• Journal of the Korean Ceramic Society
• /
• v.21 no.1
• /
• pp.19-26
• /
• 1984

This study has exemined on the effect for the fitting in porcelain body of $MgO-SiO_2$ system. The mixture was made of corresponding in the theoretical composition of enstatite with Kyul Sung talc and sea water magnesia cake. Hyup Jin kaolin as clay minerals to give the mixtue plasticity was added 10% by weight of the mixture. Also feldspar was added 5% by weight of the above mixture. We added limestone in various kinds of 1%-20% by weight of mixture included kaoil and feldspar in order last of all. The mixture was fire at the various temperatures from 12$25^{\circ}C$ to 13$25^{\circ}C$. After we examined closely physcial properties and microstructures we achieved the following results. 1) 5% addition amount of limestone was good for the property of the strength at the full firing temperatures. But 10% and 15% additions were remarkably excellant below 1275$^{\circ}C$ 2)When we considered the apparent bulk density 5% addition was good for the full firing temperature. 3) 5% addition amount of limestone was proved to be the most excellant propeties between 130$0^{\circ}C$ and 13$25^{\circ}C$ when we considered the apparent bulk density and the range of the firing temperature.

• Journal of the Korean Ceramic Society
• /
• v.31 no.5
• /
• pp.552-560
• /
• 1994

A composite of TiB2-Al2O3 system was successfully prepared from a mixture of TiO2, B2O3, and Al by self-propagating high temperature synthesis (SHS) with a novel characteristic, utilizing the internal oxidation heat of aluminium metal of the mixture, instead of by a conventional technique, externally heating a mixture of Ti, B and Al2O3. From a mixture with B/Ti molar ratio of =2.0, pure two phases of TiB2 and $\alpha$-Al2O3 with good crystallinity and small, uniform sizes were formed. However, when the B/Ti molar ratio of the mixture goes to a value less than 2.0, in addition to the above main minerals, a small smounts of metastable phases such as TiB and Ti3B4 were formed. It was found that about 60%, the optimum green density of compacts gave their highest reaction rate and temperature during SHS process. TiB2-Al2O3 system composite with B/Ti molar ratio of =2.0 could be pressurelessly sintered even at 190$0^{\circ}C$ under Ar gas flows without any addition of sintering aids, showing their good properties such as 91.2% in relative density, 2750 kgf/$\textrm{mm}^2$ in Vickers hardness and 2620 kgf/$\textrm{cm}^2$ in flexural strength.

• Communications for Statistical Applications and Methods
• /
• v.7 no.1
• /
• pp.129-140
• /
• 2000

Wavelets constitute a new orthogonal system which has direct application in density estimation. We introduce a brief wavelet density estimation and summarize some asymptotic results. An application to mixture normal distributions is implemented with S-Plus.

• The Korean Journal of Applied Statistics
• /
• v.24 no.6
• /
• pp.987-994
• /
• 2011

From the point view of credit evaluation whose population is divided into the default and non-default state, two methods are considered to estimate conditional distribution functions: one is to estimate under the assumption that the data is followed the mixture normal distribution and the other is to use the kernel density estimation. The parameters of normal mixture are estimated using the EM algorithm. For the kernel density estimation, five kinds of well known kernel functions and four kinds of the bandwidths are explored. In addition, the corresponding ROC functions are obtained based on the estimated distribution functions. The goodness-of-fit of the estimated distribution functions are discussed and the performance of the ROC functions are compared. In this work, it is found that the kernel distribution functions shows better fit, and the ROC function obtained under the assumption of normal mixture shows better performance.

• Journal of Powder Materials
• /
• v.7 no.4
• /
• pp.228-236
• /
• 2000

An investigation was carried out on the possibility whether the ball-milling process of low energy could successfully improve the packing density and flowability for MIM application in W-20wt%Cu system. In this study, W-20wt%Cu powder mixture was prepared by ball-milling. W powder was not fractured by low mechanical impact energy used in the present work during the critical ball-milling time, but the ductile Cu powder was easily deformed to the 3 dimensional equiaxed shape, having the particle size similar to that of W powder. The ball-milled mixture of W-20wt%Cu powder had the more homogeneous distribution of each component and the higher amount of powder loading for molding than the simple mixture of W-Cu powder with an irregular shape and a different size. Accordingly, the MIM W(1.75)-20wt%Cu powder compacts were able to be sintered to the relative density of 99% by sintering at $1400^{\circ}C$ for one hour.

