• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.10a
• /
• pp.749-752
• /
• 2014

The device performance of n-channel MuGFET with different fin width, existence of spacer and channel length has been characterized. Tri-Gate structure(fin number=10) has been used. There are four kinds of Tri-Gate with fin width=55nm with spacer, fin width=70nm with spacer, fin width=55nm without spacer, fin width=70nm without spacer. DIBL, subthreshold swing, Vt roll-off, (above Short Channel Effect)and hot carrier stress degradation have been measured. From the experiment results, short Channel Effect with spacer was decreased, hot carrier degradation with spacer and narrow fin width was decreased. Therefore, layout of LDD structure with spacer and narrow fin width is desirable in short channel effect and hot carrier degradation.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.4
• /
• pp.332-340
• /
• 2023

Crystalline silicon solar cells have attracted great attention for their various advantages, such as the availability of raw materials, high-efficiency potential, and well-established processing sequence. Tunnel oxide passivated contact (TOPCon) solar cells are widely regarded as one of the most prospective candidates for the next generation of high-performance solar cells because an efficiency of 26% has been achieved in small-area solar cells. Compared to n-type TOPCon solar cells, the photo conversion efficiency (PCE) of p-type TOPCon is slightly higher. The highest PCEs of p-type TOPCon and n-type TOPCon solar cells are 26.0% and 25.8%, respectively. Despite the highest efficiency in small-area cells, limited progress has been achieved in p-type TOPCon solar cells for large are due to their lower carrier lifetime and inferior surface passivation with the boron-doped c-Si wafer. Nevertheless, it is of great importance to promoting the p-type TOPCon technology due to its lower price and well-established manufacturing procedures with slight modifications in the PERC solar cells production lines. The progress in different approaches to increase the efficiencies of p-type TOPCon solar cells has been reported in this review article and is expected to set valuable strategies to promote the passivation technology of p-type TOPCon, which could further increase the efficiency of TOPCon solar cells.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.193-193
• /
• 2012

In thin film silicon solar cells, p-i-n structure is adopted instead of p/n junction structure as in wafer-based Si solar cells. PECVD is the most widely used thin film deposition process for a-Si:H or ${\mu}c$-Si:H solar cells. Single-chamber PECVD system for a-Si:H solar cell manufacturing has the advantage of lower initial investment and maintenance cost for the equipment. However, in single-chamber PECVD system, doped and intrinsic layers are deposited in one plasma chamber, which inevitably impedes sharp dopant profiles at the interfaces due to the contamination from previous deposition process. The cross-contamination between layers is a serious drawback of single-chamber PECVD system. In this study, a new plasma process to solve the cross-contamination problem in a single-chamber PECVD system was suggested. In order to remove the deposited B inside of the plasma chamber during p-layer deposition, a high RF power was applied right after p-layer deposition with SiH4 gas off, which is then followed by i-layer, n-layer, and Ag top-electrode deposition without vacuum break. In addition to the p-i interface control, various interface control techniques such as FTO-glass pre-annealing in O2 environment to further reduce sheet resistance of FTO-glass, thin layer of TiO2 deposition to prevent H2 plasma reduction of FTO layer, and hydrogen plasma treatment prior to n-layer deposition, etc. were developed. The best initial solar cell efficiency using single-chamber PECVD system of 10.5% for test cell area of 0.2 $cm^2$ could be achieved by adopting various interface control methods.

• Journal of Sensor Science and Technology
• /
• v.7 no.3
• /
• pp.188-196
• /
• 1998

The sensing and electrical characteristics of $WO_{3}$-based n-type semiconductor gas sensors are investigated. In normal air condition, $TiO_{2}$(4 wt. %)-doped $WO_{3}$-based sensor fabricated without any binder shows the grain boundary ( GB ) potential barrier height of 0.26 V. Sensors fabricated with alumina, PVA and silica sol binders show 0.17, 0.22 and 0.26 V of GB potential barrier height, respectively. In the ambience of 120 ppm $NO_{x}$ concentration, the GB potential barrier height of the sensor fablicated without binder is increased to 0.59 V. The sensors were fabricated with alumina, PVA, silica sol binders show 0.43, 0.66 and 0.52 V of potential barrier, respectively. Thus the variation of the potential barrier at GB is largest in the sensor fabricated with the PVA binder. This is found to be the main reason why the sensor fabricated with the PVA binder shows the best sensitivity. It is also found that the decrease of sensitivity at a temperature higher than the optimum operation temperature is due to the temperature dependence of the sensor resistance in normal air condition rather than the desorption of the adsorbed $NO_{x}$ gas particles. In the ambience of 250 ppm CO concentration, the GB potential barrier heights of the sensors fabricated without binder and with PVA binder are about 0.2 V showing negligible change compared to the case of normal air ambience. This fact indicates that these sensors are good candidates for the selective detection of $NO_{x}$ gas in the mixture of CO and $NO_{x}$ gases.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.177-177
• /
• 2007

