• 한국정보처리학회:학술대회논문집
• /
• 한국정보처리학회 2013년도 춘계학술발표대회
• /
• pp.501-503
• /
• 2013

This project presents a concept of mobile robots using prototypes, computing proposal oriented to embedded systems implementation. We implement our system using GPS module, Ultrasonic sensor(range sensors), H-bridge dual stepper control, DTMF(Dual-tone Multi-Frequency ) and LCD module. In this paper we construct a mechanical simple mobile robot model, which can measure the distance from obstacle with the aid of sensor and should able to control the speed of motor accordingly. Modules were interfaced with FPGA(Field Programmable Gate Array) controller for hardware implementation.

• 대한조선학회논문집
• /
• 제55권5호
• /
• pp.401-414
• /
• 2018

Planing hull type ships are often equipped with interceptor or trim tab to improve the excessive trim angle which leads to poor resistance and sea keeping performances. The purpose of this study is to design a controller to control the attitude of the ship by controllable stern interceptor and validate the effectiveness of the attitude control by the towing tank test. Embedded controller, servo motor and controllable stern interceptor system were equipped with planing hull type model ship. Prior to designing the control algorithm, a model test was performed to identify the system dynamic model of the planing hull type ship including the stern interceptor. The matrix components of model were optimized by Genetic Algorithm. Using the identified model, PID controller which is a classical controller and sliding mode controller which is a nonlinear robust controller were designed. Gain tuning of the controllers and running simulation was conducted before the towing tank test. Inserting the designed control algorithm into the embedded controller of the model ship, the effectiveness of the active control of the stern interceptor was validated by towing tank test. In still water test with small disturbance, the sliding mode controller showed better performance of canceling the disturbance and the steady-state control performance than the PID controller.

• 한국정밀공학회지
• /
• 제17권12호
• /
• pp.61-67
• /
• 2000

In switched reluctance motor(SRM) drive, it is necessary to synchronize the stator phase excitation with the rotor position. Therefore the rotor position information is an essential. Usually optical encoders or resolvers are used to provide the rotor position information. These sensors are expensive and are not suitable for high speed operation. In general, the accuracy of the switching angle is dependent upon the resolution of the encoder and the sampling period of the microprocessor. But the region of high speed, switching angles are fluctuated back and forth from the preset values, which are cause by the sampling period of the microprocessor. Therefore, the low cost linear encoder suitable for the practical and stable SRM drive is proposed and the control algorithm to provide the switching signals using the simple digital logic circuit is also presented in this paper. It is verified from the experiments that the proposed encoder and logic controller can be a powerful candidate for the practical low cost SRM drive.

• Journal of Power Electronics
• /
• 제1권1호
• /
• pp.56-64
• /
• 2001

This paper presents the switching angle and voltage for maximizing the torque or efficiency and minimizing torque ripple of an 8/6, SRM. The approximate analysis and computer simulation determine the switching angle and voltage by using SIMULINK$^\textregistered$. This is performed as a function of the speed and torque required by the load. From the results, new three facts can be known: First, the maximum torque depends on voltage and speed depends on switching angle. The others, the maximum efficiency and minimum torque ripple relay on switching angle. We control the switching angle and voltage of and asymmetrical inverter for the SRM with one-chip micro controller.

• Journal of Biosystems Engineering
• /
• 제30권6호통권113호
• /
• pp.327-332
• /
• 2005

In this study, the electronic power steering control system was developed and it was carried out to investigate experimentally the effect of the steering force for the on-road and off-road. The electronic power steering control system was engineered new trend system of power steering control system for tractor. It was composed of the electronic controller, detector, motor and mechanism mounted on tractor chassis. It was tested at the field in condition of tractor traveling speed 0 km/h, 3 km/h, 8 km/h, 11 km/h, 15 km/h, 18 km/h, 22 km/h, 25 km/h for measuring a maximum steering force. As a speed of tractor increased, a steering force decreased regardless of on-road or off-road. In addition, it is sufficiently a possibility of application of the steering system of tractor.