• Journal of Powder Materials
• /
• v.11 no.6 s.47
• /
• pp.462-466
• /
• 2004

The bi-materials composed of $Al-5wt{\%}Mg$ and its composite reinforced with SiC particles were prepared by ball-milling and subsequent sintering process. The size of powder in Al-Mg/SiCp mixture decreased with increasing ball-milling time, it was saturated above 30 h when the ball and powder was in the ratio of 30 to 1. Both $Al-5wt{\%}Mg$ powders mixture and $Al-5wt{\%}Mg/SiCp$ mixture were compacted under a pressure of 350MPa and were bonded by sintering at temperatures ranging from 873K to 1173K for 1-5h. At 873k, the sound bi-mate-rials could not be obtained. In contrast, the bi-materials with the macroscopically well-bonded interface were obtained at higher temperatures than 873K. The length of well-bonded interface became longer with increasing temperature and time, indicating the improved contact in the interface between unreinforced Al-Mg part and Al-Mg/SiCp composite part. The relative density in the bi-materials increased as the sintering temperature and time increased, and the bi-materials sintered at 1173K for 5h showed the highest density.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.40 no.3
• /
• pp.23-29
• /
• 2008

This study was performed to improve the printability of Hanji using a microbial cellulose from Saprolegnia ferax through investigating the printability of Hanji sized with the mixture of the microbial cellulose and various kinds of sizing agents. Conclusions obtained from the results of this study were as follows. The proper concentration of a microbial cellulose in sizing a printable Hanji with it was 0.5%. In general, there was no remarkable effect but some effect on the opacity and ink density. Hanji was sized with the mixture(5:5) of microbial cellulose(0.5%) and AKD(1.0%). As a result, ink spread was remarkably improved by the girth reduction of ink spot. There was remarkable effect because the mixture(5:5) of a microbial cellulose(0.5%) and CMC(1.0%) improved not only the gloss but also the density and girth of ink spot. Mixing(7:3) with corn starch(3.0%) showed the smallest girth of ink spot among applied sizing agents. Mixing(7:3) with PVA(5.0%) also showed some effect in the density and girth of ink spot.

• Journal of Powder Materials
• /
• v.3 no.1
• /
• pp.49-56
• /
• 1996

The effect of$H_{2}/N_{2}$gas sintering atmosphere on the carbon content and mechanical properties during the metal injection molding process of carbonyl iron-nickel powder was studied. The carbon content of the specimen after debinding in the pure$N_{2}$atmosphere appeared 0.78 wt%. After showing the maximum value of 1.48 wt.% in the debinding atmosphere of 10%$H_{2}/N_{2}$gas mixture, the carbon content of the debinded specimen decreased gradually with increasing the$H_2$content in the$H_{2}/N_{2}$gas mixture. The carbon contents of the sintered specimen were 0.46~0.63wt% in Na gas atmosphere, while they appeared extremely low above 40%$H_{2}/N_{2}$gas atmosphere. The relative sintered density increased abruptly from 88~90% to 93~96% with the addition of Ni, while the density nearly unchanged above 2% Ni addition. The sintered density increased with increasing the fraction of$H_{2} in H_{2}/N_{2}$gas mixture. Tensile strength and hardness increased, and elongation decreased with increasing carbon and Ni content. In spite of high carbon content of 0.63 wt%, the superior elongation value of 10% was shown.

• Communications for Statistical Applications and Methods
• /
• v.8 no.3
• /
• pp.797-803
• /
• 2001

This paper obtained Bayes prediction density for the spatial linear model with non-informative prior. It showed the results that predictive inferences is completely unaffected by departures from the normality assumption in the direction of the elliptical family and the structure of prediction density is unchanged by more than one additional future observations.

• Korean Journal of Environmental Biology
• /
• v.35 no.2
• /
• pp.152-159
• /
• 2017

For the effective seedling production of the hard shelled mussel, Mytilus coruscus, this study assessed the effects of the dietary value of live food, density, water temperature and salinity on growth and survival rate of the larvae. The optimal survival rate and growth rate were examined under differing conditions of water temperature, salinity, and rearing density for 30 days. The three groups were provided different feeding organisms, such as Isochrysis galbana and Teleaulax suecica. The mixtures were provided at a rate of $5{\times}10^4cell\;mL^{-1}$. The best growth was observed in the group with conditions $21^{\circ}C$ water temperature ($16.2{\pm}9.1{\mu}m$), 33 psu of salinity ($16.82{\pm}3.9{\mu}m$), $2500individual\;m^{-2}$ ($17.2{\pm}5.9{\mu}m$), and fed with $5{\times}10^4cell\;mL^{-1}$ of I. galbana and T. suecica mixture ($16.0{\pm}7.3{\mu}m$). The highest survival rate was found in the group at conditions $18^{\circ}C$ water temperature (66.4%), 33 psu of salinity (24.4%), $2500individual\;m^{-2}$ (65.8%), and fed with $5{\times}10^4cell\;mL^{-1}$ of I. galbana and T. suecica mixture (58.8%). We therefore conclude that the suitable culture conditions for the stable production of hard shelled mussel artificial seedlings was at 18 to $21^{\circ}C$ of temperature, 30 to 33 psu of salinity, 2500 to $5000individual\;m^{-2}$ of rearing density, and feeding supplement of $5{\times}10^4cell\;mL^{-1}$ of I. galbana and T. suecica mixture under semi running water system.