• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.6
• /
• pp.651-659
• /
• 2010

In this paper, a new six-port direct conversion receiver for high-speed multi-band multi-mode wireless communication system such as software defined radio(SDR) is proposed. The designed receiver is composed of two CMOS four-port BPSK receivers and a dual-band one-stage polyphase filter for quadrature LO signal generation. The four-port BPSK receiver, implemented in 0.18 ${\mu}m$ CMOS technology for the first time in microwave-band, is composed of two active combiners, an active balun, two power detector, and an analog decoder. The proposed polyphase filter adopt type-I architecture, one-stage for reduction of the local oscillator power loss, and LC resonance structure instead of using capacitor for dual-band operation. In order to extent the operation RF bandwidth of the proposed six-port receiver, we include I/Q phase and amplitude calibration scheme in the six-port junction and the power detector. The calibration range of the phase and amplitude mismatch in the proposed calibration scheme is 8 degree and 14 dB, respectively. The validity of the designed six-port receiver is successfully demonstrated by modulating M-QAM, and M-PSK signal with 40 Msps in the two-band of 900 MHz and 2.4 GHz.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.20 no.2
• /
• pp.137-143
• /
• 2015

This paper presents the intra capacitance modeling based on the winding method and section bobbin for CM choke capable of EMI attenuation of broad bands from lower to higher frequency bands and high frequency type common-mode choke capable of EMI attenuation of high frequency band used in the EMI Block of LED-TV SMPS. The case of high frequency type CM choke can be explained by the parasitic capacitance of three types of CM choke. The winding method of section bobbin type is smaller than the others. The first resonant frequency of the proposed CM choke tends to increase as the parasitic capacitance becomes small and its impedance characteristics improved performance as the first resonant frequency increases. The CM chokes of the proposed section bobbin type shows that in the future, the method may have practical use in LED/LCD-TV SMPS and in several applications, such as LED lighting, adapters, and so on.

• Smart Structures and Systems
• /
• v.2 no.2
• /
• pp.141-154
• /
• 2006

Recently, the Hilbert-Huang transform (HHT) has gained considerable attention as a novel technique of signal processing, which shows promise for the system identification and damage detection of structures. This study investigates the effectiveness and accuracy of the HHT method for the system identification and damage detection of structures through a series of experiments. A multi-degree-of-freedom (MDOF) structural model has been constructed with modular members, and the columns of the model can be replaced or removed to simulate damages at different locations with different severities. The measured response data of the structure due to an impulse loading is first decomposed into modal responses using the empirical mode decomposition (EMD) approach with a band-pass filter technique. Then, the Hilbert transform is subsequently applied to each modal response to obtain the instantaneous amplitude and phase angle time histories. A linear least-square fit procedure is used to identify the natural frequencies and damping ratios from the instantaneous amplitude and phase angle for each modal response. When the responses at all degrees of freedom are measured, the mode shape and the physical mass, damping and stiffness matrices of the structure can be determined. Based on a comparison of the stiffness of each story unit prior to and after the damage, the damage locations and severities can be identified. Experimental results demonstrate that the HHT method yields quite accurate results for engineering applications, providing a promising tool for structural health monitoring.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.6
• /
• pp.1170-1174
• /
• 2009

Two frequency-reconfigurable antennas have been designed and combined in a space with limited volume, i.e., 40mm ${\times}$ 20mm ${\times}$ 6mm. Each antenna can be reconfigured to operate at different frequency bands depending on the state of an embedded switch, which is implemented using a PIN diode. The first antenna can be switched between 0.82GHz ${\sim}$ 0.96GHz band (GSM/ CDMA) and 1.7GHz ${\sim}$ 2.17GHz band (DCS/ PCS/ WCDMA), which are cellular bands. The second antenna can be switched between 3.4GHz ${\sim}$ 3.6GHz band (mWiMax) and 2.3GHz ${\sim}$ 2.5GHz, 5.15GHz ${\sim}$ 5.35GHz bands (WiBro/ WLAN 11a/b/g/n), which are connectivity bands. The proposed combined antenna operates both over cellular bands and connectivity bands concurrently. The choice of the operation bands is made independently by the states of the two switches.

• The Journal of the Acoustical Society of Korea
• /
• v.20 no.5
• /
• pp.35-47
• /
• 2001

This paper describes an efficient harmonic-CELP speech coder by taking advantages of harmonic and CELP coders into account. According to frame voicing decision, the proposed harmonic-CELP coder adopts the RP-VSELP coder as a fast CELP in case of an unvoiced frame, or an improved harmonic coder in case of a voiced frame. The proposed coder has main features as follows: simple pitch detection, fast harmonic estimation, variable dimension harmonic vector quantization, perceptual weighting reflecting frequency resolution, fast harmonic synthesis, naturalness control using band voicing, and multi-mode. These features make the proposed coder require very low complexity, compared with HVXC coder To demonstrate the performance of the proposed coder, a 2.4 kbps coder has been implemented and compared with reference coders. From results of informal listening tests, the proposed coder showed good quality while requiring low delay and complexity.

