• Journal of the Korean Association of Geographic Information Studies
• /
• v.17 no.4
• /
• pp.28-39
• /
• 2014

Several studies have been performed globally on the construction of integrated systems that are available for the integrated use of 3D geographic information on terrain and oceans. Research on 3D geographic modeling is also facilitated by the application of Lidar surveying, which enables the highly accurate realization of 3D geographic information for a wide area of land. In addition, a few marine research organizations have been conducting investigations and surveying diverse ocean information for building and applying MGIS(Marine Geographic Information System). However, the construction of integrated geographic information systems for both terrain and oceans has certain limitations resulting from the inconsistency in reference systems and datum levels between two data. Therefore, in this investigation, integrated geospatial information has been realized by using a combined topographical map, after matching the reference systems and datum levels by integration of airborne Lidar data and multi-beam echo sounder data. To verify the accuracy of the integrated geospatial information data, ten randomly selected samples from study areas were selected and analyzed. The results show that the 10 analyzed data samples have an RMSE of 0.46m, which meets the IHO standard(0.5m) for depth accuracy of hydrographic surveys.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.8
• /
• pp.2648-2656
• /
• 2011

A simple HPLC-DAD method was developed and validated to determine B group vitamin content (thiamine, riboflavin, nicotinamide, pantothenic acid, pyridoxine and folic acid) in supplemented food samples, i.e., infant formula, cereal, low-calorie food, a multi-vitamin pill and a vitamin drink. In this study, the most significant advantages were simultaneous determination of the six B group vitamins in various food matrices and a small number of sample treatment steps that required only an organic solvent, acetonitrile. Moreover, this method prevents reduction of column durability, because the mobile phase does not contain ion-pairing reagents. Analytes were separated on a Develosil RPAQUEOUS $C_{30}$ (4.6 mm ${\times}$ 250 mm, 5 ${\mu}M$ particle size) column with a gradient elution of acetonitrile and 20 mM phosphate buffer (pH 3.0) at a flow rate between 0.8 and 1.0 mL/min. Detection was performed at 275 nm, except for that of pantothenic acid (205 nm). The calibration curves for all six vitamins showed good linearity with correlation coefficients ($r^2$) higher than 0.995. The developed method was validated with respect to linearity, intra- and inter-day accuracy and precision, limit of quantification (LOQ), recovery and stability. The method showed good precision and accuracy, with intra- and inter-assay coefficients of variation less than 15% at all concentrations. The recovery was carried out according to the standard addition procedure, with yields ranging from 89.8 to 104.4%. This method was successfully applied to the determination of vitamin B groups in supplemented food products.

• The Journal of Korean Academic Society of Nursing Education
• /
• v.9 no.2
• /
• pp.288-297
• /
• 2003

This study was attempted to find out the actual conditions about drug education among the elementary school teachers. Subjects consisted of nurse-teachers 175, class-room teachers 240 and athletics teachers 53 at the elementary schools in Pusan city. The data collecting period was December 23th through December 28th, 2002 and the collected data were analyzed by SPSSWIN 10.0 program using frequency, percentage, mean, standard deviation and $x^2$-test. The results of this study were as follows: 1. The importance of the drug education in special curriculum has been agreed with 96.0% of nurse-teachers, 90.4% of classroom teachers and 92.4% of athletics teachers. 2. For the drug education, nurse-teachers used to get information through the professional knowledge books(61.1%), and internet (33.1%), on the other hand class-room teachers(80.0%) and athletics teachers (48.9%) used to get information from various media. 3. Until now, the drug education has been performed by 80.6% of nurse-teachers, 34.2% of class-room teachers and 41.5% of athletics teachers. After drug education, the results of self-evaluation showed that 73.8% of nurse-teachers and 51.9% of athletics teachers were satisfied with it, but 69.5% of class-room teachers were not. In terms of the education methodology, most nurse-teachers(85.8%) usually used both verbal lecture and multi-media materials for teaching, but class-room teachers(97.8%) and athletics teachers(81.8%) just gave the verbal lecture. 4. About practical difficulties of drug education, the biggest problem was the absence of no systematic curriculum for nurse-teachers(22.9%), the insufficient expert knowledge for class-room teachers (26.3%) and a lack of education materials for athletics teachers(37.7%). The subjects were responded that the well-qualified personnel in charge of drug education in elementary school were nurse-teachers (52.0%) or nurse-teachers and class-room teachers.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.39 no.4
• /
• pp.355-355
• /
• 2002