• 한국산학기술학회논문지
• /
• 제13권8호
• /
• pp.3647-3653
• /
• 2012

능동 소음제어 시스템에 사용되는 IIR 필터 구조는 구조적으로 안정성이 보장되어야 하며 이는 분모 전달 함수의 근이 단위원 내부에 존재하여야 한다. 따라서 이를 결정하는 제어 필터의 계수의 적절한 조정이 중요해 진다. 본 논문에서는 적응과정에서 불안정할 우려가 있는 IIR 필터 구조를 가지는 Filtered_U LMS 알고리즘에 안정화 알고리즘과 수렴속도 향상을 위한 퍼지논리를 이용한 수렴계수 계산 알고리즘을 제안하였다. 제안한 알고리즘이 FIR 필터 구조 알고리즘보다 계산량이 적고 수렴특성이 우수함을 시뮬레이션을 통하여 보였다.

• 한국분무공학회지
• /
• 제27권3호
• /
• pp.155-160
• /
• 2022

Recently, major developed countries have strengthened automobile fuel efficiency regulations and carbon dioxide emission allowance standards to curb climate change caused by global warming worldwide. Accordingly, research and manufacturing on electric vehicles that do not emit pollutants during actual driving on the road are being conducted. Several automobile companies are producing and testing electric vehicles to commercialize them, but it takes a lot of manpower and time to test and evaluate mass-produced electric vehicles with driving mileage of more than 300km on a per-charge. Therefore, in order to reduce this, a simulation model was developed in this study. This study used vehicle information and MCT speed profile of small electric vehicle as basic data. It was developed by applying Simulink, which models the system in a block diagram method using MATLAB software. Based on the vehicle dynamics, the simulation model consisted of major components of electric vehicles such as motor, battery, wheel/tire, brake, and acceleration. Through the development model, the amount of change in battery SOC and the mileage during driving were calculated. For verification, battery SOC data and vehicle speed data were compared and analyzed using CAN communication during the chassis dynamometer test. In addition, the reliability of the simulation model was confirmed through an analysis of the correlation between the result data and the data acquired through CAN communication.

• 대한방사선치료학회지
• /
• 제26권2호
• /
• pp.305-312
• /
• 2014

목 적 : 동적다엽조준기(dynamic multileaf collimator, DMLC)에서 leaf 속도 정도관리 시 획득된 dynalog 파일을 이용하여 leaf 속도 정확성을 평가하고 정도관리와 모터 교체의 연관성을 분석하여 정도관리의 유용성을 살펴보고, 이를 통해 leaf 속도 정도관리의 적절한 주기를 파악하고자 하였다. 폐암의 정위적체부방사선치료시 실제 적용하고 있는 최대강도투사(MIP) 영상과 호흡위상별(0~90%)영상에서 3차원적으로 재구성된 선량 분포 차이를 평가하고자 한다. 대상 및 방법 : 다엽조준기(multileaf collimator, MLC) 모터 120개에 대해 2012년 1월부터 2014년 6월까지 leaf 위치의 정확성과 치료 중심점(isocenter) 일치도 및 leaf 속도의 정확성에 대해 정도관리를 하였다. leaf 위치 정확성은 모눈종이를 사용하였으며, 또한 leaf의 치료 중심점 일치도를 평가하였다. 그리고 약 1~2 주에 1회씩 총 92회의 leaf 속도 정도관리를 통해 모터 교체회수를 파악하여 leaf 속도 정도관리와 모터 교체와의 상관관계를 분석하였으며, 교체된 모터로부터 leaf의 RMS 값이 점차적으로 증가하는 경우와 급격하게 증가하는 경우로 나누어 적절한 정도관리 주기를 평가하였다. 또한 정도관리를 통해 획득된 RMS 값과 전혀 무관하게 그리고 정도관리를 통해 교체된 모터 횟수를 분석하여 leaf 속도 정도관리의 유용성을 알아보았다. 결 과 : leaf 위치의 정확성과 치료 중심점 일치도를 측정한 결과는 TG-142 보고서에서 권고 하는 허용 범위 이하의 정확성으로 관찰되었고, leaf 속도 정도관리는 총 92회를 시행한 결과 MLC 모터 교체 회수는 56회 이었다. 정도관리를 통해 교체된 모터에서 leaf의 RMS 값이 점차적으로 증가한 경우가 급격하게 증가한 경우에 비해 많았으며, RMS 값이 점차적으로 증가하는 경우는 평균값이 0.298 cm 이었고 급격하게 증가한 경우는 평균값이 0.273 cm 이었다. 모두 에러 히스토그램이 1 cm 이상 벗어난 횟수가 측정되어 교체하였다. RMS 값이 점차적으로 증가하여 모터가 교체될 때까지의 소요기간은 평균 22일 정도 였다. 전체 모터 교체 중 정도관리와 무관하게 그리고 정도관리를 통해 교체한 경우가 각각 28회씩으로 나타났다. 또한 방사선치료 도중 MLC 모터 고장으로 인하여 발생되는 치료 지연 시간은 약 20분 정도였다. 결 론 : 본 연구에서는 최근 IMRT 치료가 증가함에 따라 MLC 사용 빈도 역시 증가하고 있는 시점에서 leaf 위치 정확성 및 치료 중심점 일치도 그리고 속도 정확성 평가를 2년 6개월 동안 수행하였다. leaf 속도 정도관리를 통해 분석한 결과로부터 2 주에 한 번씩 정도관리를 수행하는 것이 적절한 것으로 판단된다. 이 주기를 통해서 leaf 속도 저하를 추적 관찰하여 최종 모터의 교체시기를 예측할 수 있을 것이다. 더불어 방사선치료 중 leaf의 모터 고장으로 인한 방사선치료 지연을 방지하여 좀 더 정확한 IMRT 치료가 이루어지겠다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제38권6호
• /
• pp.716-722
• /
• 2014

