• Journal of the Korean Ceramic Society
• /
• v.49 no.3
• /
• pp.216-220
• /
• 2012

Mullite formation in a porcelain body was promoted extensively by replacing kaolinite with pyrophyllite. Effects of mullite formation and vitrification by substitution of kaolinite with pyrophyllite on the mechanical and thermal properties were investigated. Addition of 45-55% pyrophyllite (pyrophyllite (45-55%)-feldspar (30%)-Gairome clay (20%)) could vitrify the sintered samples (water absorption : 0.05%, bulk density : 2.66g/cc) and improve the flexural strength (122MPa) when fired at $1280^{\circ}C$. Mullite formation was found to be decreased with increasing content of pyrophyllite. On the contrary, beyond 50% of pyrophyllite quartz and cristobalite phases was found to be increased. Thermal expansion coefficient of the samples decreased with increase of mullite phase. In triaxial system of pyrophyllite-feldspar-clay, the mullite formation of the samples with 50% pyrophyllite reaches about 78.7% and thermal expansion coefficient was found to be $5.4{\times}10^{-6}/K$.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.18 no.3
• /
• pp.337-346
• /
• 2020

Two commonly used ceramics in molten salt research are alumina and mullite. The two ceramics were exposed to a combination of rare earth chlorides (YCl₃, SmCl₃, NdCl₃, PrCl₃, and CeCl₃; each rare earth chloride of 1.8 weight percent) in LiCl-KCl at 773 K for approximately 13 days. Scanning electron microscopy with wave dispersion spectra was utilized to investigate a formation layer or deposition of rare earths onto the ceramic. Only the major constituents of the ceramics (Al, Si, and O₂) were observed during the wave dispersion spectra. X-ray fluorescence was used as well to determine concentration changes in the molten salt as a function of ceramic exposure time. This study shows no evidence of ionic exchange or layer formation between the ceramics and molten chloride salt mixture. There are signs of surface tension effects of molten salt moving out of the tantalum crucible into secondary containment.

• Korean Journal of Materials Research
• /
• v.5 no.7
• /
• pp.888-896
• /
• 1995

In this paper the manufacture of shrinkage-free in situ Mullite-ZrO$_2$ceramics through the addition of Al base metal powder to the mixture of ZrSiO$_4$and A1$_2$O$_3$was attempt. The ZrO$_2$-strengthened mullite ceramics was prepared after the following reaction form, 3(Al+Al$_2$O$_3$)+2ZrSiO$_4$longrightarrow3A1$_2$O$_3$.2SiO$_2$+2ZrO$_2$Al metal powder was added from none to 30 weight percent to the A1$_2$O$_3$. The powders were mechanically mixed, isostatically pressed and reaction sintered at 1450-1$600^{\circ}C$ for 3hours. The specimens were sintered with and without intrim soaking time for 5 hours at 125$0^{\circ}C$ for the oxidation of Al-powder The addition of aluminium accelerates the reaction and compensate the shrinkage during the sintering through an increase in volume of oxidized Al. Because coarse flake type Al metal powders were not effectively milled, oxidized Al resulted in the relative large pore in the specimen.

• Korean Journal of Materials Research
• /
• v.20 no.2
• /
• pp.72-77
• /
• 2010

Glass-ceramics were fabricated by heat-treatment of glass obtained by melting a coal bottom ash with $Li_2O$ addition. The main crystal grown in the glass-ceramics, containing 10 wt% $Li_2O$, was $\beta$-spodumene solid solution, while in $Li_2O$ 20 wt% specimen was mullite, identified using XRD. The activation energy and Avrami constant for crystallization were calculated and showed that bulk crystallization behavior will be predominant, and this expectation agreed with the microstructural observations. The crystal phase grown in $Li_2O$ 10 wt% glass-ceramics had a dendrite-like shaped whereas the shape was flake-like in the 20 wt% case. The thermal expansion coefficient of the $Li_2O$ 10 wt% glass-ceramics was lower than that of the glass having the same composition, owing to the formation of a $\beta$-spodumene phase. For example, the thermal expansion coefficient of $Li_2O$ 10 wt% glass-ceramics was $20\times10^{-7}$, which is enough for application in various heat-resistance fields. But above 20 wt% $Li_2O$, the thermal coefficient expansion of glass-ceramics, on the contrary, was higher than that of the same composition glass, due to formation of mullite.

