• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2007년도 하계종합학술대회 논문집
• /
• pp.159-160
• /
• 2007

Two analog predsitorters (PDs) using the mixing operation are proposed to compensate for the memory effects of the power amplifier and then significantly cancel IM3 components with the independent control of IM3 terms. In the first PD, IM3 terms are generated by using mixing operation of low frequency terms. In the second PD, the double mixing operation of the fundamental components is used. For a two-tone signal with 20-MHz tone spacing, the notable IM3 suppression is achieved over a whole output power range.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2023년도 가을학술발표대회논문집
• /
• pp.189-190
• /
• 2023

In this study, the compressive strength and hydration heat of cement paste mixed with cellulose nanocrystal(CNC) and graphene oxide (GO) were evaluated. The difference was compared by mixing 0.1 vol.% ~0.4 vol.% of CNC and 0.05 wt.% ~ 0.1 wt.% of GO in a cement paste with a water cement ratio of 0.3. As a result, it was confirmed that the compressive strength increased as CNC and GO were mixed respectively, and then the compressive strength decreased when the appropriate mixing rate was exceeded. In the hydration heat measurement, there was no significant difference when only CNC was mixed, but it was confirmed that the hydration heat decreased as the amount of CNC mixing increased when used in combination with GO.

• 한국토양환경학회지
• /
• 제2권3호
• /
• pp.23-30
• /
• 1997

본 연구의 목적은 슬러리상 생물반응기를 이용한 석유계탄화수소 오염토양의 처리에 있어서 고형물함량 및 혼합강도의 영향을 평가하는 것이다. 디이젤오염토양의 슬러리상 생물학적 처리에 대한 수행결과는 실험실규모에서 얻어졌고 TPH(총 석유계탄화수소)는 생물학적 처리와 연관하여 평가되었다. TPH의 생물학적 및 비생물학적 거동은 디이젤내의 화합물에 의해 이전에 노출되지 않은 토양을 이용하여 결정되었다. 투입량에 대한 반응기부피는 고형물함량을 최대화함으로써 줄여질 수 있다. 고형물함량 50% 및 20%를 적용한 결과 생물학적 TPH 제거율에 있어서 약간의 차이(57.5%:61.6%)를 보여주었다. 혼합과 토양입자의 부유는 오염물의 탈착 및 생물학적 분해에 있어서 매우 중요하다. 이러한 관점에서 본 연구는 두가지 혼합강도를 이용하여 수행되었다. 70rpm을 이용한 반응기의 경우 20rpm을 적용한 반응기에 비하여 토양입자의 부유 및 TPH의 제거율에 있어서 더 좋은 결과를 나타내었다. 20rpm을 적용한 반응기의 경우 토양입자의 완전한 부유가 일어나지 않았다.

• Journal of the Korean Wood Science and Technology
• /
• 제25권2호
• /
• pp.33-44
• /
• 1997

This study was executed to examine the effects of polypropylene fiber length and process variables of the composites made from wood fiber and nonwood fiber mixed formulations. As a nonwood fiber the polypropylene with 3 denier thickness of tow condition was selected and cut into each length of 0.5, 1.0, 1.5, 2.0 and 2.5cm to mix with wood fiber. And also western hemlock wood fiber for medium density fiberboard was prepared. First, to decide an adequate polypropylene mixing fiber length, the composites of 1.0g/$cm^3$ density were made from 10% polypropylene fiber by each of five lengths and 90% western hemlock fiber mixed formulations. Thereafter as the experiments of process variable, the composites applied with adequate polypropylene fiber length(1.5cm) were made from 4 density levels (0.6, 0.8, 1.0, 1.2g/$cm^3$). 3 mixed formulations of wood fiber to polypropylene fiber(95 : 5, 90 : 10, 85 : 15), and 3 mat moisture contents(5, 10, 20%). According to the results and discussions it was concluded as follows ; The physical and mechanical properties were shown improved tendency. as polypropylene fiber length was increased in the range from 0.5 to 1.5cm, but shown decreasing tendency from 2.0 to 2.5 cm. Accordingly, it was shown that polypropylene fiber length is limited to 1.5cm or less length in mixing wood fiber and polypropylene fiber by turbulent air mixing process. As the densities of wood fiber-polypropylene fiber composites were increased, the physical and mechanical properties were clearly improved. Also they were shown significantly increasement statistically between densities respectively. In the mixed formulations, physical and mechanical properties were shown only slightly improvement, as they changed from 95 : 5 to 85 : 15 in wood fiber to polypropylene fiber. Despite of increasement of mat moisture content, mechanical properties were not improved significantly but physical properties were improved somewhat in wood fiber-polypropylene fiber composites.

