• Resources Recycling
• /
• v.8 no.1
• /
• pp.44-51
• /
• 1999

Converter slag was reduced and modified by the simultaneous addition of carbon and waste foundry sand as a $SiO_2$ source. The basic properties such as phase distribution, composition, specific density, hardness. absorption of water and compressive strength of modified slags were measured. The Iron recovery was significantly affected by the basicity of slag. The properties of slow cooled-modified slags of basicity 1.34 arc very similar to the natural aggregates.

• Journal of the Korean Ceramic Society
• /
• v.18 no.3
• /
• pp.157-162
• /
• 1981

A converter slag has been heat-treated above melting point at reduced condition by cokes. As the result, most iron was separated. To make hydraulic compounds, calcium oxide was added to the reduced converter slag and the mixtures were sintered. This modified converter slag clinker mainly contained tricalcium silicate and calcium aluminates, and have a great potential to be a good hydraulic cement. The hydrates of the hydraulic compounds and gypsum with and without granulated slags, were mainly C-S-H, ettringite, calcium monosulfoaluminate hydrate, calcium aluminate hydrate, and $Ca(OH)_2$

• Journal of the Korean Ceramic Society
• /
• v.17 no.4
• /
• pp.217-221
• /
• 1980

Hydration of granulated blastfurnace slag-gypsum-$C_4A_3\bar{S}$ clinker/modified converter slag clinker was investigated to develop the cement of slag-gypsum system. In the hydration of granulated slag-gypsum-$C_4A_3\bar{S}$ system clinker, the hydrates such as ettringite, CSH gel and $AH_3$ gel were formed, and the strength of hardened body would be increased by forming compact microstructure. The modified converter slag clinker which contains alite and calcium aluminate was synthesized, and the hydration reactivity of the cement from this clinker, gypsum and granulated slag is similar to usual portland cement, and the hydrates were mainly CSH, ettringite, and $Ca(OH)_2$.

• Resources Recycling
• /
• v.11 no.6
• /
• pp.24-30
• /
• 2002

Reduced and modified converter slag was ball milled and sieved to -200/+325 mesh. CaO,$SiO_2$, $Fe_2$$O_3$ was added to slag powder and mixed to make it similar to the composition of normal portlant cement. The pellet made of this powder was heated from $1250^{\circ}C$ to $1450^{\circ}C$ for 15 min～45 min. Most feasible condition for making slag cement clinker is the heating more than 20 min at $1450^{\circ}C$. The compressive strength of the mortar made of this slag cement clinker was better than that of normal port-lant cement in long time curing.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.04a
• /
• pp.57-61
• /
• 2000

This experimental study was carried out to estmate the effects of mixing dosage rate and blain on the compressive strength properties of antiwashout underwater concrete admixed with finely ground granulated blast furnace slag. The experimental parameters are slag contents(0, 20, 30, 40, 50, 60%). As a result the compressive strength have a high correlation with slag blended ratio. Thus, it is possible to calculate the modulus of modified age using compressive strength of antiwashout underwater concrete blended with slag.

• Journal of the Korean Ceramic Society
• /
• v.43 no.7 s.290
• /
• pp.408-414
• /
• 2006

Properties of slag cement that contained 50 wt% of blast furnace slag were studied when replaced blast furnace slag powder with electric arc furnace slag powder. Electric arc furnace slag was aged for about 2 months in the air by being crushed to be 1-3 mm in size. As a result of the experiment, it was proven that the water content for obtaining the same consistency became decreased as slag is replaced with electric arc furnace slag instead of blast furnace slag. Also, the workability of mortar increased about 30% at the same ratio of water to binder when blast furnace slag was completely replaced with electric arc furnace slag. The compressive strength of mortar on the 28 days increased when a slag replacement rate became 10 wt%, however, it rather decreased when the slag replacement rate exceeded 10 wt%. The heat of hydration became higher for the first 14 h in case of the replacement of slag cement by electric arc furnace slag. Yet, it decreased when 14 h had passed. Therefore, when all blast furnace slag was replaced with electric arc furnace slag, about 15 cal/g heat of hydration decreased when it passed about 72 h.

• Journal of the Korean Ceramic Society
• /
• v.32 no.8
• /
• pp.873-880
• /
• 1995

In order to prepare the modified belite (C2S-C4A3S-C4AF-CS) cement with low energy, clinkers were synthesized by converter slag, limestone, gypsum and clay. The synthesized clinkers were characterized and the hydration processes were investigated by XRD, SEM and microconduction calorimetry. The hydrates were mainly C-S-H and ettringite. The needle-like ettringite formed by the hydration of C4A3S at the early stage of hydration was filled in the inner vacant spaces of the hardened body and it might contribute to the rapid-hardening phenomena. The hardened body became stronger due to the hydration of C2S at the later period. The compressive strengths of the cement-3 mortars hydrated for 3, 7 and 28 days were 115, 128 and 211 Kgf/$\textrm{cm}^2$, respectively.