ZnO는 3.36eV의 넓은 밴드캡을 가지는 II-IV족 반도체로써 태양전지, LED와 같은 광학적 소자로 이용이 기대가 되는 물질이다. 더욱이, 상온에서의 60meV에 해당하는 큰 엑시톤 에너지와 밴드캡 에지니어링이 가능하다는 장점 때문에 광학적 소자로 널리 이용되고 있는 GaN을 대체할 수 있는 물질로 주목을 받고 있다. 하지만, p-type ZnO는 형성이 어렵고 낮은 이동도와 케리어 농도의 특성을 보이고, 대기 중에 장시간 노출할 경우 n-type ZnO의 특성으로 돌아가는 불안정성을 보이고 있다. 최근에 몇몇의 연구자들에 의해 V족의 원소인 P(phosphorous), N(nitrogen), As(arsenic))를 도핑하여 p-type ZnO의 형성에 대한 논문이 발표되고 있다. 또한, V족 원소 중에 P는 p-type ZnO 형성에 효과적인 도핑 물질로 보고되 고 있다. 본 연구는 마그네트론 스퍼터링을 이용하여 다양한 온도에서 성장된 P도핑 ZnO 박막의 특성에 대해 연구하였다. P도핑된 ZnO 박막은 사파이어 기판에 buffer층을 사용한 Insulator 특성의 ZnO박막위에 400, 500, 600, $700^{\circ}C$에서 성장되 었다. 박막의 특성 분석에는 325nm의 파장을 가지는 He-Cd의 레이져 광원을 사용하여 10K의 저온 PL과 0.5T의 자기장을 사용한 van der Pauw configuration에 의한 Hall effect측정, 그리고 결정성 분석에는 XRD와 TEM을 이용하였다. 상온 Hall-effect 측정 결과, $400{\sim}600^{\circ}C$ 에서 성장된 박막은 n-type의 특성을 보였고, $700^{\circ}C$에서 성장된 Phosphorous 도핑 ZnO박막은 $1.19{\times}10^{17}$의 캐리어 농도를 가지는 p-type의 특성을 보였다. 그리고 XRD분석과 TEM분석을 통하여 박막의 성장온도가 증가 할수록 P도핑된 ZnO박막의 결정성이 향상되는 것을 알 수 있었다. 또한 10K의 저온 PL분석을 통해 p도핑에 의한 액셉터에 관련된 피크들을 관찰할 수 있었다.

• Current Photovoltaic Research
• /
• v.7 no.4
• /
• pp.97-102
• /
• 2019

Bifacial and semitransparent hydrogenated amorphous silicon (a-Si:H) thin-film solar cells in p-i-n configuration were prepared with front and rear transparent conducting oxide (TCO) electrodes using plasma-enhanced chemical vapor deposition method. Fluorine-doped tin oxide and tin-doped indium oxide films were used as front and rear TCO contacts, respectively. Film thickness of intrinsic a-Si:H absorber layers were controlled from 150 nm to 450 nm by changing deposition time. The dependence of performance characteristics of solar cells on the front and rear illumination direction were investigated. For front illumination, gradual increase in the short-circuit current density (J_SC) from 10.59 mA/㎠ to 14.19 mA/㎠ was obtained, whereas slight decreases from 0.83 V to 0.81 V for the open-circuit voltage (V_OC) and from 68.43% to 65.75% for fill factor (FF) were observed. The average optical transmittance in the wavelength region of 380 ~ 780 nm of the solar cells decreased gradually from 22.76% to 15.67% as the absorber thickness was changed from 150 nm to 450 nm. In case of the solar cells under rear illumination condition, the J_SC increased from 10.81 to 12.64 mA/㎠ and the FF deceased from 66.63% to 61.85%, while the V_OC values were maintained at 0.80 V with increasing the absorber thickness from 150 nm to 450 nm. By optimizing the deposition parameters, a high-quality bifacial and semitransparent a-Si:H solar cell with 350 nm-thick i-a-Si:H absorber layer exhibited the conversion efficiencies of 7.69% for front illumination and 6.40% for rear illumination, and average visible optical transmittance of 17.20%.

• Journal of the Korean Ceramic Society
• /
• v.41 no.8
• /
• pp.623-627
• /
• 2004

Phase formation and electrical conduction behavior of Ba-doped LaBaGa $O_4$ layered perovskite were studied. Orthorhombic single phase of $K_2$Ni $F_4$-type structure was observed for the composition range of 0$\leq$x$\leq$0.2 in the La$\_$1＋x/Ba$\_$1＋x/Ga $O_4$$\_$4-$\delta$/ system by X-ray analysis. In the dry atmosphere, La$\_$0.8/Ba$\_$1.2/Ga$\_$3.9/ exhibited mixed conduction of oxygen ion and hole (p-type) at high p( $O_2$). However, in water vapor containing atmosphere, it showed proton conduction due to the incorporation of water into oxygen vacancies. As the temperature decreased, the contribution of proton conductivity to the total conduction increased and proton conduction was dominant below 350$^{\circ}C$. The activation energy for proton conduction was calculated as 0.72 eV.

