• Wind and Structures
• /
• v.18 no.4
• /
• pp.347-373
• /
• 2014

Since its development in the early 1980's the force balance technique has become a standard method in the efficient determination of structural loads and responses. Its usefulness lies in the simplicity of the physical model, the relatively short records required from the wind tunnel testing and its versatility in the use of the data for different sets of dynamic properties. Its major advantage has been the ability to provide results in a timely manner, assisting the structural engineer to fine-tune their building at an early stage of the structural development. The analysis of the wind tunnel data has evolved from the simple un-coupled system to sophisticated methods that include the correction for non-linear mode shapes, the handling of complex geometry and the handling of simultaneous measurements on multiple force balances for a building group. This paper will review some of the components in the force balance data analysis both in historical perspective and in its current advancement. The basic formulation of the force balance methodology in both frequency and time domains will be presented. This includes all coupling effects and allows the determination of the resultant quantities such as resultant accelerations, as well as various load effects that generally were not considered in earlier force balance analyses. Using a building model test carried out in the wind tunnel as an example case study, the effects of various simplifications and omissions are discussed.

• Korean Journal of Optics and Photonics
• /
• v.14 no.3
• /
• pp.327-330
• /
• 2003

We present the fabrication and measured performance of a wavelength tunable Butt coupled DBR-LD. An average coupling efficiency between active layer and passive waveguide layer was measured over 85％per facet, and the average threshold current was 21 ㎃ for the waveguide integrated DBR laser. High output power of Butt coupled DBR-LD was obtained over 25 ㎽. As high as 25 ㎽ of output power was achieved by the butt coupled method. The maximum wavelength tuning range is about 7.4 nm, and the side mode suppression ratio was more than 40 ㏈ using 1.3 ${\mu}{\textrm}{m}$ InGaAsP waveguide layer.

• Korean Journal of Optics and Photonics
• /
• v.3 no.3
• /
• pp.198-202
• /
• 1992

Silver ion-exchanged glass waveguide with its large surface index difference and shallow depth is suitable to be used for the hybrid integration of semiconductor device and glass waveguide using the semiconductor film grafting technique. We report characteristics of the planar and channel glass waveguides exchanged in the diluted silver nitrate melt in the visible and infrared spectral region. Especially, we determined the fabrication parameters for single-mode channel waveguide at 1.5.$\mu$m, an important wavelength in the optical communication. Directional couplers with several different configurations were fabricated, and their 3 dB coupling length was determined as a function of wavelenGh and polarization.

• Journal of the Optical Society of Korea
• /
• v.17 no.1
• /
• pp.63-67
• /
• 2013

We perform an optical vestigial sideband (VSB) filtering using a pair of Fabry-Perot (FP) filters. The transmittance curve of each FP filter is made to have sharp skirts using an offset between input and output coupling fibers. Moreover, the accurate periodicity of FP filters in the optical frequency domain enables the simultaneous VSB filtering of a large number of optical channels. With this VSB filtering technique, we transmit 12.5-GHz spaced $64{\times}12.4-Gb/s$ wavelength-division-multiplexing channels over a single-mode fiber up to 150 km without any dispersion compensations. When the channel spacing is reduced to 10 GHz, we achieve the spectral efficiency of 1 bit/s/Hz in conventional optical intensity modulation systems up to 125 km.

• Computers and Concrete
• /
• v.27 no.4
• /
• pp.305-317
• /
• 2021

The bond between the concrete and bar is a main factor affecting the performance of the reinforced concrete (RC) members, and since the steel corrosion reduces the bond strength, studying the bond behavior of concrete and GFRP bars is quite necessary. In this research, a database including 112 concrete beam test specimens reinforced with spliced GFRP bars in the splitting failure mode has been collected and used to estimate the concrete-GFRP bar bond strength. This paper aims to accurately estimate the bond strength of spliced GFRP bars in concrete beams by applying three soft computing models including multivariate adaptive regression spline (MARS), Kriging, and M5 model tree. Since the selection of regularization parameters greatly affects the fitting of MARS, Kriging, and M5 models, the regularization parameters have been so optimized as to maximize the training data convergence coefficient. Three hybrid model coupling soft computing methods and genetic algorithm is proposed to automatically perform the trial and error process for finding appropriate modeling regularization parameters. Results have shown that proposed models have significantly increased the prediction accuracy compared to previous models. The proposed MARS, Kriging, and M5 models have improved the convergence coefficient by about 65, 63 and 49%, respectively, compared to the best previous model.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.26 no.4
• /
• pp.256-262
• /
• 2021

