• Journal of Electrical Engineering and Technology
• /
• v.13 no.2
• /
• pp.752-760
• /
• 2018

In this paper, interior permanent magnet synchronous motor (IPMSM) design for sensorless drive, considering magnetic neutral point shift according to magnetic saturation, has been proposed. Sensorless control was divided into a method based on inductance and a method based on back induced voltage. Because induced voltage is very small at zero or low speed, error in rotor initial position estimation may occur. Using the ratio of saliency addresses this problem. When using high-frequency injections at low speed, the rotor's initial position is estimated at the smallest portion of the inductance. IPMSM has the minimum inductance at the d-axis. However, if magnetic saturation leads to magnetic neutral point variation, following the load current change, there is a change in the minimum point of inductance. In this case, it can lead to failure of initial rotor position estimation. As a result, it is essential that the blocking design has an inductance minimum point shift. As such, in this study, an IPMSM design method, by blocking magnetic neutral point change, has been proposed. After determining the inductance profile based on the finite element analysis (FEA), the results of proposed method were verified.

• Journal of The Korean Society of Integrative Medicine
• /
• v.5 no.1
• /
• pp.67-74
• /
• 2017

Purpose : Forward head posture is typical neck disorders occur in all people. And this attitude causes a shortening and weakening of the muscles in the body. It also causes excessive extension acts as a reward. This attitude has to change if the pain occurs around the neck and shoulders, and are subjected to unusual stress. Patients with chronic neck pain associated with forward head posture was found to be the more severe the fall of the respiratory, forward head posture poor quality of much breath. The purpose of this study was to compare the effect of changes in forward head posture and neutral head posture on respiratory. Method : Forty volunteers were participated in study and divided into two groups [forward head posture group (n=20) and neutral head posture group (n=20)]. We measured cervical alignment with global postural system to find out a forward head posture. Respiratory function was measured with a SPIROVIT SP-1 equipment and we found out a forced vital capacity (FVC), forced expiratory volume at one second (FEV1) and FEV1/FVC. A pared t-test was used to determine a statistical significance for the pulmonary function variation and a independent t-test was used to determine a statistical significance in the two groups. Results : In the experimental group, FVC and FEV1 were significantly higher in the artificial neutral head posture than in the forward head posture. In the control group, FVC and FEV1 were significantly higher in the neutral head posture than in the forward head posture. FVC, FEV1, and FEV1/ FVC were significantly higher in the neutral head posture of control group than the artificial neutral head posture of experimental group and higher in the artificial forward head posture of control group than the forward head posture of experimental group. Conclusion : In conclusion, neutral head posture is considered to be an important factor in correct posture and improvement of lung function and continuous study of posture correction program for posture imbalance will be needed.

• Bulletin of the Korean Chemical Society
• /
• v.27 no.4
• /
• pp.539-544
• /
• 2006

Proton transfer reactions and ion-molecule reactions of bifunctional ethanes of $H_2NCH_2CH_2NH_2$, $H_2NCH_2CH_2OH$, and $HOCH_2CH_2OH$ were studied using Fourier transform mass spectrometry (FTMS). The rate constants for proton transfer reactions between the fragment ions and neutral molecules were obtained from the temporal variation of the ion abundances. The rate constants were consistent with the heats of reaction. The fastest proton transfer reactions were the reactions of $CH_2N^+$, $CHO^+$, and $CH_3O^+$ for $H_2NCH_2CH_2NH_2$, $H_2NCH_2CH_2OH$, and $HOCH_2CH_2OH$, respectively. The $[M+13]^+$ ion was formed by the ion-molecule reaction between $H_2C=NH_2 ^+$ or $H_2C=OH^+$ and the neutral molecule. The major product ions generated from the ion-molecule reactions between the protonated molecule and neutral molecule were $[2M+H]^+$, $[M+27]^+$, and $[M+15]^+$.

• Structural Engineering and Mechanics
• /
• v.72 no.4
• /
• pp.479-489
• /
• 2019

The corrosion of reinforcement leads to a gradual decay of structural strength and durability. Several models for crack occurrence prediction and crack width propagation are investigated in this paper. Analytical and experimental models were used to predict the bond strength in the period of corrosion propagation. The manner of flexural strength loss is calculated by application of these models for different scenarios. As a new approach, the variation of the concrete beam neutral axis height has been evaluated, which shows a reduction in the neutral axis height for the scenarios without loss of bond. Alternatively, an increase of the neutral axis height was observed for the scenarios including bond and concrete section loss. The statistical properties of the parameters influencing the strength have been deliberated associated with obtaining the time-dependent bending strength during corrosion propagation, using Monte Carlo (MC) random sampling method. Results showed that the ultimate strain in concrete decreases significantly as a consequence of the bond strength reduction during the corrosion process, when the section reaches to its final limit. Therefore, such sections are likely to show brittle behavior.

