• Journal of the Korean Wood Science and Technology
• /
• 제31권1호
• /
• pp.27-31
• /
• 2003

이 논문은 소나무와 일본잎갈나무의 변장 14.0 cm와 16.5 cm인 큰 정각재의 천연건조과정과 함수율분포에 관한 내용으로서 건조속도는 건조개시 첫 8주 동안 비교적 컸었으나, 그 이후부터 점차 감소하였다. 생재에서 규격함수율 18% 수준까지 건조시간은 소나무 14.0 cm와 16.5 cm가 각각 26주와 32주이고, 일본잎갈나무의 경우는 각각 32주와 48주이었다. 이들 정각재의 재장방향과 두께방향의 수분경사는 비교적 완만하였다. 일본잎갈나무의 수분경사는 소나무의 것보다 컸었고, 일본잎갈나무의 변장의 크기가 수분경사에 미치는 영향은 소나무의 것보다 컸었다.

• Journal of the Korean Wood Science and Technology
• /
• 제10권3호
• /
• pp.167-167
• /
• 1982

Italian poplar (Populus euramericana) rotary veneers were press-dried and air-dried to study drying curves, thickness shrinkage and width shrinkage of them under several drying conditions such as drying temperatures and veneer thicknesses. The results of the study are summarized as follows; 1. In press-drying, drying times from green condition to about final moisture content of 10 percent with veneer thickness of 0.6mm by platen temperatures required about 10 minutes at platen temperature of $100^{\circ}C$, 3 minutes at $110^{\circ}C$, 1 minute at $120^{\circ}C$ and $130^{\circ}C$, respectively. 2. In press, drying, drying times from green condition to about final moisture content of 10 percent by veneer thicknesses required 2 minutes at veneer thickness of 0.6mm, 4 minutes at 1.2mm,6 minutes at 1.8mm and 9 minutes at 3.6mm, respectively. 3. In air-drying, drying times from green condition to air-dried moisture content by veneer thicknesses required 15 hours at veneer thickness of 0.6mm, 18 hours at 1.2mm and 23 hours at 2.4mm, respectively. 4. Thickness shrinkage of press-drying was remarkably greater than that of air-drying, but width shrinkage of press-drying was rather smaller. 5. Difference of thickness shrinkage among platen temperatures was insignificant, and width shrinkage at platen temperature of $130^{\circ}C$ was the least.

• 한국화재소방학회논문지
• /
• 제18권4호
• /
• pp.16-21
• /
• 2004

본 논문은 국내에서 소방관이 사용하고 있는 공기호흡기 중 년도별로 폐기처분되는 공기호흡기를 수거 후 절단하여 실린더 재질의 상태를 기기분석을 통하여 관찰하였으며, 공기호흡기 실린더에서 안면부까지의 도관의 오염정도를 확인하고자 도관을 절개하여 오염여부를 확인하였다. 이로부터 공기호흡기용 압축공기가 실린더에 미치는 영향에 대하여 조사하였다. 연구결과 공기호흡기 실린더 내부의 금속표면 이 압축공기에 포함된 수분에 의한 부식이 발생된 것을 볼 수 있다. 부식에 의해 생성된 물질은 100㎛이하의 백색가루로 수분에 의해 부식된 수산화알루미늄이며, 부식으로 인해 발생한 이러한 수산화알루미늄 분말은 호흡 도중 사람의 폐에 들어갈 가능성이 있으며, 인체의 폐에 침착되기 쉽기 때문에 다른 대기오염물질보다 인체 건강에 더 큰 악영향을 초래할 것이다. 소방관이 착용하는 공기호흡기 호흡용 압축공기의 성분 및 조성에 대한 별도의 규정이 조속히 마련되어야 할 것이다.

• Transactions on Electrical and Electronic Materials
• /
• 제14권4호
• /
• pp.182-186
• /
• 2013

We studied the possibility that an air capacitor can be used as a humidity sensor by measuring capacitance change. In order to investigate the possibility, the change of capacitance of an air capacitor due to moisture in air was first considered theoretically, and was then experimentally verified. The capacitance was measured by an LCR impedance meter with a 100-kHz and 1-V ac. The results revealed that the changes in the experimentally measured capacitances were greater than those in the theoretically calculated values. Based on this fact, we knew that an air capacitor could be used as part of a humidity sensing device. We expect the humidity sensor with an air capacitor has characteristics of fast response time, high reliability, and high durability compared with other conventional methods.

• Journal of the Korean Wood Science and Technology
• /
• 제27권1호
• /
• pp.50-55
• /
• 1999

Since ultrasonic stress wave velocity varies with wood temperature and moisture content, ultrasonic stress wave could be a tool to predict wood moisture content if temperature effect could be eliminated. This temperature effect was investigated by measuring the velocities of ultrasonic stress waves transmitting through air, a metal bar and a dimension lumber at various temperatures. For air the velocity and amplitude of the ultrasonic stress wave increase with temperature, while for a metal bar and a dimension lumber those decrease as temperature increases. However all three materials showed velocity hystereses with a temperature cycle. The effect of temperature and moisture content on stress wave velocity of a dimension lumber was depicted in the form of a three dimensional graph. The plot of stress wave velocity vs. wood moisture content was well fitted by two regression equations: a exponential equation below 46% and a linear equation above 46%.

