling is accomplished in the article. We bring up 9 new signs to describe the characteristics of the curve behind peak for the first time: elongation behind peak (HE), elongation percentage behind peak (HEP), relative elongation rate behind peak (RHE), total break work $(W_a)$, break work behind peak (HW), break work coefficient behind peak (HWC), elongation percentage of half-load behind peak (HEL), load percentage of half-elongation behind peak (HLE), break efficiency behind peak (HEC).

• Journal of the Korean Operations Research and Management Science Society
• /
• v.37 no.4
• /
• pp.67-72
• /
• 2012

In this paper a new method of handling linear constraints for the genetic algorithm is suggested. The method is designed to maintain the feasibility of offsprings during the evolution process of the genetic algorithm. In the genetic algorithm, the chromosomes are coded as the vectors in the real vector space constrained by the linear constraints. A method of handling the linear constraints already exists in which all the constraints of equalities are eliminated so that only the constraints of inequalities are considered in the process of the genetic algorithm. In this paper a new method is presented in which all the constraints of inequalities are eliminated so that only the constraints of equalities are considered. Several genetic operators such as arithmetic crossover, simplex crossover, simple crossover and random vector mutation are designed so that the resulting offspring vectors maintain the feasibility subject to the linear constraints in the framework of the new handling method.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.40 no.5
• /
• pp.11-19
• /
• 2008

The paper established a new method for fast measurement and characterizing of sub-visible dirt of recycled paper which is too small to be seen with naked eye. This method provided a new way for the evaluation of recycled paper that is hard to be characterized by the conventional method. Two effective thresholding algorithms HA and SDA were compared and their applicable conditions were discussed. Results showed that the HA could be used for un-printed paper while SDA is suited for recycled papers. The gloss of paper samples was measured and the relation between gloss and sub-visible dirt was investigated. The significant effect of this method for characterizing and comparing paper was exhibited. The experiment results indicated that sub-visible dirt measuring method could be a complementariness of the conventional methods.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2010.04a
• /
• pp.23-25
• /
• 2010

In this paper, we studied linking method for updating navigation map with new address map. This method is hierarchical as we chose candidate using attribute data for geometry matching. Limiting a matching range, we conducted a experiment ICP with geometry matching. As a result, for linking method it's quite satisfied but for updating method, we decided that we have to do more precise method for updating.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.35 no.4
• /
• pp.148-155
• /
• 1986

This paper presents a new decoupled power system state estimation method. The decoupling is achieved via simple linear transformation on power measurements in contrast with the modified fast decoupled state estimation method which assumes decoupling by direct negligence of the off-diagonal blocks of the observation functions. The new estimation method is compared with the modified decoupled state estimation method against IEEE-14 bus model power system and 25 bus model power system in several system conditions. It is observed that the proposed method shows better convergence performance and filtering performance than a modified fast decoupled state estimation.

• Journal of the Korea Safety Management & Science
• /
• v.18 no.3
• /
• pp.147-154
• /
• 2016

This paper suggests a specific model that could efficiently improve the interaction and the interface between MES(Manufacturing Execution System) server and PDA terminal through RFID(Radio Frequency Identification) system and bar-code system in automative transmission shipment place of the finished assembly parts. The proposed model shows that the new method by RF-Tag system can more efficiently perform to reduce processing time and loading time for shipment, compared with the current approach by bar-code system. It is noted in case of the method by RF-Tag that the effects of proposed model are as follows; (a) While the shipping lead time per truck for carrying by the current method was 35 minutes, the shipping lead time by the new method was 15 minutes. (b) While the accuracy for carrying by the current method was 50%, the accuracy by the new method was 99%.

• Journal of the Korea Safety Management & Science
• /
• v.19 no.3
• /
• pp.49-58
• /
• 2017

This paper suggests a specific model that could efficiently improve the interaction and the interface between MES(Manufacturing Execution System) server and POP(Point of Production) terminal through electronic document server and electronic pen, bluetooth receiver and form paper in disassembly and process inspection works. The proposed model shows that the new method by electronic document automation system can more efficiently perform to reduce processing time for maintenance work, compared with the current approach by handwritten processing system. It is noted in case of the method by electronic document automation system that the effects of proposed model are as follows; (a) While the processing time per equipment for maintenance by the current method was 300 minutes, the processing time by the new method was 50 minutes. (b) While the processing error ratio by the current method was 20%, the error ratio by the new method was 1%.