• International Journal of Highway Engineering
• /
• v.20 no.4
• /
• pp.35-46
• /
• 2018

PURPOSES : The purpose of this study is to compare the lane curing time of natural drying and a lane drying device when painting lines on a highway. METHODS : The painting process was carried out in July 2015 and September 2015, respectively, for the Gimcheon IC - Gimcheon JC. After the painting, measurements were obtained three times at six measurement points located at 20 m intervals on the shoulder line and the dividing line. The curing time was measured for natural drying and drying using a lane drying device, and compared for different pavement types (asphalt, concrete) and paint types (waterborne paint, methyl methacrylate paint). RESULTS : The results of the lane curing time comparison on the highway are as follows. The combination of asphalt and methyl methacrylate paint cured more rapidly during both the natural drying and drying using the lane drying device. Finally, it was cured at least 32.2% and 40.7% faster when using a drying device than in natural drying. CONCLUSIONS : The comparison of lane curing time of the highway showed that the combination of asphalt and methyl methacrylate paint cured more rapidly when using both natural drying and a lane drying device.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.10a
• /
• pp.521-526
• /
• 2002

In this paper, we described about the characteristic evaluation of environment-friendly ceramic paint with calcium-silicate mineral as a main binder. Particularly, we performed discharge of the environmental poisoning materials(e.g. VOCs, heavy metal, etc.), and properties of paint slurry and coating film of the ceramic paint. In the comparison of the ceramic paint with natural paint and mineral paint which were known as our environment-friendly paints, ceramic paint had good characteristics in the environmental safety and properies of wet slurry and dried coating film.

• KIEAE Journal
• /
• v.16 no.3
• /
• pp.83-88
• /
• 2016

Purpose : This study aimed to verify the surface hardness and water repellency of earth paint manufactured with earth, a natural material, and provide the results as basic data for paint made with natural materials. Method : After presenting the accurate manufacturing methods for basic materials for paint, the authors conducted and analyzed experiments to evaluate surface hardness and water repellency, fundamental performance indicators for paint, based on different mixture ratios. From the results of the experiment to assess the surface hardness of flour-based earth paint, we observed high surface hardness only after painting the specimen three times. Since potato starch-based earth paint has higher viscosity than its flour-based counterpart, the former did not paint well on the first occasion, resulting in low surface hardness. After painting two or more times, however, it was observed to have higher surface hardness than flour-based earth paint. Result : It was found that at least three iterations of painting was required to obtain high surface hardness of potato starch-based earth paint. Furthermore, the results of the water resistance experiment of earth paint suggest that the use of environment-friendly finishing materials coupled with boiled linseed oil will mitigate the drawbacks of earth paint. The experiment with one-year-old specimens also demonstrated similar water repellent characteristics, which indicates that the performance will improve once the paint has dried for a sufficient period of time.

• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.1225-1230
• /
• 2008

Recently the building material have been developed with the concept of controlling the indoor environment as well as the concept of emitting contaminants less. So, a lot of products with humidity control characteristics put it on the market. However, objective evaluation to these products doesn't work out. Thus consumers cannot obtain accurate information to these products. Therefore, we selected inorganic paint in the functionality materials and evaluated its humidity control characteristic in this research. We divided by four stages and evaluated this inorganic paint. The 1st and 2nd third experiments were executed on a natural condition and the fourth experiment was executed with humidity had been raised by using the humidifier.

• Journal of Environmental Health Sciences
• /
• v.30 no.5 s.81
• /
• pp.487-492
• /
• 2004

Building materials are composed of very complex chemical compounds, and these indoor building materials discharge very much Volatile Organic Compounds(VOCs). We performed the environmental chamber test to investigate the Total VOCs(TVOCs) emission characteristics and emission factors about chemical and natural coating materials. As the result, we concluded that TVOCs emission are high at initial time and decreased in course of time. Natural paint was low emission level for TVOCs than chemical paint by small chamber test. The TVOCs emission factor-time profile showed a good fit with the results from the measured and predicted value.