• Korean Journal of Materials Research
• /
• v.20 no.4
• /
• pp.210-216
• /
• 2010

This paper investigates the dependence of a-Si:H/c-Si passivation and heterojunction solar cell performances on various cleaning processes of silicon wafers. It is observed that the passivation quality of a-Si:H thin-films on c-Si wafers depends highly on the initial H-termination properties of the wafer surface. The effective minority carrier lifetime (MCLT) of highly H-terminated wafer is beneficial for obtaining high quality passivation of a-Si:H/c-Si. The wafers passivated by p(n)-doped a-Si:H layers have low MCLT regardless of the initial H-termination quality. On the other hand, the MCLT of wafers incorporating intrinsic (i) a-Si:H as a passivation layer shows sensitive variation with initial cleaning and H-termination schemes. By applying the improved cleaning processes, we can obtain an MCLT of $100{\mu}sec$ after H-termination and above $600{\mu}sec$ after i a-Si:H thin film deposition. By adapting improved cleaning processes and by improving passivation and doped layers, we can fabricate a-Si:H/c-Si heterojunction solar cells with an active area conversion efficiency of 18.42%, which cells have an open circuit voltage of 0.670V, short circuit current of $37.31\;mA/cm^2$ and fill factor of 0.7374. These cells show more than 20% pseudo efficiency measured by Suns-$V_{oc}$ with an elimination of series resistance.

• Korean Journal of Materials Research
• /
• v.20 no.11
• /
• pp.575-580
• /
• 2010

The microstructure and positive temperature coefficient of resistivity (PTCR) characteristics of 0.1 mol%$Na_2Ti_6O_{13}$ doped $0.94BaTiO_3-0.06(Bi_{0.5}Na_{0.5})TiO_3$ (BBNT-NT001) ceramics sintered at various temperatures from $1200^{\circ}C$ to $1350^{\circ}C$ were investigated in order to develop eco-friendly PTCR thermistors with a high Curie temperature ($T_C$). Resulting thermistors showed a perovskite structure with a tetragonal symmetry. When sintered at $1200^{\circ}C$, the specimen had a uniform microstructure with small grains. However, abnormally grown grains started to appear at $1250^{\circ}C$ and a homogeneous microstructure with large grains was exhibited when the sintering temperature reached $1325^{\circ}C$. When the temperature exceeded $1325^{\circ}C$, the grain growth was inhibited due to the numerous nucleation sites generated at the extremely high temperature. It is considered that $Na_2Ti_6O_{13}$ is responsible for the grain growth of the $0.94BaTiO_3-0.06(Bi_{0.5}Na_{0.5})TiO_3$) ceramics by forming a liquid phase during the sintering at around $1300^{\circ}C$. The grain growth of the BBNT-NT001 ceramics was significantly correlated with a decrease of resistivity. All the specimens were observed to have PTCR characteristics except for the sample sintered at $1200^{\circ}C$. The BBNT-NT001 ceramics had significantly decreased $\tilde{n}_{rt}$ and increased resistivity jump with increasing sintering temperature at from $1200^{\circ}C$ to $1325^{\circ}C$. Especially, the BBNT-NT001 ceramics sintered at $1325^{\circ}C$ exhibited superior PTCR characteristics of low resistivity at room temperature ($122\;{\Omega}{\cdot}cm$), high resistivity jump ($1.28{\times}10^4$), high resistivity temperature factor (20.4%/$^{\circ}C$), and a high Tc of $157.9^{\circ}C$.

• The Journal of Korean Academy of Prosthodontics
• /
• v.58 no.4
• /
• pp.275-281
• /
• 2020

Purpose: Development of a latent antimicrobial soft liner is strongly needed to overcome a possible inflammation related with its dimensional degrade or surface roughness. Modified tissue conditioner (TC) containing chitosan-doped silver nanoparticles (ChSN) complexes were synthesized and assessed for their characterizations. Materials and methods: ChSN were preliminarily synthesized from silver nitrate (AgNO₃), sodium borohydride (NaBH₄) as a reducing agent and chitosan biopolymer as a capping agent. Ultraviolet-visible and Fourier transform infrared spectroscopy were conducted to confirm the stable reduction of nanoparticles with chitosan. Modified TC blended with ChSN by 0 (control), 1.0, 3.0 and 5.0 % mass fraction were mechanically tested by ultimate tensile strength (UTS), silver ion elution and color stability (n=7). Results: At 24 hour and 7 day storage periods, UTS values were not significant (P>.05) as compared with pristine TC (control) and silver ion was detected with the dose-dependent values of ChSN incorporated. Color stability of TC were influenced by ChSN add, with the higher doses, the significantly greater color changes (P<.05). Conclusion: A stable synthesized ChSN was acquired and modified TC loading ChSN was characterized as silver ion releasing without detrimental physical property. For its clinical application, antimicrobial test, color control and multifactor investigations are still required.