• Journal of the Korean Ceramic Society
• /
• v.32 no.5
• /
• pp.626-634
• /
• 1995

The SiC-porcelain powder mixtures containing 51.9wt% SiC are produced as by-products from the surface abrasion process of porcelain cores. This raw powders were used as starting materials for the synthesis of SiC containing ceramics. The specimen, which was fired at 135$0^{\circ}C$ from raw powders, had SiC, $Al_{2}O_{3}$, , cristobalite, mullite as crystalline phases, and the fractured microstructure showed dispersed SiC crystalline particles almost wetted with glassy matrix and spherical pores. Although the oxidation of SiC containing powder compacts wetted with glassy matrix and spherical pores. Although the oxidation of SiC containing powder compacts started at the range of 600~80$0^{\circ}C$ form the analysis of weight gain, the presence of $SiO_{2}$ crystallien phase and cristobalite was confirmed at 100$0^{\circ}C$ by XRD analysis. Mullitization of specimens was accelerated by preheating before the final firing. The specimen sintered at 135$0^{\circ}C$ after 100$0^{\circ}C$ preheating consisted of SiC, cristobalite, mullite as crystalline phases, and revealed 2.24g/$cm^{3}$ bulk density, 11.73% water adsorption, porous microstructure with small amount of glassy phase. SiC contents of specimens, which was 51.9 wt% in the raw powders, reduced to 37~22 wt% after firing at 135$0^{\circ}C$ depending on the preheating condition.

• Korean Journal of Materials Research
• /
• v.31 no.6
• /
• pp.313-319
• /
• 2021

Understanding of effects of changes in the particle size of the matrix material on the mullite whisker growth during the production of porous mullite is crucial for better design of new porous ceramics materials in different applications. Commercially, raw materials such as Al₂O₃/SiO₂ and Al(OH)₃/SiO₂ are used as starting materials, while AlF₃ is added to fabricate porous mullite through reaction sintering process. When Al₂O₃ is used as a starting material, a porous microstructure can be identified, but a more developed needle shaped microstructure is identified in the specimen using Al(OH)₃, which has excellent reactivity. The specimen using Al₂O₃/SiO₂ composite powder does not undergo mulliteization even at 1,400 ℃, but the specimen using the Al(OH)₃/SiO₂ composite powder had already formed complete mullite whiskers from the particle size specimen milled for 3 h at 1,100 ℃. As a result, the change in sintering temperature does not significantly affect formation of microstructures. As the particle size of the matrix materials, Al₂O₃ and Al(OH)₃, decreases, the porosity tends to decrease. In the case of the Al(OH)₃/SiO₂ composite powder, the highest porosity obtained is 75 % when the particle size passes through a milling time of 3 h. The smaller the particle size of Al(OH)₃ is and the more the long/short ratio of the mullite whisker phase decreases, the higher the density becomes.

• Korean Journal of Materials Research
• /
• v.32 no.5
• /
• pp.258-263
• /
• 2022

Porous ceramics have the advantages of low density, low thermal conductivity, and excellent mechanical properties. Among porous ceramic manufacturing methods, the replica template method allows the easy manufacturing of porous filters with the highest porosity and pores of the desired size, but it also has the disadvantage that the resulting filters have low mechanical strength. To overcome this shortcoming, mullite (3Al₂O₃·2SiO₂) whiskers, which have excellent thermal stability and high mechanical strength, were introduced in porous ceramic structure. The mullite whiskers were synthesized using a composition of Al₂O₃, flyash and MoO₃. The morphologies and crystal structures of the mullite whiskers with MoO₃ contents were investigated in detail. When the porous ceramic with mullite whiskers was fabricated using 20 wt% MoO₃ catalyst the most uniform microstructure was obtained, and the mullite whiskers showed the highest aspect ratio of 47.03. The porosity and compressive strength of the fabricated porous ceramic were 82.12 % and 0.83 MPa, respectively.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.101-102
• /
• 2006

Processing techniques for producing microcellular silicon carbide, mullite, and cordierite ceramics have been developed by a reaction method that incorporates a polysiloxane and reactive fillers. The techniques developed in this study offer substantial flexibility for producing microcellular ceramics whereby cell size, cell density, degree of interconnectivity, composition, and porosity can all be effectively controlled. It is demonstrated that the adjustment of filler composition enables the possibility of tailoring the composition and properties of the microcellular ceramics. The present results suggest that the proposed novel processing techniques are suitable for the manufacture of microcellular ceramics with high morphological uniformity.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2004.10a
• /
• pp.89.3-89.3
• /
• 2004

• Korean Journal of Materials Research
• /
• v.3 no.6
• /
• pp.624-631
• /
• 1993

The composites in the system aluminium titanate-mullite were synthesized by stepwise alkoxide hydrolysis of tetraethylorthosilicate, Si(OCLH5), and titaniumtetraethoxide, $Ti(OC_{2}H_{5})_4$ in $Al_{2}O_{3}$ ethanolic colloidal solution. All particles produced by sol-gel-process were amorphous, monodispesed and had a narrow particle size distribution. Sintered bodies at $1600 ^{\circ}C$ for 2h were subjected to prolonged durability tests-on the one hand annealing at the critical decomposition temperature of $1100 ^{\circ}C$ for lOOh and on the other cyclic thermal shock between 750 and $1400 ^{\circ}C$ for 100h. The best thermal durability was achieved by a composition containing 70 and 80 vol% aluminium titanate, which showed little change in microstructure and thermal expansion cycles during the tests. The microstructural degradation of samples studied using scanning electron microscopy, X-ray diffraction, and dilatometry, was presented here. The study was conducted in order to predict the service life of aluminium titanate-mullite ceramics formed by this processing route.