• Asian-Australasian Journal of Animal Sciences
• /
• v.12 no.4
• /
• pp.537-543
• /
• 1999

Whole horse beans (Vicia faba cv. Alfred) (WHB) were pressure toasted at different temperatures of 100, 118 and $136^{\circ}C$ for 3, 7, 15 and 30 minutes in order to determine an optimal heating conditions to increase bypass starch (BPSt) as glucose source which is usually limiting nutrient in highly producing dairy cows in the Netherlands. Starch (St) Ruminal Degradative Kinetics and Fermentation Characteristics of (SRDC) of WHB were determined using in sacco technique in 4 lactating dairy cows fed 47% hay and 53% concentrate according to Dutch dairy cow requirements. Measured characteristics of St were soluble fraction (S), potentially degradable fraction (D) and rate of degradation (Kd) of insoluble but degradable fraction. Based on measured characteristics, percentage bypass starch (BPSt) was calculated according to the Dutch new feed evaluation system: the DVE/OEB system. Pressure toasting temperatures significantly affected starch gelatinization (p<0.01). Degradability of Starch in the rumen was highly reduced by pressure toasting (p<0.01). S varied from 58.2% in the raw WHB (RWHB as a control) to 19.6% in $136^{\circ}C/15min$. S was reduced rapidly with increasing time and temperature (p<0.01). D varied from 41.8% in RWHB to 80.5% in $136^{\circ}C/15min$. D fraction was enormously increased with increasing time and temperature (p<0.01). Kd varied from 4.9%h in RWHB to 3.4%/h in $136^{\circ}C/15min$. All these effects resulted in increasing %BPSt from 29.0% in RWHB to 53.1% in $136^{\circ}C/15min$. Therefore BPSt increased from 93.5 g/kg in RWHB to 173.5 g/kg in $136^{\circ}C/15min$. The effects of pressure toasting on %BPSt and BPSt seemed to be linear up to the highest values tested. Therefore no optimal pressure toasting conditions could be determined at this stage. But among 10 treatments, The treatment of $136^{\circ}C/15min$was the best with the highest BPSt content. It was concluded that pressure toasting was effective in shifting starch degradation from rumen to small intestine to increase bypass starch.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.195-195
• /
• 2016

Titanium and its alloys are widely used as implants in orthopedics, dentistry and cardiology due to their outstanding properties, such as high strength, high level of hemocompatibility and enhanced biocompatibility. Hence, recent works showed that the synthesis of new Ti-based alloys for implant application involves more biocompatible metallic alloying element, such as, Nb, Hf, Zr and Mo. In particular, Nb and Hf are one of the most effective Ti ${\beta}-stabilizer$ and reducing the elastic modulus. Plasma electrolyte oxidation (PEO) is known as excellent method in the biocompatibility of biomaterial due to quickly coating time and controlled coating condition. The anodized oxide layer and diameter modulation of Ti alloys can be obtained function of improvement of cell adhesion. Silicon (Si) and magnesium (Mg) has a beneficial effect on bone. Si in particular has been found to be essential for normal bone and cartilage growth and development. In vitro studies have shown that Mg plays very important roles in essential for normal growth and metabolism of skeletal tissue in vertebrates and can be detected as minor constituents in teeth and bone. The aim of this study is to research Si and Mg doped hydroxyapatite film formation by plasma electrolytic oxidation. Ti-29Nb-xHf (x= 0, 3, 7 and 15wt%, mass fraction) alloys were prepared Ti-29Nb-xHf alloys of containing Hf up from 0 wt% to 15 wt% were melted by using a vacuum furnace. Ti-29Nb-xHf alloys were homogenized for 2 hr at $1050^{\circ}C$. Each alloy was anodized in solution containing typically 0.15 M calcium acetate monohydrate + 0.02 M calcium glycerophosphate at room temperature. A direct current power source was used for the process of anodization. Anodized alloys was prepared using 270V~300V anodization voltage at room. A Si and Mg coating was produced by RF-magnetron sputtering system. RF power of 100W was applied to the target for 1h at room temperature. The microstructure, phase and composition of Si and Mg coated oxide surface of Ti-29Nb-xHf alloys were examined by FE-SEM, EDS, and XRD.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.197-197
• /
• 2016

