• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2000년도 춘계학술대회 논문집
• /
• pp.234-241
• /
• 2000

Stress analysis of the bogie frame by using the finite element method has been performed for the various loading conditions according to the results of vehicle dynamics analysis. Multiaxial fatigue analysis methods such as signed von Mises method, and typical critical plane theories were reviewed, and margin of safety for fatigue is defined. Multiaxial fatigue analysis program to predict the margin of safety of bogie frame under non-proportional loading conditions has been developed by using a commercial command language. Fatigue analysis of bogie frame under multiaxial loading was performed through this program and finite element analysis result. The procedure developed in this study is considered to be useful for the fatigue strength analysis in preliminary design stage of railway components under multiaxial loading condition.

• 콘크리트학회논문집
• /
• 제16권2호
• /
• pp.185-194
• /
• 2004

콘크리트의 크리프에 관한 기존의 연구결과들은 대부분 1축응력이 가해지는 경우에 대한 것으로 콘크리트 구조물 또는 부재가 다축응력 상태에 놓이는 경우에 적용하기가 어려운 점이 있다. 따라서 다축응력 상태의 콘크리트 크리프 특성에 관한 연구가 필요하다. 이 연구에서 다축응력 상태에 놓인 콘크리트의 크리프 특성을 실험을 통해 파악하였다. 세 가지 서로 다른강도를 갖는 배합의 콘크리트에 대해 각각 9개의 실험체를 제작하였으며, 1축, 2축, 3축 응력 상태에서 크리프 실험을 실시하였다. 하중이 가해지는 세 방향에서 시간에 따른 변형률을 측정하였다. 가압시점의 푸아송비와 크리프변형에 기인한 푸아송비 그리고 탄성변형과 크리프변형에 기인한 푸아송비를 구하였으며, 각 콘크리트에 대한 세 가지 푸아송비는 근사적으로 같은 것으로 나타났다. 가압시점의 푸아송비와 전체 변형에 대한 푸아송비는 콘크리트 강도의 증가에 따라 다소 증가하는 경향을 보였으며, 각 푸아송비는 응력상태에 따라 특정한 경향을 나타내지 않았다. 체적성분의 응력과 크리프변형률, 편차성분의 응력과 크리프변형률은 선형의 관계를 나타내었다.

• 한국정밀공학회지
• /
• 제24권4호
• /
• pp.123-130
• /
• 2007

Recently, a lot of work and interest have been devoted to the development of multiaxial fatigue parameters for fretting fatigue life prediction. In this study, the fretting fatigue lift and critical location ware estimated and evaluated through the multiaxial fatigue theories in a cylinder-on-flat contact configuration far Cr-Mo steel, SCM420, the material commonly is used in gears of the automobile and rollers of the conveyor. The strain-life curve was obtained from fatigue test for SCM420. The Fretting fatigue life and critical location were estimated through stress distributions, SWT-parameters and FS-parameters obtained from FEA. This paper showed possibility of applying multiaxial fatigue theories to fretting fatigue lift prediction comparing predicted life with experimental results.

• 대한기계학회논문집
• /
• 제15권2호
• /
• pp.413-423
• /
• 1991

Multiaxial loading by combinations of tension-torsion-internal pressure have been applied to the thins-walled tubular specimens prepared from cold drawn tubes of SAE 1020 steel. Prior to the multiaxial loading, each specimen has been twisted to different shear strains. Uniaxial tensile yield stresses measured at different angles to the tube axis clearly show that the initial orthotropic symmetry is maintained during twisting. The orthotropy axes are observed to rotate with shear strains. The plane stress yield locus measured for each twisted specimens show that yield surface shape does not remain similar during twisting and thus anisotropic work hardening is not a function of only plastic work.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집A
• /
• pp.316-321
• /
• 2000

The role of fatigue on the surface damage of 5% chrome cold milling work roll is evaluated. Uniaxial and torsional fatigue tests are carried out, and the baseline data for fatigue life evaluation are established. An appropriate multiaxial fatigue parameter is developed from the fatigue data. Fatigue tests are also performed under compressive mean stresses, and a mean stress model is formulated. A computer program is developed to assess the interaction of fatigue and grinding of the roll. The fatigue damage is computed for selected servicing conditions. It is found that the fatigue damage can be an important issue when the effect of mean stress is ignored, however the fatigue damage is negligibly small when the effect of mean stress including the residual stresses currently used is fully accounted. The result indicates that spalling due to the growth of thermal shock cracks is more important than fatigue damage in roll surface failure.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집A
• /
• pp.137-142
• /
• 2001

In structural applications, brittle materials such as soda-lime glasses and ceramics are often subjected to multiaxial stress. Brittle materials with crack or damaged by foreign object impacts are abruptly fractured from cracks, because of their properities of very high strength and low fracture toughness. But in most cases, the residual strength has been derived from tests under uniaxial stress such as a 4-point bend test. The strengths under multiaxial stresses might be different from the strength. In comparable tests, the residual strength under biaxial stress state by the ball-on-ring test was greater than that under the uniaxial one by the 4-point bend test. In the case that crack having 90deg. to loading direction, the ratio of biaxial to uniaxial flexure strength was 1.12. At a different crack angle to loading direction when it was evaluated by the 4-point bend test, the residual strength was different and the ratio of 45deg. to 90deg. was 1.16.

