• Journal of Adhesion and Interface
• /
• v.8 no.3
• /
• pp.9-15
• /
• 2007

The interfacial evaluation of surface modified Jute fiber/polypropylene (PP) composites before and after hydration was investigated using micromechanical test and dynamic contact angle measurement. The IFSS of alkaline and silane-treated Jute fiber/PP composites increased, whereas after hydration, the IFSS of the untreated, alkaline- and silane-treated Jute fibers/PP composites decreased due to swelled fibrils by water infiltration. The interfacial adhesion of silane treated fiber/PP composites was higher than alkaline-treated or the untreated cases. The surface energies of Jute fiber treated under various conditions were obtained using dynamic contact angle measurement. Especially after hydration, the thermodynamic work of adhesion was calculated by considering water interlayer, which indicated the stability of IFSS between silane treated Jute fiber and PP matrix showing better than others.

• Journal of the Korean Ceramic Society
• /
• v.48 no.1
• /
• pp.94-98
• /
• 2011

A Sn-doped $In_2O_3$ (ITO) nanowire photoelectrode was produced using a simple metal evaporation method at low synthesis temperature (< $540^{\circ}C$). The nanowire electrodes have large surface area compared with that of flat ITO thin film, and show low electrical resistivity of $5.6{\times}10^{-3}{\Omega}cm$ at room temperature. In order to apply ITO nanowires to the photoelectrodes of dye-sensitized solar cell (DSSC), those surfaces were modified by $TiO_2$ nanoparticles using a chemical bath deposition (CBD) method. The conversion efficiency of the fabricated $TiO_2$/ITO nanostructure-based DSSC was obtained at 1.4%, which was increased value by a factor of 6 than one without ITO nanowires photoelectrode. This result is attributed to the large surface area and superior electrical property of the ITO nanowires photoelectrode, as well as the structural advantages, including short diffusion length of photo-induced electrons, of the fabricated $TiO_2$/ITO nanostructure-based DSSC.

• Advances in nano research
• /
• v.8 no.3
• /
• pp.191-202
• /
• 2020

The article brings the study of nonlocal, surface and the couple stress together to apparent the frequency retaliation of FG nanobeams (Functionally graded). For the examination of frequency retaliation, the article considers the accurate spot of neutral axis. This article aims to enhance the coherence of proposed model to accurately encapsulate the significant effects of the nonlocal stress field, size effects together with material length scale parameters. These considered parameters are assimilated through what are referred to as modified couple stress as well as nonlocal elasticity theories, which encompasses the stiffness-hardening and softening influence on the nanobeams frequency characteristics. Power-law distribution is followed by the functional gradation of the material across the beam width in the considered structure of the article. Following the well-known Hamilton's principle, fundamental basic equations alongside their correlated boundary conditions are solved analytically. Validation of the study is also done with published result. Distinct parameters (such as surface energy, slenderness ratio, as nonlocal material length scale and power-law exponent) influence is depicted graphically following the boundary conditions on non-dimensional FG nanobeams frequency.

• KSBB Journal
• /
• v.21 no.5
• /
• pp.360-365
• /
• 2006

The objectives of this study were to develop nano-pore silica particles and to modify its surface for use as an enzyme immobilization matrix. Sol-gel reaction was used to produce silica particles of various nano pore sizes with hydroxyl groups on their surfaces. The surface was modified with aldehyde that was confirmed by fluorescence imaging. Trypsin was covalently immobilized by reductive amination. Surface density of the immobilized trypsin was ca. $350{\mu}g/m^2$, which was approximately 17- and 35-fold higher than those from the surfaces with hydroxyl and amine group, respectively. About 90% of the initial enzyme activity was maintained after the 12th use of repeated use. When compared with the commercial matrices, the nano-pore silica particle was superior in terms of immobilization yield and specific activity. This study suggests the nano porous silica particles can be used as enzyme immobilization matrix for industrial applications.

• Applied Chemistry for Engineering
• /
• v.20 no.4
• /
• pp.402-406
• /
• 2009

$TiO_2$ thin films were surface-modified with atmospheric plasma and their photocatalytic activities were evaluated. The films were deposited on glass plates by dip-coating in a $TiO_2$ sol-gel solution and sintered at various temperatures for various times. Nitrogen plasma was used for the modification and the experiments were carried out varying operational parameters such as discharge power and treatment time. Photocatalytic activity was evaluated based on the degradation efficiency of methylene blue (MB) under irradiation of UV-A and fluorescent light. According to XPS analysis, a little amount of nitrogen was found to be doped in the film surface after the modification. As a result, photocatalytic activity increased under irradiation of UV-A and fluorescent light, especially fluorescent light.