Commercially pure titanium (CP Ti) and Ti-6Al-4V alloys have been widely used for biomedical applications. However, the use of the Ti-6Al-4V alloy in biomaterial is then a subject of controversy because aluminum ions and vanadium oxide have potential detrimental influence on the human body due to vanadium and aluminum. Hence, recent works showed that the synthesis of new Ti-based alloys for implant application involves more biocompatible metallic alloying element, such as, Nb, Hf, Zr and Mo. In particular, Nb and Hf are one of the most effective Ti ${\beta}-stabilizer$ and reducing the elastic modulus. Plasma electrolyte oxidation (PEO) is known as excellent method in the biocompatibility of biomaterial due to quickly coating time and controlled coating condition. The anodized oxide layer and diameter modulation of Ti alloys can be obtained function of improvement of cell adhesion. Manganese(Mn) plays very important roles in essential for normal growth and metabolism of skeletal tissue in vertebrates and can be detected as minor constituents in teeth and bone. Radio frequency(RF) magnetron sputtering in the various PVD methods has high deposition rates, high-purity films, extremely high adhesion of films, and excellent uniform layers for depositing a wide range of materials, including metals, alloys and ceramics like a hydroxyapatite. The aim of this study is to research the Mn coatings on the micro-pore formed Ti-29Nb-xHf alloys by RF-magnetron sputtering for dental applications. Ti-29Nb-xHf (x= 0, 3, 7 and 15wt%, mass fraction) alloys were prepared Ti-29Nb-xHf alloys of containing Hf up from 0 wt% to 15 wt% were melted by using a vacuum furnace. Ti-29Nb-xHf alloys were homogenized for 2 hr at $1050^{\circ}C$. Each alloy was anodized in solution containing typically 0.15 M calcium acetate monohydrate + 0.02 M calcium glycerophosphate at room temperature. A direct current power source was used for the process of anodization. Anodized alloys was prepared using 270V~300V anodization voltage at room. Mn coatings was produced by RF-magnetron sputtering system. RF power of 100W was applied to the target for 1h at room temperature. The microstructure, phase and composition of Mn coated oxide surface of Ti-29Nb-xHf alloys were examined by FE-SEM, EDS, and XRD.

• International Journal of Highway Engineering
• /
• v.13 no.2
• /
• pp.41-48
• /
• 2011

Warm-mix asphalt(WMA) technology has been developed to allow asphalt mixtures to be produced and compacted at a significantly lower temperature. The WMA technology was identified as one of means to lower emissions for $CO_2$ and has been spread so quickly in the world. Recently, two innovative WMA additives has been developed to reduce mixing and paving temperatures applied in asphalt paving process in Korea. Since the first public demonstration project in 2008, many WMA projects have successfully been constructed in national highways. In 2010, the WMA field trial was conducted on new national highway construction under Dae-Jeon Regional Construction Management Administration. The two different WMA loose mixtures(WMA and WMA-P) and a HMA mixture were collected at the asphalt plant to evaluate their mechanical performance in the laboratory. The Third-scale Model Mobile Loading Simulator(MMLS3) was adopted to evaluate rutting resistance and moisture damage under different traffic and environmental conditions. In this study, plant-produced WMA mixtures using two WMA additives along with the conventional hot mix asphalt(HMA) mixtures were evaluated with respect to their rutting resistance and moisture susceptibility using MMLS3. Based on the limited laboratory test results, plant-produced WMA mixtures are superior to HMA mixtures in rutting resistance and the moisture susceptibility. The WMA additive was effective for producing and compacting the mixture at $30^{\circ}C$ lower than the temperature for the HMA mixture.