• Applied Chemistry for Engineering
• /
• v.28 no.5
• /
• pp.501-505
• /
• 2017

Due to the rapid urbanization and increased population, there is an increase in airtight nature of buildings which causes serious indoor air pollution. Among several indoor air pollutants, volatile organic compounds (VOCs) emitted from paint are of major concern. Therefore, there is an urge for the development of environmental friendly paint products. In this wok, a natural wall paint (NWP) was prepared by utilizing a natural clay material "sericite" as a main component. A small chamber test was carried out to identify the toxic substances release from NWP and the results were compared with two eco-friendly commercial paints. The total VOCs were detected in trace level inside the test chamber and their concentrations were below the recommended indoor air quality standards. Toluene was not detected for NWP, whereas formaldehyde was observed in trace level. The toxicity index results were compared with two commercial paints and found that NWP exhibited less harmful gas emission. Based on certification rating of building materials, NWP can be classified as the first grade of building materials. Due to the above advantages, the use of sericite as a major component in NWP will be a useful technique to maintain the indoor air quality.

• 보존과학연구
• /
• s.21
• /
• pp.119-143
• /
• 2000

The pigments composition and structure of the mural painting at Pongjongsa Kuknakjon is discussed. The structure of inner wall is consisited of Paint layer, Ground divided two layers of yellow and white pigments, Support. In case of outer wall, it is consisted of Paint layer, Ground divided three layers of yellow and green pigments, a layer mixed green pigments and paint layer, Support. As a result of compositon analysis of mural painting pigments at Pongjongsa Kuknakjon using Micro-area X-ray diffraction system, the red pigment on inner wall is consisted of Heamatite($Fe_2O_3$), Magnetite($Fe_3O_4$)of deep black pigment, and Chalcocite($Cu_2S$) of light black pigment. The white pigment on outer wall is consisted of Anglesite($PbSO_4$) and Atacamite($Cu_2CI(OH)_3$) of green pigment. We found out that natural pigments painted in the mural painting at Pongjongsa Kuknakjon has kept up its own color for a long time due to using the natural pigment not to artificial synthetic pigment.

• Journal of Applied Reliability
• /
• v.1 no.2
• /
• pp.79-93
• /
• 2001

Recently, new aspects of paints such as a beautiful appearance, use of environmentally friendly paints, etc., in addition to the superior performance of paints have been requested for industrial paints including the paints for heavy construction equipment and others. Particularly, the quality of appearance of coating affects the sales of heavy construction equipment. And the necessity for the paints to have a superior weather-proof property without changing the luster or color even after long-time exposure to the open air is emphasized. The change in the surface color and luster of the paint due to the natural environment progresses very slowly, and it takes a long time to verify material properties when developing new paints. In order to improve such methods, weathering tests are performed in many laboratories as a test for accelerating aging of coating, and the lifetime of the products is estimated through evaluation of the weathering (environment-proof) quality of paints. However, not a great deal of research activity has been conducted up to the present time since the interrelationship between the actual results of testing and field data is different for each paint and it takes a long time to study relevant materials. Therefore, introduced in the present study is the estimation of the change in the quality of appearance of coating in the field through the accelerated aging test among the cases of improvement of the quality of appearance of the urethane paint for heavy construction equipment.

• Natural Product Sciences
• /
• v.4 no.3
• /
• pp.161-169
• /
• 1998

The analogues of lichen components showing anti-tyrosinase activities were synthesized. 4-Alkylresorcinol derivatives showed both the inhibitory activity and cytotoxicity in B-16 melanoma cells at the doses of 10 mM to 1.2 mM. Resorcinol and 4-methylresorcinol showed the inhibitory effect with a low cytotoxicity at the doses of 2.5 mM and $600\;{\mu}M$ among 4-alkylresorcinols, respectively. Some diphenylmethane derivatives (Type A, B, and C) had strong activities with a low cytotoxicity. While xanthine derivatives had no effect. Glucosides of 4,5-alkylresorcinol and the diphenylmethane derivative (Type B) were prepared to decrease the cytotoxicity. As a result, no effect were observed. Liposome of the diphenylmethane derivative (Type B) was prepared for the same purpose, and the latter showed a remarkable effect at the dose of $15\;{\mu}M$ with a low cytotoxicity.

• Journal of the Korean Wood Science and Technology
• /
• v.35 no.4
• /
• pp.45-51
• /
• 2007

To investigate the drying behaviors of the water-based natural coating made by rosin during drying, the mass transfer and optical change from speckle image and speckle rate were measured and the relationship between two analysis methods were investigated. At a linear scale, the speckle rate measured by HORUS related with the mass transfer of coating during drying, and the speckle rate at a log scale was included not only drying time, but also drying mechanism of coating during drying. Therefore, the HORUS was an available method to investigate the drying time and drying mechanism of coating during drying.