In this paper, we designed a FPU(floating point unit) that it is very important and requires of high density when digital audio is designed. Almost audio system must support the multi-channel and required for high quality. A floating point arithmetic function in MPEG-2 AAC that implemented by hardware is able to realtime decoding when DSP realization. The reason is that MPEG-2 AAC is compatible to the Audio field of MPEG-4 and afterwards. We designed a FPU by hardware to increase the speed of a floating point unit with much calculation part in the MPEG-2 AAC Decoder. A FPU is composed of a multiplier and an adder. A multiplier used the Radix-4 Booth algorithm and an adder adopted 1's complement method for speed up. A form of a floating point unit has 8bit of exponent part and 24bit of mantissa. It's compatible with the IEEE single precision format and adopted a pipeline architecture to increase the speed of a processor. All of sub blocks are based on ISO/IEC 13818-7 standard. The algorithm is tested by C language and the design does by use of VHDL(VHSIC Hardware Description Language). The maximum operation speed is 23.2MHz and the stable operation speed is 19MHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.11 s.102
• /
• pp.1075-1085
• /
• 2005

The purpose of this paper is to design the architecture for synchronization of MB-OFDM UWB system that is being processed the standardization for Alt-PHY of WPAN(Wireless Personal Area Network) at IEEE802.15.3a and to analyze the implementation loss due to 4 parallel synchronization architecture for design or link margin. First an overview of the MB-OFDM UWB system based on IEEE802.15.3a Alt-PHY standard is described. The effects of non-ideal transmission conditions of the MB-OFDM UWB system including carrier frequency offset and sampling clock offset are analyzed to design a full digital architecture for synchronization. The synchronization architecture using 4-parallel structure is then proposed to consider the VLSI implementation including algorithms for carrier frequency offset and sampling clock offset to minimize the effects of synchronization errors. The overall performance degradation due to the proposed synchronization architecture is simulated to be with maximum 3.08 dB of the ideal receiver in maximum carrier frequency offset and sampling clock offset tolerance fir MB-OFDM UWB system.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.22 no.4
• /
• pp.337-346
• /
• 2020

Traffic jam and congestion in urban areas has caused the need to improve the utility of underground space. In response, research on underground structures is increasingly being conducted. Notably, a double-deck tunnel is one of the most widely used of all those underground structures. This double-deck tunnel is separated by the middle slab into the upper and lower roadways. Both vehicle load and earthquake load cause the middle slab to exhibit dynamic behavior. Earthquake-related response characteristics, in particular, are highly complex and difficult to interpret in a theoretical context, and thus experimental research is required. The aim of the present study is to assess the stability of a double-deck tunnel's middle slab of the Collapse Prevention Level and Seismic Category 1 with regard to the presence of vibration-damping Rubber Bearings. In vibration table tests, the ratio of similitude was set to 1/4. Linings and vibrating platforms were fixed during scaled model tests to represent the integrated behavior of the ground and the applied models. In doing so, it was possible to minimize relative behavior. The standard TBM cross-section for the virtual double-deck tunnel was selected as a test subject. The level of ground motion exerted on the bedrock was set to 0.154 g (artificial seismic wave, Collapse Prevention Level and Seismic Category 1). A seismic wave with the maximum acceleration of 0.154 g was applied to the vibration table input (bedrock) to analyze resultant amplification in the models. As a result, the seismic stability of the middle slab was evaluated and analyzed with respect to the presence of vibration-damping rubber bearings. It was confirmed that the presence of vibration-damping rubber bearings improved its earthquake acceleration damping performance by up to 40%.

• The Journal of the Acoustical Society of Korea
• /
• v.23 no.8
• /
• pp.554-561
• /
• 2004

As the technologies of semiconductor and multimedia communication have been improved. the high-quality video and the multi-channel audio have been highlighted. MPEG Audio Layer 3 decoder has been implemented as a Processor using a standard. Since the synthesis filter of MPEG-1 Audio Layer 3 decoder requires the most outstanding operation in the entire decoder. the synthesis filter that can reduce the amount of operation is needed for the design of the high-speed processor. Therefore, in this paper, the synthesis filter. the most important part of MPEG Audio, is materialized in FPGA using the method of DAULT (distributed arithemetic look-up table). For the design of high-speed synthesis filter, the DAULT method is used instead of a multiplier and a Pipeline structure is used. The Performance improvement by 30% is obtained by additionally making the result of multiplication of data with cosine function into the table. All hardware design of this Paper are described using VHDL (VHIC Hardware Description Language) Active-HDL 6.1 of ALDEC is used for VHDL simulation and Synplify Pro 7.2V is used for Model-sim and synthesis. The corresponding library is materialized by XC4013E and XC4020EX. XC4052XL of XILINX and XACT M1.4 is used for P&R tool. The materialized processor operates from 20MHz to 70MHz.