• ETRI Journal
• /
• v.26 no.3
• /
• pp.229-240
• /
• 2004

This paper reports on our development of a dual-mode transceiver for a CMOS high-rate Bluetooth system-onchip solution. The transceiver includes most of the radio building blocks such as an active complex filter, a Gaussian frequency shift keying (GFSK) demodulator, a variable gain amplifier (VGA), a dc offset cancellation circuit, a quadrature local oscillator (LO) generator, and an RF front-end. It is designed for both the normal-rate Bluetooth with an instantaneous bit rate of 1 Mb/s and the high-rate Bluetooth of up to 12 Mb/s. The receiver employs a dualconversion combined with a baseband dual-path architecture for resolving many problems such as flicker noise, dc offset, and power consumption of the dual-mode system. The transceiver requires none of the external image-rejection and intermediate frequency (IF) channel filters by using an LO of 1.6 GHz and the fifth order onchip filters. The chip is fabricated on a $6.5-mm^{2}$ die using a standard $0.25-{\mu}m$ CMOS technology. Experimental results show an in-band image-rejection ratio of 40 dB, an IIP3 of -5 dBm, and a sensitivity of -77 dBm for the Bluetooth mode when the losses from the external components are compensated. It consumes 42 mA in receive ${\pi}/4-diffrential$ quadrature phase-shift keying $({\pi}/4-DQPSK)$ mode of 8 Mb/s, 35 mA in receive GFSK mode of 1 Mb/s, and 32 mA in transmit mode from a 2.5-V supply. These results indicate that the architecture and circuits are adaptable to the implementation of a low-cost, multi-mode, high-speed wireless personal area network.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.9
• /
• pp.1000-1009
• /
• 2008

The purpose of this paper is to analyze the performance of MB-OFDM UWB system when the interference signal that can be WIMAX signal or 4 G system signal is received by detection limit of -80 dBm/MHz proposed in Korea for DAA(Detect And Avoid) to permit UWB in $3.1{\sim}4.8$ GHz. MB-OFDM UWB system supports two transmission modes; one is TFI(Time frequency Interleaving) mode that transmits OFDM symbols using different carrier frequency from symbol to symbol according to Time Frequency(TF) codes, the other is FFI(Fixed Frequency Interleaving) mode that transmits OFDM symbols using a specific carrier frequency. In this paper, we considered the TX average power and the synchronization structure to reflect the effect of frequency hopping according to TFC. Interference analysis results show that the WiMAX system is fenced thoroughly from UWB interference in domestic DAA regulation, but the performance of MB-OFDM UWB system is degraded seriously by an interference signal with the DAA detection limit even in frequency Hopping mode that can get frequency diversity effect.

• The Bulletin of The Korean Astronomical Society
• /
• v.38 no.2
• /
• pp.74.2-74.2
• /
• 2013

Recent spectroscopic observations have provided evidences for the multiple stellar populations having different abundances in some massive globular clusters (GCs). In particular, some of these GCs show clear separations of red giant-branches (RGBs) in calcium narrow band photometry. In order to confirm the differences in heavy element abundances and radial velocities among multiple RGBs, we have performed the low-resolution spectroscopy for the RGB stars in these GCs. The spectral data were taken from the multi-object spectroscopic mode with WFCCD mounted on the du Pont 2.5m telescope in Las Campanas Observatory. In this talk, we will present our progress in the spectroscopic analysis of the RGB stars in these GCs.

• Proceedings of the Optical Society of Korea Conference
• /
• 2000.02a
• /
• pp.238-239
• /
• 2000

The optical fibers are an interesting medium for effective tunable optical frequency conversion in the spectral range of UV, Visible, and near-IR through the nonlinear processes. A number of papers for developing the wideband and flat-gain amplifier for the WDM system applications through the combination of EDFA or thulium-doped fluoride fiber amplifier and Raman amplifier, are reported$^{(1)}$ . Even though a variety of papers related to Raman amplifications are published, the amplification with the feedback of the residual pump is not investigated yet. Accordingly, in this paper, we report the characteristics of forward Raman amplification by the simple and double-pass fiber Raman configuration through the feedback of residual pump beam. (omitted)

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.1120-1125
• /
• 2001

A new concept of piezoelectric smart panels for noise reduction in wide band frequencies is proposed and their possibility is experimentally investigated. Multi-mode damping is studied by using a newly proposed tuning method. The proposed panels are based on passive shunt damping methods. This method is based on electrical impedance model and maximizing the dissipated energy at the shunt circuit. four PZT are attached on smart panel for improving performance of transmission noise reduction. 0 prove the concept of piezoelectric smart panels, an acoustic measurement experiment was performed. The smart panels exhibit a good noise reduction in middle and high frequency ranges due to the mass effects of absorbing materials or/and the air gap. The use of piezoelectric smart panel renders noise reduction at resonance frequency. Noise reduction at multiple resonance frequencies is experimentally investigaed.