• Structural Engineering and Mechanics
• /
• v.54 no.5
• /
• pp.923-936
• /
• 2015

In this paper, a simple n-order refined theory based on neutral surface position is developed for bending and frees vibration analyses of functionally graded beams. The present theory is variationally consistent, uses the n-order polynomial term to represent the displacement field, does not require shear correction factor, and gives rise to transverse shear stress variation such that the transverse shear stresses vary parabolically across the thickness satisfying shear stress free surface conditions. The governing equations are derived by employing the Hamilton's principle and the physical neutral surface concept. The accuracy of the present solutions is verified by comparing the obtained results with available published ones.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.8
• /
• pp.2348-2352
• /
• 2013

We report a simple electrochemical approach in fabricating multiple colored molybdenum (Mo) oxide bronzes on the surface of a Mo-quartz electrode. A three step electrochemical batch process consisting of linear sweep voltammetry and anodic oxidation followed by cathodic reduction in neutral $K_2SO_4$ electrolyte at different end potentials, viz. -0.62, -0.80 and -1.60 V (vs. $Hg/HgSO_4$) yielded red, blue and yellow colored bronzes. The samples produced were analyzed by XRD, EDS, and SIMS. The color variation was suggested to be associated with the cations intercalation into the oxide formed and the simultaneous structural changes that occurred during the cathodic reduction in neutral aqueous medium.

• Korean Journal of Materials Research
• /
• v.23 no.11
• /
• pp.661-665
• /
• 2013

We investigated the characteristics of electroless plated Cu films on screen printed Ag/Anodized Al substrate. Cu plating was attempted using neutral electroless plating processes to minimize damage of the anodized Al substrate; this method used sodium hypophosphite instead of formaldehyde as a reducing agent. The basic electroless solution consisted of $CuSO_4{\cdot}5H_2O$ as the main metal source, $NaH_2PO_2{\cdot}H_2O$ as the reducing agent, $C_6H_5Na_3O_7{\cdot}2H_2O$ and $NH_4Cl$ as the complex agents, and $NiSO_4{\cdot}6H_2O$ as the catalyser for the oxidation of the reducing agent, dissolved in deionized water. The pH of the Cu plating solutions was adjusted using $NH_4OH$. According to the variation of pH in the range of 6.5~8, the electroless plated Cu films were coated on screen printed Ag pattern/anodized Al/Al at $70^{\circ}C$. We investigated the surface morphology change of the Cu films using FE-SEM (Field Emission Scanning Electron Microscopy). The chemical composition of the Cu film was determined using XPS (X-ray Photoelectron Spectroscopy). The crystal structures of the Cu films were investigated using XRD (X-ray Diffraction). Using electroless plating at pH 7, the structures of the plated Cu-rich films were typical fcc-Cu; however, a slight Ni component was co-deposited. Finally, we found that the formation of Cu film plated selectively on PCB without any lithography is possible using a neutral electroless plating process.

• Proceedings of the KSR Conference
• /
• 2009.05a
• /
• pp.1426-1430
• /
• 2009

AC AT feeding method consists return circuits of electric train inserting in parallel between trolly line and feeding line and connecting neutral line to rail and FPW. Due to increasing electric load at feeding system, collecting voltage of train and end voltage are going down. So to increase voltage between trolly line and rail, the usefulness of new autotransformer are considered which variation of short impedance and change of line voltage is simulated with modified winding ratio of autotransformer from 1:1 to variable tab.

• Proceedings of the KSEEG Conference
• /
• 2003.04a
• /
• pp.20-23
• /
• 2003

Low-sulfidation style ore deposits, the major source of Au, Ag, and Hg, are formed from neutral-pH, reduced hydrothermal solutions close to equilibrium with their host rocks. The waters are low-salinity (〈1 wt % NaCl equiv.) but relatively gas rich (1-2 wt % $CO_2$), and are largely meteoric water. However, the contribution of magmatic components to the epithermal system, its temporal importance, and its relation to the source of ore metals are largely controversial. (omitted)

• Korean Journal of Human Ecology
• /
• v.14 no.4
• /
• pp.631-643
• /
• 2005

The purpose of this research is to compare, according to tone variation of a red jacket, the preference of female college students from Korea and the U.S. for coloration in the traditional Korean dress. The results of the research can be summarized as follows: As to a vivid skirt according to tone variation of red jacket, students of both countries showed the different view in the preference for coloration of vivid red skirt and vivid. dark red jacket, and vivid orange skirt and dull red jacket, and vivid yellow skirt and light dull red jacket, and vivid violet skirt and dull red jacket. As to the light skirt according to tone variation of red jacket, student of both countries showed the different view in the preference for coloration of light red skirt and light red jacket, and light orange skirt and light red jacket. As to the dull skirt according to tone variation of red jacket, student of both countries showed the different view in the preference for coloration of dull red skirt and vivid light dull dark red jacket, and dull yellow skirt and light dull red jacket, and dull yellow skirt and light dull red jacket, and dull green skirt and dull red jacket, and dull violet skirt and vivid light dull dark red jacket. As to the dark skirt according to tone variation of red jacket, student of both countries showed the different view in the preference for coloration of dark red skirt and dull dark red jacket, and dark orange skirt and vivid light dull red jacket, and dark yellow skirt and dull red jacket. As to the neutral skirt according to tone variation of red jacket, student of both countries showed the different view in the preference for coloration of white skirt and vivid red jacket, and dark gray skirt and light red jacket.