• 유기물자원화
• /
• 제22권2호
• /
• pp.50-56
• /
• 2014

일반적으로 도금 폐수를 비롯한 산업 폐수 내 중금속 처리에 적용되는 응집-침전은 응집제의 비용과 침전 효율의 불안정성이라는 한계가 존재한다. 본 연구에서는 수산화물 생성-분리막 공정을 전제로 하여, pH와 교반조건에 따른 수용액 상의 중금속 제거 효율과 생성된 수산화물의 입도 분포를 고찰하였다. pH별 실험 결과, pH 9-10에서 최적의 중금속 제거 효율이 확인되었으며, 무기응집제인 $FeCl_3$의 투입은 오히려 제거 효율을 저하시켰다. 완속교반 시간 및 강도는 70 rpm, 20 min 조건이 최대 효율을 보였으며 Cu, Ni, Zn 모두 청정 지역 기준 폐수 배출 기준을 만족하였다. 나타났다. 생성된 중금속 수산화물의 입도 분석을 수행한 결과, 입자의 99.9 %가 $2{\mu}m$ 이상이었다.

• 대한기계학회논문집B
• /
• 제28권7호
• /
• pp.818-825
• /
• 2004

In this paper, the study of effects of flow parameters on flame structure and NOx emission concentration was performed in co-axial. laminar partially premixed methane/air flames. Such (low parameters as equivalence ratio(${\Phi}$), fuel split percentage($\sigma$), and mixing distance(x/D$\_$i/) were defined as a premixing degree and varied within ${\Phi}$=1.36∼9.52, $\sigma$=50∼100, and x/D$\_$i/=5∼20. The image of OH$\^$*/ and NOx concentration were obtained with an ICCD camera and a NOx analyzer. The flame structure observations show a categorization of partially premixed flames into three distinct flame regimes corresponding to ${\Phi}$<1.7(premixed flame structure), 1.7<${\Phi}$<3.3(hybrid structure), and ${\Phi}$>3.3(diffusion flame structure existing a luminous sooting region) at $\sigma$=75%, and x/D$\_$i/=10. As o decreases from 100% to 50%, and x/D$\_$i/ decreases, nonpremixed flame structure appear at low equivalence ratio relatively. In addition, the measured emissions for NOx rise steeply from ${\Phi}$=1.7, to ${\Phi}$=3.3, then constants ${\Phi}$>4.76. NOx emissions decrease with increase the level of premixing level. In conclusion, the main effect on flame structure and NOx production was at first equivalence ratio(${\Phi}$), and next fuel split percentage($\sigma$), and finally mixing distance(x/D$\_$i/).

• 대한기계학회논문집
• /
• 제18권3호
• /
• pp.690-700
• /
• 1994

The effects of thermal stratification on the flow of a stratified fluid past a circular cylinder were examined in a wind tunnel. In order to produce strong thermal stratifications, a compact heat exchanger type variable electric heater is employed. Linear temperature gradient of up to $250^{\circ}C/m$ can be well sustained. The velocity and temperature profiles in the cylinder wake with a strong thermal gradient of $200^{\circ}C/m$ were measured and the smoke wire flow visualization method was used to investigate the wake characteristics. It is found that the temperature field effects as an active contaminant, so that the mean velocity and temperature profiles can not sustain their symmetricity about the wake centerline when such a strong thermal gradient is superimposed. It is evident that the turbulent mixing in the upper half section is stronger than that of the lower half of the wake in a stably stratified flow.

• 대한기계학회논문집
• /
• 제10권1호
• /
• pp.70-77
• /
• 1986

본 논문에서는 재순환 영역이 존재하는 축대칭 난류 확산화염 구조예측의 전 단계로서, 이미 발표된 바있는 필자의 실험 데이터를 바탕으로 하여 등온유동에 서의 난류모델을 검토한다. 유선의 곡률이 큰 유동에 2방정식 모델을 적용함은 큰 결점을 보완한 수정-2방정식모델을 채택하여 실험결과와 비교, 검토하여 모델의 타당성을 조사하였다.

• 한국응용과학기술학회지
• /
• 제26권3호
• /
• pp.335-340
• /
• 2009

This study investigates the paste mixing of positive active materials which, affect the life cycle of batteries in Pb-Ca-Sn grids, and generation of 4BS in a curing process and considers the effects of these things on the initial charge characteristics and life cycle. In the results of the experiments applied in this study, it was possible to reduce the curing time in which the fine 4BS was formed by the mixing of the positive active materials of lead acid battery applied at high temperature compared to that of the existing coarse 4BS and that represented some improvements in the life cycle performance.

• 한국자동차공학회논문집
• /
• 제10권2호
• /
• pp.31-39
• /
• 2002

Recently, many researches have been performed to improve the performance of the combustion and emission in a D.I.Diesel engine. One of the main factors effect on the characteristics of combustion is the characteristic of air-fuel mixing. Thus, swirl flow has been used widely to improve the air-fuel mixing in a D.I.Diesel engine. Since this swirl flow has interaction with other factors, in this study, the characteristics of the combustion and the flame effected by the swirl flow generated by SCV was investigated. From this experiment, the interactions of the swirl flow and the injection timing made clear. In addition, the effects of swirl and injection timing on the diffusion flame were clarified.