• 드라이브 ㆍ 컨트롤
• /
• 제9권4호
• /
• pp.1-7
• /
• 2012

The voice coil linear force motor is a kind of a direct drive motion device that uses a permanent magnetic field and coil winding to produce force. In order to design a voice coil linear force motor, an exact calculations of the required force, the flux density in air gap and the flux pathway are needed. A conventional method can be used usually to calculate the flux density in air gap, but with this method it is needed to find a magnetic circuit revision constant. In this paper a voice coil linear force motor is designed by conventional design method and analyzed by 3D simulation program "Flux". For the prototype linear force motor, the results of the calculated by conventional design method and the analyzed by 3D simulation program are compared with the test result. Finally it is showed that the magnetic circuit revision constant which is found by comparing of the analyzed and the measured data can be used for the design of the voice coil type linear force motor to minimize the trial and error.

• 수산해양기술연구
• /
• 제30권1호
• /
• pp.25-32
• /
• 1994

An underwater speaker was made of a moving coil driver unite of usual speaker, acryl-boards, polyester resin, rubber and castor oil and it's frequency characteristics was measured in range of 250~600Hz in air water tank and sea. The results of measurements are follows: 1. Transmitting and receiving frequency of measurement frequency were similar in air, water tank and sea. 2. The input and output wave forms of a manufactured speaker which is not water-proof in air were similar to each other in 300~450Hz, but other frequencies showed distorted wave forms. 3. The input and output wave forms of an underwater speaker in water thank and sea were similar to each other in 250~600Hz. But output wave forms showed combination waves with very low frequency. 4. Transmitting and receiving frequency wave forms and resisting pressure of an underwater speaker at 80m in the depth of water were in good condition. Therefore it can be possible to use it as an underwater speaker.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 A
• /
• pp.224-227
• /
• 1998

Linear motors are increasingly employed as direct actuators replacing the more conventional systems composed by a rotating motor and a mechanical device. Linear DC motor is useful in a high speed and high accuracy positioning system with a feedback controller. Because of these advantages, linear DC motors have already been used as motors of pen recorders and magnetic disk storage devices, these are moving coil type linear DC motors as these movers are light. Moving magnet type linear DC motor has advantages at long stroke motors because its mover's feeding wires for driving is not necessary. This paper is concerned with the analysis of linear DC motor that is moving magnet type with unipolar. In order to analyze the dynamic behaviour a mathematical model based on a simplified field analysis developed. A two dimensional finite element field solution is employed in order to illustrate the effect of yoke saturation and motor performance. It is deduced the relation between the limit value of the thrust of the linear DC motor and the dimension of the yokes.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계학술대회논문집
• /
• pp.750-755
• /
• 2005

This paper proposes a small VCM (Voice coil motor) type actuator using curved suspensions for auto-focusing and zoom motions for mobile information devices. 1'he proposed focusing actuator adopts a nontraditional type of suspension using curved beams in order to extend output displacement within small height restriction. The curved beam is similar to the leaf spring type which is usually used in optical disk drives. In addition, three different materials are considered for the curved suspension model, and Aluminum shows the best dynamic characteristics. The proposed zoom actuator does not use a suspension supporting bobbin but a moving rail and a sloper mechanism by generating rotational force at lens holder. The sensitivity of design parameters on output performance is studied using ANSYS (3D FEM tool). Experiments using a prototype of the proposed actuator model verified the analytical prediction and performance.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 B
• /
• pp.1091-1093
• /
• 2004

This paper deals with two structures of tubular LOA. One is the moving-coil type LOA and the other is moving-magnet type LOA. We analyze and compare the characteristics of tubular LOA according to mover type. The results of predicitions from the analysis are compared with corresponding finite element analysis.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 A
• /
• pp.196-199
• /
• 1998

LDM(Linear DC Motor) are used in high speed, high-precision position control system. Because of these advatages, LDM has already used in the motor of pen-recorder, magnetic-disk devices. Under the limited dimension, we propose the design method of LDM by magnetic circuit. In this paper, a relation between the thrust constant and size of a LDM that is moving coil type with unipolar is described, which is defined as a simple relational equation. To maximize the rate of thrust to the volume of LDM, the magnetic flux density in the yoke is adjusted to the value of magnetic equation. By the magnetic field analysis(FEM), the validity of the equation is confirmed.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제49권11호
• /
• pp.713-719
• /
• 2000

This paper presents an approach toward improving the performance of Moving Coil Type Linear Oscillatory Actuator (MC-LOA) with the application of Finite Element Method (FEM) to a simple control system. MC-LOA has an unbalanced magnetic circuit due to its asymmetric structure and there is a different flux distribution on the air-gap along the current direction. The interaction driven by two fluxes between the Permanent Magnet (PM) and the current causes the unbalanced thrust and interferes with the proper oscillation of MC-LOA. In order to solve the above problems and improve the driving performance, it is necessary to analyze the rate of the unbalanced thrust according to the current direction by using FEM. Then, the analysis results are used to determine the input currents for both directions. Controlling the input currents can be easily achieved by a simple control system, such as Pulse Width Modulation (PWM), without complex units. The validity of the approach is verified by the experimental results.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문초록집
• /
• pp.378.2-378
• /
• 2002

This paper deals with a moving coil type linear motor for fast access of the miniature ODD. This slim-line motor is composed of the mover supported by guide mechanism, the coil wound into it, and the yoke attached to the permanent magnet for stator. The driving force is generated by the PM of the stator and the current in the coil of the mover. Magnetic circuit analysis and Finite Element Method are applied to estimate force at air gap. (omitted)

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 추계학술대회논문집
• /
• pp.226-233
• /
• 2003

There are many researches going on to develop the information storage devices using Blue-ray disc and DVD as a demand for high-density information storage devices is highly increasing. This high-density information storage device requires a short-wave laser and objective lens of high numerical aperture set in fer its operation. And, that brings out rapid decrease of tilt tolerance. Therefore, it is necessary that an actuator should control tilt motions to get a stable signal. In this paper, a new mathematical form of 3-D.O.F coupled model is formulated and magnetic circuit in constraints is most effectively designed with the use of the moving coil type actuator in higher sensitivity. Further, this paper presents a tilt coil whose rotational center point is put on that of the lens through the variation of tilt coil and proposes a 3-axis actuator with high sensitivity improved in its dynamic property through its structure analysis.

• 한국소음진동공학회논문집
• /
• 제15권3호
• /
• pp.334-340
• /
• 2005

A disk-type 3-DOF actuator which has new principle and very simple structure is proposed. Also it utilizes the relation of bias and control fluxes produced by permanent magnets and coils, respectively, like other conventional electromagnetic actuators, but its main feature is that both the coils and permanent magnets are fixed in the stator, which makes it easy to design the shape of moving part. Operating principle is that a moving disk is driven by reaction force of Lorentz force acting on the fixed equivalent coil. Simple analytic approach and FEM analysis are performed to determine the design parameters so as to increase the driving force and distance. And some experimental results show the feasibility of the proposed actuator.