• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.10a
• /
• pp.147-150
• /
• 1999

Glossing Exposure Concrete is a high quality architectural concrete, i.e., appearance of natural stone and a marbling effect concrete to achieve high quality glassy reflective surface for outer wall of the building. In this study to obtain the conservation and durability of gloss of the "glossing exposure concrete" we developed a from practice and the best mix proportion and derived the optimistic removal time of form to bring out the durable glassy reflective surface and durable concrete. Hereby with the "glossing exposure concrete" obtained, we investigate the accelerate carbonation and accelerate durability test to evaluate the durability factor of this type of concrete.is type of concrete.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.05a
• /
• pp.643-648
• /
• 2002

A research for recycling the demolished-concrete as concrete aggregate has been concerned in all over the world. There, however, are some problems that qualities of recycled aggregates are not only largely different, but also mechanical properties of recycled aggregate concrete decrease a little in comparison with that of natural aggregate concrete. In this study, the resistance of freezing and thawing of concrete using source-concrete recycled aggregate(SRN) and demolished-concrete recycled aggregate(DRA) was investigated. Futhermore a research for improvement of freeze and thaw durability of recycled aggregate concrete was performed. Relative dynamic modulus of elasticity of SRN and DRA recycled aggregate concrete was dropped 60% before 150 of freezing and thawing cycle, and was much lower than that of control concrete. Relative dynamic modulus of elasticity of recycled aggregate concrete was increased to decrease water-cement ratio, but the freeze and thaw durability of recycled aggregate concrete was not enough improved. Futhermore, when metakaolin and silica fume were repalced, the freeze and thaw durability of recycled aggregate concrete containg metakaolin was more improved than that of silica fume.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.6 s.237
• /
• pp.804-808
• /
• 2005

A pneumatic tire is made up of many flexible filaments of high modulus cord of natural textile, synthetic polymer, glass fiber, or fine hard drawn steel embedded in and bonded to a matrix of low modulus polymetric material. Adhesion property of these materials is very important in tire durability safety because belt-leaving-belt tread separation reduces the ability of a driver to control a vehicle, whether or not the separation is accompanied by a loss of air. In this study adhesion test of carcass-belt-tread is conducted on material properties of 5 PCR tire model, which are on sale in domestic market and analyzed adhesion properties. For those tire models FMVSS 109 indoor high speed durability test is conducted to analyze the correlation between adhesion force and high speed performance of tires and found the correlation between the two test results.

• Textile Coloration and Finishing
• /
• v.16 no.2
• /
• pp.41-46
• /
• 2004

We have studied on the experimental variables such as optimum adsorption condition, color changes, light fastness, antimicrobial properties, and wash durability of the cotton fabrics treated with gallnut extracts. Treatment of gallnut extracts on the cotton fabrics was optimally achieved at 6$0^{\circ}C$ for 60min. Gallnut extracts did not cause unintended color change after treatment on the cotton fabrics dyed with reactive dyes. The cotton fabrics treated with gallnut extracts showed good light fastness, though we took into the account the extract is a natural material. The cotton fabrics treated with 10.0% o.w.f. of gallnut extracts had strong antimicrobial activity and good wash durability.

• Resources Recycling
• /
• v.16 no.6
• /
• pp.20-27
• /
• 2007

This paper presents a detailed experimental study on the durability properties of mortar matrix made with two kind of recycled fine aggregates(RAA, RAB) and five replacement levels (0, 25, 40, 75 and 100) of the recycled fine aggregates as a partial replacement of natural fine aggregate (NA). The durability properties of mortar matrix was evaluated using compressive strength, chloride ion ingress, sulfate attack and carbonation. The test results indicated that the water absorption and Adhered mortar of the recycled fine aggregate was a major factor controlling durability properties. Hereafter, when using built recycled fine aggregate is expected, appropriate removal Adhered mortar and reasonable replacement ratio of recycled fine aggregates was 25% weight of cement are advised to apply to the concrete materials.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.6
• /
• pp.52-59
• /
• 2013