• Korean Journal of Food Science and Technology
• /
• v.30 no.2
• /
• pp.397-406
• /
• 1998

Hen egg white lysozyme (HEWL) is very valuable as a natural preservative in food processing due to its selective bactericidal activity. HEWL which traditionally isolated by crystallization or freeze drying was simply separated from 13 different hen egg white (HEW) proteins by a single-step ultrafiltration. Freeze dried HEW (0.25%, w/v) dissolved in a citrate-phosphate buffer (pH 4.6) was ultrafiltered with a PM30 membrane under various operating conditions, by changing concentration, temperature, transmembrane pressure $({\triangle}P_T)$, and stirring speed. Optimum separation conditions were decided when maximal flux was obtained. Under the optimum separation conditions, the effect of membrane material and fouling on flux as time passed as well as lysozyme concentration, protein concentration, specific activity (SA) in the permeate were measured. Best separation conditions of HEWL with PM30 membrane were sample concentration 0.25%, temperature $35^{\circ}C$, ${\Delta}P_T\;30\;psi$, and stirring speed 300 rpm. During the first 12 min, the flux of YM30 was higher, but at the steady-state it was lower than that of PM30. The SA of the PM30 permeate was over 2 times higher in spite of the lysozyme and protein concentration being lower than that of YM30 permeate. The flux of 5 times used PM30 decreased 30% compared to a new PM30, but both had the same tendency in flux decrease when time passed. Both of them reached a steady-state after 35 min and remained at 70% of the initial flux. In the PM30 permeate, the lysozyme concentration and SA were 110 units/mL and 2,821 units/mg protein, respectively. Therefore, PM30 membrane separation was very effective for separation of antimicrobial lysozyme.

• Current Research on Agriculture and Life Sciences
• /
• v.32 no.1
• /
• pp.1-9
• /
• 2014

In contrast to conventional microwaves, QRD (Quadratic Residue Diffusor) microwaves are a new energy-efficient technology that enhances the effect of sterilization based on changing the wavelength phase difference. Therefore, this study investigated the sterilization of wood using environmentally friendly and low energy consuming QRD microwaves. The results are as follows: for the QRD microwaves used in this study, the efficiency E = 5.75e0.32 S ($R^2$=0.908). Although the early water content was not constant, the average water content was 30.3% and after one week of natural drying, the water content was 22.6%, representing an average water content reduction of about 8%. When increasing the microwave level from 3 kW ~ 9 kW, the time taken for the temperature to increase was reduced. After the QRD microwave treatment, the wood samples showed no change in their flexural rigidity, compressive strength, or cleavage. The QRD microwave levels used in the experiments were 3, 5, 7, and 9 kW, where 9 kW was found to be the most efficient. Thus, for the purpose of eliminating nematodes and termites inside wood, a higher QRD microwave level was found to be more effective and energy efficient.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.9 no.2
• /
• pp.20-29
• /
• 2006

Modeling urban climate caused by land use conversion is critical for human welfare and sustainable development, but has hampered because detailed information on urban characteristics is hard to obtain. With the advantage of satellite observations and the new statistical boundary system, this paper measures the economic and environmental effects of green area loss due to land use conversion in urban areas. To perform this purpose, data were collected from the various sources basic statistical unit data from the National Statistical Office, digital maps from the National Geographic Information Institute, satellite images, and field surveys when necessary. All data (maps and attributes) are built into the geographic information system (GIS). This paper also utilizes Landsat TM 5 imagery of Daegu city to derive vegetation index and to measure average surface temperature. The satellite data were examined using standard image processing software, ERDAS IMAGINE, and the results of the digital processing were presented with ARCVIEW(v.3.3). SAS package was used to perform statistical analyses. This study presents that there exists a strong relationship between land use change and climatic change as well as land price change. Based on results of the analysis, this paper suggests that planners should implement effective tools and policies of urban growth management to detect environmental quality and to make right decisions on policies concerning smart urban growth.