• Journal of the Korean Chemical Society
• /
• v.43 no.2
• /
• pp.193-198
• /
• 1999

The transfection efficiency of plasmid DNA was inspected using multi-cationic polymer, 5, 10, 25 and 50KD polyethylenimine (PEI). The optimal neutralization ratio of PEI/DNA complexes by agarose assay was 1.5-2.0 (nmol/nmol) without much difference in molecular weight of PEI.In vitro transfection assay, most of PEI-mediated plasmid delivery was better compared to the naked DNA. Especially, 25KD PEI at optimal condition gave higher transfection rather than the standard assay of DEAE-dextran or Lipofectin. To enhance the cell targeting delivery, the liposome formulations were introduced using phospholipids. As a result, PC/PE liposomes increased 2-2.5 times of the transfection efficiency of PEI single or PC/PE single delivery, but not the case of 25KD PEI. Moreover, the DOTAP/PE-introduced PEI delivery reduced the transfection of DOTAP/PE single delivery. All these results proved that the PEI can be used not only good transfectants and but also good DNA condensing agents in neutral/anionic liposome for cell targeting delivery.

• Economic and Environmental Geology
• /
• v.30 no.1
• /
• pp.51-60
• /
• 1997

The high radon (Rn222) potentials of soil, groundwater, hotspring and indoor environments in the Taejon city area were delineated by use of an EDA RDA-200 radon detector. The U and Th contents were also analysed using a Multi Channel Analyzer to illustrate the sources of the radon potentials. The average U concentrations in Taejon vary according to the type of granites such as $4.14{\pm}2.36ppm$ in schistose granite (SG), $3.13{\pm}1.70ppm$ in biotite granite (BG) and $3.01{\pm}1.95ppm$ in two mica granite (TG). The U contents in the granites are closely related with the amounts of uraniferous minerals. However, the U contents in the soil are found to be $5.05{\pm}4.75ppm$ in TG, $4.07{\pm}1.69ppm$ in BG and $3.87{\pm}1.91ppm$ in SG which are mainly explained by the different cation exchange capacities (CEC) of the soils from various granites. The levels of soil radon are $552{\pm}656pCi/l$ in SG, in which levels at two locations exceed the level of 1,350 pCi/l established as guideline for follow-up action by the U.S. Environmental Protection Agency (EPA), $443{\pm}284pCi/l$ in TG and $224{\pm}115pCi/l$ in the BG. The soil radon concentrations are found to be proportional to the U content and hardness of the soils. The groundwater radon concentrations in the domestic wells of - 30~-100 m depth show that $6,907{\pm}4,665pCi/l$ in TG, $5,503{\pm}6,551pCi/l$ in SG and $2,104{\pm}1,157pCi/l$ in BG which are positively related with U contents in soils. The radon levels of six groundwater wells in TG and two in SG are greater than guideline for drinking water level, 10,000 pCi/l by EPA (1986). Average radon contents of hotsprings and public bathes in the TG area are $7,071{\pm}1,942pCi/l$ and $1,638{\pm}709pCi/l$, respectively, which are below the EPA standard for remedial action value of the 10,000 pCi/l. The mean indoor radon concentrations of the TG and SG areas are $1.60{\pm}1.20pCi/l$ and $1.60{\pm}0.70pCi/l$, respectively. The elevated indoor radon levels of 5.6 pCi/l and 6.7 pCi/l are found to be particularly in TG area, which exceeds 4 pCi/i guideline, correlating positively with the U contents in the soil and radon concentration in the groundwater.

• Applied Chemistry for Engineering
• /
• v.31 no.4
• /
• pp.443-451
• /
• 2020

In this study, the physico-chemical properties and pyrolysis kinetics of livestock mature solid fuel were investigated to know its feasibility as a fuel. Ultimate and proximate analysis results showed that livestock mature solid fuel has high contents of volatile matter (64.94%), carbon (44.35%), and hydrogen (5.54%). The low heating value of livestock mature solid fuel (3880 kcal/kg) was also higher than the standard requirement of solid fuel (3000 kcal/kg). Thermogravimetic analysis results indicated that livestock mature solid fuel has three decomposition temperature regions. The first temperature zone (130~330 ℃) was consisted with the vaporization of extracts and the decomposition of hemicellulose and cellulose. The second (330~480 ℃) and third (550~800 ℃) temperature regions were derived from the decomposition of lignin and additional decomposition of carbonaceous materials, respectively. The activation energy derived from model free kinetic analysis results including Friedman, Flynn-Wall-Ozawa (FWO), and Kissinger-Akahira-Sunose (KAS) methods for the pyrolysis of livestock mature solid fuel was in the range of 173.98 to 525.79 kJ/mol with a conversion rate of 0.1 to 0.9. In particular, the activation energy increased largely at the higher conversion than 0.6. The kinetic analysis using a curve-fitting method suggested that livestock mature solid fuel was decomposed via a multi-step reaction which can be divided into five decomposition steps.