In this study, strength and durability are investigated using structural and vibration analyses on models 1 and 2 of a press in common use. Model 1 has a structure in which a punch is applied from the upper part to the lower part; however, model 2 a structure in which a punch is applied from the lower part to the upper part. Maximum displacements of models 1 and 2 are 0.018184 mm and 0.025498 mm, respectively. Maximum equivalent stresses of models 1 and 2 are 14.144 MPa and 18.58 MPa respectively. Maximum displacements are shown for the punches of both models; model 1 has less deformation than model 2. Model 1 has more durability than model 2, as determined by an investigation of the structural strength. Using natural frequency analysis, model 1 was found to have maximum deformation in the upper part of punch. Mode1 2 has its maximum deformation in the column part of the body and the upper part of the fixed pin. Using harmonic stress analysis, the maximum deformations were found on the punch part and column part of the body in the cases of models 1 and 2, respectively. As the maximum total deformation and equivalent stress in the case of model 2 are shown to become 40 times those values of model 1, the vibration durability of model 2 can be seen to be weaker than that of model 1.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.10
• /
• pp.1339-1344
• /
• 2010

MSM (Modal Superposition Method) is a technique for analyzing structural durability by taking the vibration characteristics into consideration. In this paper, MSR (Modal Stress Recovery) method, which is similar to MSM, was reviewed to check its validity as a durability analysis method. The MSR method directly calculates the modal displacement time history in multibody dynamics analysis; as a result, the total analysis time is shorter than that of MSM method. We conduct durability analysis using the MSR method and a durability test of a torsion beam axle that is affected by various road loads within the natural frequency of the beam axle. The analysis results for critical location and durability were in good agreement with the respective test results. Therefore, durability analysis using the MSR method is effective in predicting the durability of the structures of various dynamic systems.

• Computers and Concrete
• /
• v.19 no.1
• /
• pp.111-120
• /
• 2017

This study aimed to design the accelerated life testing (ALT) of concrete, which stimulating the special natural environment maximumly. Its evaluation indexes, such as dynamic elastic modulus, mass and ultrasonic velocity were measured, and the variation of relative mass and relative dynamic elastic modulus of concrete were studied. Meanwhile, the microanalysis method was used. Moreover, an exploratory application of the stochastic approach, the Weibull distribution and the lognormal distribution, were made to assess the durability of concrete structures. The results show that the ALT for simulating natural environment is more close to the service process of concrete structure under actual conditions; The relative dynamic elastic modulus can be used as the dominant durability evaluation parameters, because it is more sensitive to the environmental factors compared with the relative quality evaluation parameters; In the course of the concrete deterioration, the destruction of the salt freezing cycle is the dominant factor, supplemented by other factors; Both of those two stochastic approaches can be used to evaluate the reliability of concrete specimens under the condition of ALT; By comparison, The lognormal distribution method is better to describe the reliability process.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.1
• /
• pp.8-15
• /
• 2014

This study investigates structural and vibration analyses for three types of bike frame fork models. As long as the maximum equivalent stresses of these models are lower than the yield stress, the three models are considered to be safe structurally. Type 3, with a maximum equivalent stress of 169.23 MPa, has the lowest stress among the three models and the strongest strength. Types 1, 2 and 3 have natural frequencies lower than 270 Hz. Type 3, with a critical frequency of 118 Hz, has the best durability under vibration among the three models. In order to decrease the vibration transmitted to a bike rider riding on a rough road, the impact due to vibration can be relieved by selecting a Type 3 model from among the three models. The results of this study can be effectively utilized for the design of a bike frame fork as this allows the anticipation and prevention of damage caused by durability issues.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.5
• /
• pp.57-66
• /
• 2013

This study investigates structural and vibration analyses due to the change of bolt Numbers on models 1 and 2 of flange couplings connected with both sides of axis. As maximum equivalent stresses of models 1 and 2 are 122.05 and 102.3 MPa respectively by the basis of bolt, these stresses are within the allowable stress of this model and the safety of bolt design is verified. As maximum equivalent stresses of models 1 and 2 are 196.2 and 196.4 MPa respectively by the basis of body, these stresses are within the allowable stress of this model and the safety of body design is verified. Through natural frequency analysis, maximum displacements of model 1 and 2 are shown at the frequencies of 6565.1 and 6614.9 Hz respectively. Maximum displacements in cases of models 1 and 2 are shown at harmonic frequencies of 7760 and 7840 Hz at real loading conditions. By putting these study results together, the durability of vibration at model 2 with bolt numbers of 8 becomes better than model 1 with bolt numbers of 6. These study results can be effectively utilized with the design on flange coupling by anticipating and investigating prevention and durability against its damage.