• Journal of Energy Engineering
• /
• v.23 no.4
• /
• pp.95-105
• /
• 2014

The CUPID code has been developed for a transient, three-dimensional, two-phase flow analysis at a component scale. It has been validated against a wide range of two-phase flow experiments. Especially, to assess its applicability to single- and two-phase flow analyses in the Calandria vessel of a CANDU nuclear reactor, it was validated using the experimental data of the 1/4-scaled facility of a Calandria vessel at the STERN laboratory. In this study, a preliminary thermal-hydraulic analysis of the CANDU reactor moderator tank using the CUPID code is carried out, which is based on the results of the previous studies. The complicated internal structure of the Calandria vessel and the inlet nozzle was modeled in a simplified manner by using a porous media approach. One of the most important factors in the analysis was found to be the modeling of the tank inlet nozzle. A calculation with a simple inlet nozzle modeling resulted in thermal stratification by buoyance, leading to a boiling from the top of the Calandria tank. This is not realistic at all and may occur due to the lack of inlet flow momentum. To improve this, a new nozzle modeling was used, which can preserve both mass flow and momentum flow at the inlet nozzle. This resulted in a realistic temperature distribution in the tank. In conclusion, it was shown that the CUPID code is applicable to thermal-hydraulic analysis of the CANDU reactor moderator tank using the cost-effective porous media approach and that the inlet nozzle modeling is very important for the flow analysis in the tank.

• Nuclear Engineering and Technology
• /
• v.27 no.3
• /
• pp.301-316
• /
• 1995

experimental and computational studies ore carried out to investigate the natural convection of the single phase flow in a tank with a heated horizontal plate facing downward. This is a simplified model for investigations of the influence of a core melt at the bottom of a reactor vessel on the thermal hydraulic behavior in a oater filled cavity surrounding the vessel. In this case the vessel is simulated by a hexahedron insulated box with a heated plate Horizontally mounted at the bottom of the box. The box with the heated plate is installed in a water filled hexahedron tank. Coolers are immersed in the U-type water volume between the box and the tank. Although the multicomponent flows exist more probably below the heated plate in reality, present study concentrates on the single phase flow in a first step prior to investigating the complicated multicomponent thermal hydraulic phenomena. In the present study, in order to get a better understanding for the natural convection characteristics below the heated plate, the velocity and temperature are measured by LDA(Laser Doppler Anemometry) and thermocouples, respectively. And How fields are visualized by taking pictures of the How region with suspended particles. The results show the occurrence of a very effective circulation of the fluid in the whole How area as the heater and coolers are put into operation. In the remote region below the heated plate the new is nearly stagnant, and a remarkable temperature stratification can be observed with very thin thermal boundary. Analytical predictions using the FLUTAN code show a reasonable matching of the measured velocity fields.

• Journal of Veterinary Clinics
• /
• v.28 no.3
• /
• pp.273-279
• /
• 2011

Botulinum toxin type A (BoNT/A) has been proven to be a safe and effective treatment for wrinkles in human. As well as the anti-wrinkle effects, the anti-pruritic effect of BoNT/A has been revealed from several researches for new therapy. The aim of this study was to investigate the anti-pruritic effect of BoNT/A against histamine-induced pruritus on canine skin. Five clinically healthy beagles were included in the study. All dogs were received 0.05 ml (5 Unit) of BoNT/A on the right dorsal thoracic region as an experiment and the same volume of saline solution was injected on the left dorsal thoracic region as a control, respectively. Intradermal histamine injections were performed four times (before treatment and days 1, 3 and 7 after BoNT/A injection). The severity of pruritus, the diameter and thickness of wheal, the erythema index and cutaneous temperature were assessed. The severity of pruritus was reduced on BoNT/A treated sides, compared with saline treated sides (p < 0.05). BoNT/A decreased wheal size, in both diameter and thickness (p < 0.05). Although, erythema index of both sides were increased after first histamine injection, BoNT/A treated sides showed the low-value as compared with saline treated sides. Cutaneous temperature was decreased significantly on BoNT/A treated sides. These results indicates that BoNT/A reduce histamine-induced pruritus on canine skin and suggested a possibility of application of BoNT/A for local intractable dermatologic problem in dogs.