• 대한기계학회논문집A
• /
• 제26권5호
• /
• pp.932-938
• /
• 2002

In structural applications, brittle materials such as soda-lime glasses and ceramics are usually subjected to multiaxial stress state. Brittle materials with cracks or damage by foreign object impacts are apt to fracture abruptly from cracks, because of their properities of very high strength and low fracture toughness. But in most cases, the residual strength of structural members with damage has been tested under uniaxial stress condition such as the 4-point bend test. Depending upon the crack pattern developed, the strength under multiaxial stress state might be different from the one under uniaxial. A comparative study was carried out to investigate the influence of stress state on the residual strength evaluation. In comparable tests, the residual strength under biaxial stress state by the ball-on-ring test was greater than that under the uniaxial one by the 4-point bend test, when a small size indendation crack was introduced. In the case that crack having an angle of 90deg. to the applied stress direction, the ratio of biaxial to uniaxial flexure strength was about 1.12. The residual strength was different from crack angles to loading direction when it was evaluated by the 4-point bend test. The ratio of residual strength of 45deg. crack to 90deg. one was about 1.20. In the case of specimen cracked by a spherical impact, it was shown that an overall decrease in flexure strength with increasing impact velocity, and the critical impact velocity for formation of a radial and/or cone crack was about 30m/s. In those cases that relatively large cracks were developed as compared with the case of indented cracks, the ratio of residual strength under biaxial stress state to one uniaxial became small.

• Structural Engineering and Mechanics
• /
• 제35권5호
• /
• pp.571-592
• /
• 2010

An energy-based fatigue life prediction framework was previously developed by the authors for prediction of axial, bending and shear fatigue life at various stress ratios. The framework for the prediction of fatigue life via energy analysis was based on a new constitutive law, which states the following: the amount of energy required to fracture a material is constant. In the first part of this study, energy expressions that construct the constitutive law are equated in the form of total strain energy and the distortion energy dissipated in a fatigue cycle. The resulting equation is further evaluated to acquire the equivalent stress per cycle using energy based methodologies. The equivalent stress expressions are developed both for biaxial and multiaxial fatigue loads and are used to predict the number of cycles to failure based on previously developed prediction criterion. The equivalent stress expressions developed in this study are further used in a new finite element procedure to predict the fatigue life for two and three dimensional structures. In the second part of this study, a new Quadrilateral fatigue finite element is developed through integration of constitutive law into minimum potential energy formulation. This new QUAD-4 element is capable of simulating biaxial fatigue problems. The final output of this finite element analysis both using equivalent stress approach and using the new QUAD-4 fatigue element, is in the form of number of cycles to failure for each element on a scale in ascending or descending order. Therefore, the new finite element framework can provide the number of cycles to failure at each location in gas turbine engine structural components. In order to obtain experimental data for comparison, an Al6061-T6 plate is tested using a previously developed vibration based testing framework. The finite element analysis is performed for Al6061-T6 aluminum and the results are compared with experimental results.

• 소성∙가공
• /
• 제20권3호
• /
• pp.222-228
• /
• 2011

This paper is a review of biaxial tensile test equipments and specimens. The stresses acting on a component in service are multiaxial in nature. Therefore, it is necessary to consider the mechanical properties of sheet materials not only under uniaxial but also under these multiaxial stress states. Biaxial testing of metal in industry becomes an important investigation tool for the evaluation of mechanical properties of sheet metals. In this paper, several types of biaxial tensile tests were reviewed, and their advantages and limitations were discussed.

• International Journal of Automotive Technology
• /
• 제6권3호
• /
• pp.285-291
• /
• 2005

In this paper, the author proposes a fatigue damage parameter of spot welded joints under proportional loading. The proposed fatigue damage parameter is developed based on von Mises' equivalent stress and local structural stress at the edge of spot weld nugget. The structural stress at the edges of the weld nugget in each sheet is calculated using the forces and moments that are determined by finite element analysis. A structural equivalent stress is then calculated by von Mises' equivalent stress equation. The structural equivalent stresses are correlated to experimental fatigue life of the spot welded joints. The proposed parameter is evaluated with fatigue test data of spot welds subjected to multi axial and tensile-shear loads. Sheppard's parameter and Rupp and co-workers' parameter are also evaluated with the same test data to compare with the author's parameter. This proposed parameter presents a better correlation with experimental fatigue data than those of Sheppard's and Rupp and co-workers' parameter. The proposed parameter should be very effective for durability calculations during the early design phase since coarsely meshed finite element models can be employed.