• Journal of Biosystems Engineering
• /
• 제21권1호
• /
• pp.60-71
• /
• 1996

The purposes of this study were to develop a simulation model and to determine minimum specific airflow rate requirements for natural air drying of rough rice in Korea. A simulation model was developed considering energy and mass balances within grain bed, drying and rewetting rates, and hysterisis effect between sorption and desorption isotherms. As the results of validation test, the moisture contents predicted by the model agreed very well with the actual data. The criteria for determining minimum specific airflow rate requirements was that the top loom layer in the bin be dried to a moisture content below 16 percent wet basis with less than 0.5% drymatter decomposition. The minimum specific airflow rate requirements in 13 locations of Korea were presented based on the worst one among the past 7 to 13-year weather data. These requirements were also presented for all the combinations of three harvest dates and four harvest moisture contents. Specific airflow rate requirements seemed to be half by each 2 percent reduction in moisture content from 24 percent. As harvest date was delayed by 10 days from October 1, these requirements were reduced by about 20 to 40 percent.

• Journal of Biosystems Engineering
• /
• 제3권2호
• /
• pp.100-113
• /
• 1978

Drying grain with conventional artificial drying methods requires great quantities of petroleum fuels. Depletion of fossil fuel increases the need of the utilization of solar energy as an alternative to petroluem fuels for drying grain , an energy intensive agricultural operation. Many techniques for the utilization of solar energy in grain drying have been developed, however, there are many problems in adopting solar energy as an energy sources for drying grain. Futhermore, very little research has been done on solar grain drying in Korea. This study was conducted to evaluate the availability of solar energy for drying of rough rice in Chuncheon, Suweon, and Jinju areas based on 50year meteorological data, and to analyze experimentally the performance of a solar air collector for dying grain, and to find the effects of solar heated air compared to unheated air on the rate of drying and energy consumption required for drying of rough rice. The results of this study was may be summarized as follows ; 1. Monthly average daily total radiation on a horizontal surface in October was 260.6 ly/day for Chuncheon, 240.3 ly/day for Suweon , and 253.4 ly/day for Jinju area, respectively. 2. the ratio of monthly average daily diffuse radiation to daily total radiation on a horizontal surface was approximately 0.41 for Chuncheon, 0.45 for Suweon, and 0.44 for Jinju area, respectively. 3. Although the statistical distribution curves of daily total radiation for the three locations were not identical , the differences among them were not large and may be neglected for many practical purposes. 4. I was estimated that the optimum tilting angle of the collector in October was approximately 46 degrees for Chuncheon and Suweon and 45 degrees for Jinju. 5. The ratio of the total radiation on a optimum tilting plane to that on a horizontal plane was estimated to be 1.36 for Chuncheon, 1.31 for Suweon, and 1.27 for Jinju , respectively. 6. The collection efficiency of the solar air collector ranged from 47. 8 to 51. 5 percent at the air flow rates of 251. 1-372.96 $m^3$/hr. High efficiency remained nearly , constant during the best sunshine hours, 10 a.m. to 2 p.m. and decreased during other hours. More energy was collected as the air flow rate incresed. 7. The average temperature rise in the drying air from the solar collector for the test period varied from $6.5^\circC$ to $21.8^\circC$ above the ambient air temperature. 8. Solar-dried rough rice averaged 13.7 percent moisture (w.b.) after 130 hours of drying with the air flow rate of 1. 64 ccm/$m^3$, and rough rice dried with natural air averaged 15.1 percent moisture (w.b.) after 325 hours of drying with the same air flow rate. 9. Energy saving of 2.4 kwh per $m^3$ percentage point of moisture removed was obtained from solar heated air drYing. The solar bin used 53.3 percent less energy per percentage point of moisture removed than the natural air bin.

• 한국도로학회논문집
• /
• 제7권1호
• /
• pp.31-38
• /
• 2005

콘크리트의 타설 직후, 상대적으로 콘크리트는 높은 증기압을 갖게 되며, 주위의 대기는 낮은 증기압을 갖게 된다. 콘크리트와 대기 간의 증기압의 평형을 유지하려는 작용 때문에 콘크리트의 표면에서 대기로 수분이 이동하는 증발이 발생한다. 표면에서 일어나는 증발로 인하여 콘크리트의 내부에서도 증기압의 차이가 발생하며, 이로 인하여 콘크리트 내부의 수분이 서서히 표면으로 이동하는 수분확산이 일어난다 이 수분확산의 속도는 콘크리트의 소성 균열, 수화도, 강도와 같은 요인으로 작용하여 콘크리트의 품질에 크게 영향을 미친다. 본 논문에서는 콘크리트 수분확산의 지배방정식과 실내에서 측정된 콘크리트의 온도와 상대습도를 이용하여 초기재령의 콘크리트의 수분확산도를 역계산하였다. 역계산된 콘크리트의 수분확산도를 이용하여 콘크리트의 수분확산도 모형을 개발하였으며, 이를 입력값으로 사용하여 유한요소법에 의해 콘크리트의 상대습도를 계산하였다. 그 결과로서 계산된 상대습도는 측정된 상대습도와 대체로 일치하였다.

