• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.895-897
• /
• 2001

It must be able to calculate thrust to design and manufacture linear BLDC motor by required specification. If magnetic energy with respect to displacement of mover of linear BLDC electric motor be obtained, thrust can be calculated. It can decide optimal design factor of linear BLDC motor through change of thrust by design variable using magnetic energy method. It can predict variation of thrust by pitch of pole and design optimally using coenergy that is attained from FEM.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.90-95
• /
• 2008

Medium and high speed marine diesel engines have been widely used as prime mover in small car ferries and fishing vessels with reduction gear. These propulsion shafting system should be installed and matched the elastic coupling between engine and reduction gear to isolate the vibratory torque. In this paper, the elastic dynamic characteristics of coupling with rubber type circular segments is confirmed by the theoretical analysis using the FEM and the hydraulic exciting test at shop. And its adaptation is investigated in the torsional vibration test in factory shop.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.55 no.9
• /
• pp.459-464
• /
• 2006

The detent force by end-effect has an undesired influence on moving coil type Permanent Magnet Linear Synchronous Motor(PMLSM). So, the reduction of detent force by end-effect is especially required for the improvement of thrust characteristics. In this paper, in order to reduce detent force by end-effect, the auxiliary-teeth is installed at the end part of mover. It is also analyzed by Finite Element Analysis(FEA) and optimized by using neural network. By comparison, the detent force is reduced about 41.4[%] comparing to that of basic model.

• Journal of Mechanical Science and Technology
• /
• v.15 no.7
• /
• pp.921-930
• /
• 2001

A new theoretical critical heat flux (CHF) model was developed for the forced convective flow boiling at high pressure, high mass velocity, and low quality. The present model for an intermittent vapor blanket was basically derived from the sublayer dryout theory without including any empirical constant. The vapor blanket velocity was estimated by an axial force balance, and the thickness of vapor blanket was determined by a radial force balance for the Marangoni force and lift force. Based on the comparison of the predicted CHF with the experimental data taken from previous studies, the present CHF model showed satisfactory results with reasonable accuracy.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2006.06a
• /
• pp.71-72
• /
• 2006

This paper introduces the results of the development of a new mobile Digital DC-arc Welding Machine (DDWM). A simple PI controller is applied to the DDWM to control the output welding current tracking the constant setting current. Furthermore, a hot-start function, an anti-stuck function, a standby mode and an intelligential circuit breaker (ICB) are included in the DDWM. The DDWM increases welding quality and saves more power energy than a conventional welding machine. Because the DDWM is changed from ready mode into the standby mode automatically after 2 minutes interval from this unload start. Then the DDWM is changed into ready mode automatically since it is reused to weld. Mover, the DDWM increases welding qualify, productivity and reduces costs of welding. So, the DDWM can have a great of contribution to the mobile welding industries. The effectiveness of the DDWM was proven by the experimental results and durable test.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.4
• /
• pp.346-351
• /
• 2011

Medium and high speed marine diesel engines with reduction gear have been widely used as prime mover in small car ferries and fishing vessels. The elastic coupling should be installed and complemented the propulsion shafting system to isolate the vibratory torque between engine and reduction gear. In this paper, the dynamic characteristics of elastic coupling with rubber type circular segments is confirmed by theoretical analysis using the FEM and the hydraulic excitation test at shop. Further adaptation was investigated with the torsional vibration test at diesel engine factory shop.

• Proceedings of the KIEE Conference
• /
• 1997.11a
• /
• pp.6-9
• /
• 1997

The study is analyzed the thrust fon:e of moving type Linear DC Motor(MM-LDM). The MM-LDM consists of a stator (platen) and mover (forcer). One of the method for calculating tile thrust of an MM-LDM is to analyze the energy gradient which is determined by the distribution of magnet flux. However, this method is very difficult when used to calculate the thrust force of this kind of LDM. The stored energy in the MM-LDM can be obtained by measuring the self-inductance and mutual-inductance of equivalent circuit of the MM-LOM and this energy gradient gives the thrust. The calculation of thrust force included in this motor shows that the mutual inductance has large influence on the generation of thrust force.

• Transactions on Electrical and Electronic Materials
• /
• v.18 no.5
• /
• pp.265-272
• /
• 2017

This paper presents the dynamic modeling, analysis, and control of an AC/DC/AC-assisted, self-excited induction generator connected to the grid. The dynamic model includes wind turbine models with pitch control, gear boxes, self-excited induction generators, excitation capacitance, inductive load models, controlled six-pulse rectifiers, and novel state-space models of a grid-connected inverter. The system has been simulated to verify its capabilities of buildup voltage, stator flux response, stator phase current, electromagnetic torque, and magnetizing inductance variation during both the dynamic and steady states with a variable-speed prime mover. The complete setup of the above dynamic models was simulated using MATLAB/SIMULINK.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.7
• /
• pp.1047-1055
• /
• 2015

We proposes a method for improving the identification and tracking of the moving objects in intelligent video surveillance system. The proposed method consists of 3 parts: object detection, object recognition, and object tracking. First of all, we use a GMM(Gaussian Mixture Model) to eliminate the background, and extract the moving object. Next, we propose a labeling technique forrecognition of the moving object. and the method for identifying the recognized object by using the optical flow and EMD algorithm. Lastly, we proposes method to track the location of the identified moving object regions by using location information of moving objects and Kalman filter. Finally, we demonstrate the feasibility and applicability of the proposed algorithms through some experiments.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.796-797
• /
• 2008

This paper presents a coupling scheme of LSM(Level Set Method) and Poisson's equation to analyze the dynamic performance of electromagnetic system with moving parts. Remeshing process is necessary to analyze the dynamics of moving object using finite element method. LSM is useful for analysis of moving objects or propagating models in time varying system. In this paper, we proposed the material setting technique of mover using level set function. To validate the algorithm, we adopted the simple hinged electromagnet model with moving arm. The results of simulation are reasonable as expect.