• Journal of the Korean Ceramic Society
• /
• v.41 no.1
• /
• pp.86-91
• /
• 2004

$LiCoO_2$ cathode powders with round particle shaped and nano grain sized of 70-300nm were synthesized by a mechanochemical method. The surface of Li-Co precursor prepared by freeze drying method was modified by $K_2SO_4$ coating and ball milling was used for the coating process. The precursor was crystallized to high temperature form of $LiCoO_2$ at $800^{\circ}C$ and the grain growth was inhibited by the $K_2SO_4$ coating effect. The $K_2SO_4$ coating was not decomposed at $800^{\circ}C$ and prevented the contact in the Li-Co precursor particles. The nano-sized $LiCoO_2$ powder had tetragonal phase and it affected the Li diffusion through the surface of particles. It means that the anode materials for hight performance battery should be satisfied not only small particle size but phase contol on the surface of particles. In this study, the powder characteristics and rate capabilities were compared with a commercial powder and the nano-sized $LiCoO_2$ powder fabricated by the mechanochemical method. And the crucial factor which affects on battery performance was also examined.

• Journal of the Korean Applied Science and Technology
• /
• v.21 no.4
• /
• pp.345-351
• /
• 2004

Highly ordered pure-silica MCM-41 materials possessing well-defined morphology have been successfully prepared with surfactant used as a template. The fabrication of mesoporous silica has received considerable attention due to the need to develop more efficient materials' for catalysis, separations, and chemical sensing. The surface modified MCM-41 was used as anadsorbent for biomolecules. Silica-supported organic groups and DNA adsorption on surface modified MCM-41 were investigated by FT-IR and UV-Vis spectrometer, respectively. The use of MCM-41 as the modification of electrode surfaces were investigated electrochemical properties of metal mediators with biomolecules. The modified ITO electrodes increased peak currents for a redox process of $[Ru(bpy)_3]^{2+}$ relative to the bare electrode. The electrochemical detection of DNA by cyclic voltammetry when the current is saturated in the presence of the mediator appeared more sensitive due to a higher catalytic current on the MCM-41 supported electrodes modified by carboxylic acid functional groups. The carboxyl or amine groups on the surface of MCM-41 interact and react with the $-NH_2$ groups of guanine and backbone, respectively. Highly ordered mesoporous materials with organic groups could find applications as DNA sensors.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.3-23
• /
• 2017

The achievement of tissue engineering can be highly depending on the capability to generate complicated, cell seeded three dimensional (3D) micro/nano-structures. So, various fabrication techniques that can be used to precisely design the architecture and topography of scaffolding materials will signify a key aspect of multi-functional tissue engineering. Previous methods for obtaining scaffolds based on top-down are often not satisfactory to produce complex micro/nano-structures due to the lack of control on scaffold architecture, porosity, and cellular interactions. However, a bioprinting method can be used to design sophisticated 3D tissue scaffolds that can be engineered to mimic the tissue architecture using computer aided approach. Also, in recent, the method has been modified and optimized to fabricate scaffolds using various natural biopolymers (collagen, alginate, and chitosan etc.). Variation of the topological structure and polymer concentration allowed tailoring the physical and biological properties of the scaffolds. In this presentation, the 3D bioprinting supplemented with a newly designed plasma treatment for attaining highly bioactive and functional scaffolds for tissue engineering applications will be introduced. Moreover, various in vivo and in vitro results will show that the fabricated scaffolds can carry out their structural and biological functionality.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2006.06b
• /
• pp.417-421
• /
• 2006

In this study, colloidal Ag solution was spouted on the surface of the inorganic pigment using the hybridizer system and the spray nozzle. Then, the surface of the inorganic pigment was modified by titanium dioxide in order to possess antibacterial ability. Nano-sized colloidal Ag was made by using a seed sol method in this study. It was confirmed that the size of particle per unit weight becomes enlarged, as the addition of $AgNO_{3}$ increased, and as the time of reaction increased, in the manufacturing process of nano-sized colloidal Ag. The antibacterial measurement of the inorganic pigment showed that the growth of fungus was reduced as the reaction time increased. It was measured that the antibacterial activity was excellent at fixed time frame, after the antibacterial ability appeared in $5{\sim}7$ hours of the antibacterial inoculation experiment. The experiment of titanium dioxide's Photocatalyst effect showed $60{\sim}70%$ efficiency in about 80 minute reaction time of the dissolution results regarding measurements of benzene. It was shown that more than 90% of the dissolution efficiency was achieved in the reaction time of about 30 minute.

• Applied Chemistry for Engineering
• /
• v.18 no.1
• /
• pp.17-23
• /
• 2007

For the purpose of antibacterial and photocatalystic deodorization functions, the papermaking inorganic fillers and pigments were surface-modified with Ag nano-colloidal solution and $TiO_2$ by using the hybridization technique. The functional specialty sheets and coating papers were produced with the surface-modified fillers and pigments, and evaluated by halo test and inhibition growth test in their antibacterial and photocatalystic characteristics. For the application of specially produced antibacterial handsheet to the wallpaper usages, the photocatalyst efficiency test of benzene in volatile organic compound dissolution experiment of antibacterial and deodorization function wallpaper showed that the efficiency was 45~50% for 80 min of reaction time and 90% of attained resolution was reached at approximately 30 min of response time.