• 한국초지조사료학회지
• /
• 제27권3호
• /
• pp.197-208
• /
• 2007

본 연구의 목적은 TMR 제조 시 물을 첨가하여 수분 함량을 높여줄 경우 수분 함량(15, 35, 50%)과 발효제(Lactobacillus plantarum) 첨가유무에 따라 저장방법(자연노출과 밀봉보관) 경과시간별(자연노출 : 0, 6, 12, 24, 48, 72시간, 밀봉보관 : 0, 2, 6, 10, 14, 18일) 사료가치 변화를 조사할 목적으로 실시하였으며 그 결과는 다음과 같다. 자연노출 상태로 저장한 경우, 수분 함량이 적을수록 외관상태가 양호하였으며 수분 함량이 높을수록 곰팡이가 생기는 시기가 빨라짐을 알 수 있었다. 시료의 냄새도 수분함량별, 발효제 첨가유무별로 달랐는데 물만 첨가하여 수분 함량을 35%와 50%로 맞춘 시료는 자연노출 24시간째에 시큼한 냄새가 나기 시작하였으나 같은 수분 함량의 시료에 발효제를 첨가한 시료에서는 발효에 의한 냄새로 시큼한 냄새가 나지 않았고 오히려 발효로 인해 향긋한 냄새가 났다. 발효제를 첨가하지 않은 시료에서는 자연노출 후 6시간이 경과하면서 지속적으로 내부온도가 상승하는 경향을 나타내고 있으며, 발효제를 첨가한 수분 함량 50% 시료에서는 자연노출 6시간부터 지속적으로 온도가 상승하는 경향을 나타낸 반면, 발효제를 첨가한 수분 35% 시료는 자연노출 48시간부터 온도가 급격히 상승함을 보이고 있다. 발효제를 첨가한 시료를 자연노출 시 수분 함량에 따른 경과시간별 pH 변화를 보면, 수분 15%에서는 경과시간에 따른 변화가 적었으나 수분 35%와 50% 시료는 각각 12시간째와 24시간째부터 pH가 급격하게 증가 하였다. 자연노출 시 같은 수분 함량의 TMR 시료에서 발효제를 첨가한 것은 6시간까지는 암모니아 발생이 낮아지다가 6시간 이후부터 암모니아 농도가 증가하는 경향을 나타낸 반면, 발효제를 첨가하지 않은 것은 12시간 이후에 암모니아 농도가 증가하는 경향을 나타내었다. 자연노출 시 영양소 함량 변화는 경과시간이 진행됨에 따라 수분의 증발로 인해 영양소 함량이 증가하는 경향을 나타내었으며, 밀봉보관 시에도 같은 경향을 나타내었다. 이상과 같은 결과를 종합해 보면, TMR 제조 시 수분함량을 조절하기 위하여 물을 첨가시킬 때 물만 첨가하는 것보다는 물에 발효제(Lactobacillus plantarum)를 섞어 주는 것이 경과시간에 따른 TMR의 사료가치 저하를 방지할 수가 있을 것으로 사료되었다.

• Journal of Biosystems Engineering
• /
• 제30권3호
• /
• pp.155-160
• /
• 2005

The objective of this research was to establish a domestically available cooling storage technique by cold-air in winter, using winter cool air ventilation fur determining rough rice cooling method in the storage and dry bin. The rough rice storage characteristics of two test conditions, winter cool-air ventilation storage and ambient temperature storage, were evaluated from January to July 2001, using a storage and dry bin of 300-ton capacity. Results of this research are as follows: Grain temperature was from $-5.1\~-8.5^{\circ}C$ after winter cool-air ventilation, and grain initial temperature for ambient temperature bin storage was $0.3\~1.9^{\circ}C$. Moisture content of rough rice decreased from $0.28\;to\;0.93\%$ and from $1.53\;to\;1.92\%$ to compare with original moisture contents for winter cool-air ventilation, and for ambient temperature bin storage, respectively. Broken ratio of brown rice from winter cool-air ventilation bin increased from $0.16\;to\; 0.92\%$, and brown rice broken ratio was from $2.24\;to\;2.86\%$ for ambient temperature bin storage to compare with initial broken ratio. Hardness of stored rice increased along storage period increase in alt storage methods, and cooling bin storage increased rice hardness of 0.271kgf: this increasing was lower then the other methods from 0.059 to 2.239kgf. Germination rates were decreased approximately 9.03, 3.14 and $3.20\%$ for upper, middle, and bottom of ventilating winter air bin, respectively, and germination rates of 2.70, 3.47 and $4.14\%$ were approximately decreased for upper, middle, and bottom parts of ambient temperature bin storage, respectively.