Six-phase motors can be used in industrial applications, such as an electric vehicle, due to their high reliability and low current magnitude per phase. An asymmetrical PMSM with two sets of three-phase windings is a commonly used structure for six-phase motors, with each winding set demonstrating a phase difference of 30°. Although the asymmetrical PMSM presents low torque ripples, its dynamic torque response deteriorates due to coupled components in the two three-phase windings. The decoupled VSD control is applied to eliminate the coupling effect. Load ratio control of two inverters for the six-phase PMSM is proposed in this study. DQ currents are controlled on the basis of two synchronous reference frames, and the six-phase drive system can be changed to a three-phase drive system when one inverter presents fault conditions. The operation and effectiveness of the proposed algorithm is verified through simulation and experiments. The six-phase drive system is transferred to a three-phase drive system by changing the current reference of the second DQ reference frame. Moreover, control of both torque and speed exhibits satisfactory performance before and after the mode change.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.27 no.5
• /
• pp.410-416
• /
• 2022

A grid-connected inverter with critical loads uses mode transfer control to supply stable voltage to the load. An islanding detection method should also be used to quickly detect the grid fault and disconnect the inverter from the grid. However using the existing islanding detection method to detect islanding is difficult due to the small fluctuation of the voltage and frequency of the point of common coupling. This study proposes a reactive power P&O islanding detection method by using the positive feedback technique. The proposed method always injects a small variation of reactive power. When a grid fault occurs, the injected reactive power accelerates the reactive power injection reference. As a result, the reactive power reference value and the sensed reactive power become mismatched, and islanding is detected. Reducing the amount of real-time injected reactive power results in high efficiency and power factor. The simulation and experimental results of a 3 kW single-phase inverter are provided to verify the proposed islanding detection method.

• ETRI Journal
• /
• v.45 no.1
• /
• pp.163-170
• /
• 2023

We report an electroabsorption modulator (EAM)-integrated distributed Bragg reflector laser diode (DBR-LD) capable of supporting a high data rate and a wide wavelength tuning. The DBR-LD contains two tuning elements, plasma and heater tunings, both of which are implemented in the DBR section, which have blue-shift and red-shift in the Bragg wavelength through a current injection, respectively. The light created from the DBR-LD is intensity-modulated through the EAM voltage, which is integrated monolithically with the DBRLD using a butt-joint coupling method. The fabricated chip shows a threshold current of approximately 8 mA, tuning range of greater than 30 nm, and static extinction ratio of higher than 20 dB while maintaining a side mode suppression ratio of greater than 40 dB under a window of 1550 nm. To evaluate its modulation properties, the chip was bonded onto a mount including a radiofrequency line and a load resistor showing clear eye openings at data rates of 25 Gb/s nonreturn-to-zero and 50 Gb/s pulse amplitude modulation 4-level, respectively.

• Wind and Structures
• /
• v.37 no.1
• /
• pp.39-56
• /
• 2023

To ensure the wind stability of a long-span suspension bridge during deck erection under skew wind, based on the aerostatic and self-excited aerodynamic force models under skew wind, a computational approach of refined flutter analysis for long-span bridges under skew wind is firstly established, in which the effects of structural nonlinearity, the static wind action and full-mode coupling etc are fully considered, and the corresponding computational procedure is programmed. By taking the Runyang suspension bridge over the Yangtze River as example, the flutter stability of the bridge in completion under skew wind is then analyzed with the aerodynamic parameters of a similar bridge deck measured from the sectional model wind tunnel test under skew wind. Finally, through simulating the girder segments erected symmetrically from the midspan to towers, from the towers to midspan and simultaneously from the towers and midspan to the quarter points, respectively, the evolutions of flutter stability limits during the deck erection under skew wind are investigated numerically, the favorable aerodynamically deck erection sequence is proposed, and the influences of skew wind and static wind effect on the flutter stability of suspension bridge under construction are ascertained.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.38 no.7
• /
• pp.14-21
• /
• 2001

In this paper, we designed and fabricated C-band bandpass filter using dielectric resonators. From waveguide cutoff frequency which applied the region between adjacent dielectric resonators, the height of cavity is determined. The cavity's diameter is determined to the twice of dielectric resonator? diameter considering the conductor loss. The resonant frequency of the DR cavity is calculated with non decaying mode analysis. Conventionally, cylindrical dielectric resonator is analysed by Cohn's model which use the decaying mode in the region between dielectric resonator wall and circular cavity wall, which is an approximated method. The external quality factor, $Q_{ex}$ has found with simulation result using Ansoft's Maxwell simulation tool. The designed filter using dielectric resonators with dielectric constant of 45 has the passband center at 5.065GHz. The bandpass filter using dielectric resonators has about 1dB insertion loss, 20MHz bandwidth and more than 30dB attenuation at $f_0+15MHz$.