DC 모터 시스템의 속도 제어기를 설계하기 위해서는 먼저 시스템의 파라미터 추정이 선행되어야 한다. 본 논문에서는 유전알고리즘을 이용하여 DC 모터 시스템의 파라미터를 추정하는 기법에 대해 다룬다. 이때 사용되는 추정 모델은 1차 및 2차 모델을 고려하며, 유전알고리즘의 3가지 평가함수를 고려하여 최적화한다. 또한, 유전알고리즘이 해공간에서 최적해를 탐색하는 능력의 우수함을 보여주기 위해 수치적 해석 방법을 통한 추정 결과도 함께 비교한다. 이때 파라미터 추정에 사용되는 데이터는 실제 실험장치의 입출력데이터를 이용하며, 신호의 잡음 제거를 위해 Butterworth 필터도 함께 설계한다. 마지막으로 제안한 기법을 통해 얻어진 모델과 실제 실험장치의 데이터와 비교하여 그 유효성과 정확성을 확인한다.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2017년도 춘계공동학술대회
• /
• pp.156-156
• /
• 2017

Most crop damages have been occurred by vermin(e.g., wild birds and herbivores) during the period between seeding and the cotyledon level. In this study, to minimize the damage by vermin and acquire the benefits such as protection against weeds and maintenance of water content in soil, immediately vinyl mulching after seeding was devised. Vinyl mulching has been generally covered with black color vinyl, that crop seeding locations cannot be detected by visible light range. Before punching vinyl, non-contact and non-destructive methods that can continuously determine the locations are necessary. In this study, a crop position detection method was studied that uses infrared thermal image sensor to determine the cotyledon position under vinyl mulch. The moving system for acquiring image arrays has been developed for continuously detecting crop locations under plastic mulching on the field. A sliding mechanical device was developed to move the sensor, which were arranged in the form of a linear array, perpendicular to the array using a micro-controller integrated with a stepping motor. The experiments were conducted while moving 4.00 cm/s speed of the IR sensor by the rotational speed of the stepping motor based on a digital pulse width modulation signal from the micro-controller. The acquired images were calibrated with the spatial image correlation. The collected data were processed using moving averaging on interpolation to determine the frame where the variance was the smallest in resolution units of 1.02 cm. For this study, the spline method was relatively faster than the other polynomial interpolation methods, because it has a lower maximum order of formulation when using a system such as the tridiagonal linear equation system which provided the capability of real-time processing. The temperature distribution corresponding to the distance between the crops was 10 cm, and the more clearly the leaf pattern of the crop was visually confirmed. The frequency difference was decreased, as the number of overlapped pixels was increased. Also the wave pattern of points where the crops were recognized were reduced.