• International Journal of Highway Engineering
• /
• v.17 no.2
• /
• pp.1-11
• /
• 2015

PURPOSES : This study set out to investigate the fundamental properties of alkali-activated concrete (AAC) using modified slag as the pavement maintenance material. METHODS: The material properties of modified slag based alkali-activated concrete (MSAAC) were analyzed and evaluated against those of alkali-activated slag concrete (AASC). Several mix formulations were considered, including one MSACC and four AASCs. The main variables considered in the study were slump, air content, compressive strength, rapid chloride permeability test, scaling resistance, freeze-thaw test, XRD, SEM, and EDS. RESULTS: MSAAC exhibits a compressive strength in excess of 21 MPa six hours after curing. Also, the charge passed of the MSACC was found to be less than 2000 coulombs after seven days and about 1000 coulombs after 28 days. The weight loss determined from a scaling test did not exceed $1kg/cm^2$ in the case of the MSACC, but that of the AASCs had already exceeded $1kg/cm^2$ at the 10th cycle. Based on the results of the freeze-thaw test, the relative dynamic modulus of every mix was found to be in excess of 90%. An energy dispersive spectroscopy(EDS) analysis found that the weight rate percentage of the calcium and aluminum in the MSAAC mix is twice that of the AASC mixes. CONCLUSIONS : It was found that the MSAAC mix exhibits significantly better performance than AASC mixes, based on various fundamental properties.

• Applied Chemistry for Engineering
• /
• v.19 no.6
• /
• pp.652-660
• /
• 2008

For the recycling of rapid-chilled steel slag, the mechanical strengths and physical properties of EVA-polymer modified mortars with the various replacement ratios of rapid-chilled steel slag were investigated. Twenty five specimens of polymer modified mortars were prepared with the five different amounts of EVA-polymer modifier (0, 5, 10, 15, 20 wt%) and rapid-chilled steel slag (0, 25, 50, 75, 100 wt%). For the investigation of the characteristics of polymer modified mortars, the measurements such as water-cement ratio, unit volume weight, air content for fresh mortar and compressive strength, flexural strength, water absorption, hot water resistance, porosity and SEM investigation for curing specimens were conducted. As a results, with an increase in the replacement ratio of rapid-chilled steel slag, water-cement ratios decreased but unit volume weight increased remarkably. With increasing EVA-polymer modifier and the replacement ratio of rapid-chilled steel slag, percent of water absorption decreased but compressive and flexural strengths increased remarkably. By the hot water resistance test, mechanical strengths decreased but total pore volume and porosity increased remarkably. In the SEM observation, the components of specimen were shown to stick to each other in the form of co-matrix phase before hot water resistance test, but polymer modifier of co-matrix phase was decomposed or deteriorated after hot water resistance test.

• Journal of Conservation Science
• /
• v.26 no.2
• /
• pp.171-182
• /
• 2010

The slag excavated from Gyesil-ri in Gongju, Yeonje-ri in Cheongwon and Beopcheonsaji (temple) site in Wonju are analyzed by X-ray Fluorescence Analyzer, metallurgical microscope, SEM-EDS etc., for chemical composition and microstructure to figure out the raw material and the iron manufacturing technique. First of all, as a result of principal component analysis, the total Fe-content of slag from Gyesil-ri is 39 to 44% and the modified rate is 15 to 21%, which is common in ancient iron slag. Yeonje-ri site is found the ancient iron-smelting furnace. The total Fe-content of slag from Yeonje-ri is 41 to 43% and modified rate is 18~30%, which is also the general value in the ancient slag. However only slag is excavated in the residential area at Beopcheonsaji site and there is no iron making relic. In addition, the result of principal component analysis contains that the total Fe-content of Beopcheonsaji site is 52 to 57%, and modified rate is 8 to 14%. It shows that the total Fe-content of Beopcheonsaji site is higher than relic from Gyesil-ri and Yeonje-ri and the modified rate is lower than other sites. This results mean that recollecting rate of Fe in Beopcheonsaji site is lower than other sites. Also, as a result of minor elements analysis, the slag from Gyesil-ri has the higher level of Ti, V and Zr than other sites and the microstructure are observed as magnetite and ulvospinel, so that the raw material of slag is iron sand. But the slag from Yeonje-ri and Beopcheonsaji site are identified to use iron ore. As a result of microstructure observation, fayalite, gray-columnar crystal, is found in the slag from Yeonje-ri and big wustite as main phase is observed in the slag from Beopcheonsaji site. This study show that the slag from Yeonje-ri is made of smelt ash produced during smelting works and the slag from Beopcheonsaji site is made of forging ash produced during forging work concerning the excavated location and the microstructure.