• Journal of the Optical Society of Korea
• /
• 제15권1호
• /
• pp.96-102
• /
• 2011

Simultaneous measurements using a scanning spectrograph system and transmissometer were performed for the first time over an urban site in Gwangju, Korea, to derive the ambient $NO_2$ volume mixing ratio. The differential slant column densities retrieved from the scanning spectrograph system were converted to volume mixing ratios using the light traveling distance along the scanning line of sight derived from the transmissometer light extinction coefficients. To assess the performance of this system, we compared the derived $NO_2$ volume mixing ratios with those measured by an in situ chemiluminescence monitor under various atmospheric conditions. For a cloudless atmosphere, the linear correlation coefficient (R) between the two data sets (i.e., data derived from the scanning spectrograph and from the in situ monitor) was 0.81; the value for a cloudy atmosphere was 0.69. The two sets of $NO_2$ volume mixing ratios were also compared for various wind speeds. We also consider the measurement errors, as estimated from an error propagation analysis.

• 한국유기농업학회지
• /
• 제31권4호
• /
• pp.309-325
• /
• 2023

GMO labeling system in South Korea stipulates three labeling methods: GMO labeling, no labeling and Non-GMO labeling. Products labeled as Non-GMO are not allowed for unintentional commingling of GMO without tolerance. However, consumers vary their acceptance of Non-GMO label on the unintentionally commingled products and willingness to pay according to the mixing rate, rather than devalue the whole products as useless. Additionally, consumers do not believe that the acceptable mixing rate should be discriminated between non-labeled products, which allow up to 3% of unintentional GMO contamination, and Non-GMO labeled products. Information on unintentional GMO mixing mainly refers to the mixing rate, but the Non-GMO content remaining even after commingling is also important information. The decline in value is alleviated when consumers are exposed to positive information, such as Non-GMO content, rather than when exposed to negative information, such as the mixing rate. Loss Aversion Coefficient is relative depending on whether the information representing the loss is positive or negative. Information that a Non-GMO labeled product contains X% GMO is more sensitive than information that (100-X)% Non-GMO remains.

• 한국정보통신학회논문지
• /
• 제8권6호
• /
• pp.1234-1242
• /
• 2004

채널 간격이 균등한 WDM(Wavelength Division Multiplexing) 시스템에서 4-광파 혼합(FWM ; Four-Wave Mixing)의 영향을 가장 많이 받는 중간 채널의 MSSI(Mid-Span Spectral Inversion)를 통한 보상 특성을 채널 입력 전력, 광섬유 분산 계수, 전송 거리 변화에 따라 살펴보았다. MSSI를 위한 전체 전송 링크 중간에 위치한 광 위상 공액기의 비선형 매질로는 광대역 전송을 가능하게 하는 HNL-DSF(Highly Nonlinear Dispersion Shifted fiber)를 사용했다. 우선 변조 파형의 형식에 상관없이 WDM 시스템의 광섬유 분산 계수가 클수록 FWM에 의한 채널 간섭의 영향을 줄일 수 있다는 것과 이 경우 WDM 채널 수에 상관없는 고전력 전송은 변조 파형 형식으로 RZ를 사용함으로써 가능하다는 것을 알 수 있었다. 그러나 WDM 채널 수 변동에 대한 유연한 시스템 구축을 위해서는 변조 파형 형식으로 NRZ를 사용하는 것이 유리하다는 것을 확인하였다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제22권6호
• /
• pp.24-29
• /
• 2018

콘크리트 자기치유를 목적으로 미생물 혼입 하이드로젤 지지체 첨가에 따른 콘크리트의 특성을 검토하였다. 자기치유 콘크리트의 슬럼프 측정결과, 모든 배합조건에서 목표슬럼프를 만족하였으나, 하이드로젤 지지체의 혼입량 증가에 따라 슬럼프 감소가 있었다. 하이드로젤 지지체 혼입에 따른 공극률의 변화는 미미하였다. 자기치유 콘크리트의 압축강도 평가결과, 하이드로젤 지지체의 혼입은 강도에 영향을 미치지 않았다. 하지만 동일 배합조건하에서 시험체간의 분산값이 하이드로젤 지지체 혼입량 증가에 따라 증가하는 경향을 나타내었다. 하이드로젤 지지체의 혼입에 따른 자기치유 콘크리트의 투수시험 결과, HC-B1.5 배합의 경우 최대 45.6%의 투수계수 회복율을 나타내어 하이드로젤 지지체의 혼입이 투수계수 감소에 효과가 높은 것으로 확인되었다.

• 대한기계학회논문집
• /
• 제7권3호
• /
• pp.278-285
• /
• 1983

The momentum transfer in axisymmetric turbulent boundary layer over a rotating cone submerged in a free stream was studied by experiments and numerical analysis. In numerical analysis the velocity profiles were calculated by finite difference method using Prandtl mixing length concept, and the results were compared with experimental results. The agreement was good. By the numerical analysis the wall fircition coefficient was increased as the Reynolds number increased when the rotational speed is large, but the wall friction coefficient was decreased as the rotational speed increased.

• Nuclear Engineering and Technology
• /
• 제52권9호
• /
• pp.1945-1954
• /
• 2020

Subchannel code is one of the effective simulation tools for thermal-hydraulic analysis in nuclear reactor core. In order to reduce the computational cost and improve the calculation efficiency, empirical correlation of turbulent mixing coefficient is employed to calculate the lateral mixing velocity between adjacent subchannels. However, correlations utilized currently are often fitted from data achieved in central channel of fuel assembly, which would simply neglect the wall effects. In this paper, the CFD approach based on spectral element method is employed to predict turbulent mixing phenomena through gaps in 3 × 3 bare tight lattice rod bundle and investigate the flow pulsation through gaps in different positions. Re = 5000,10000,20500 and P/D = 1.03 and 1.06 have been covered in the simulation cases. With a well verified mesh, lateral velocities at gap center between corner channel and wall channel (W-Co), wall channel and wall channel (W-W), wall channel and center channel (W-C) as well as center channel and center channel (C-C) are collected and compared with each other. The obvious turbulent mixing distributions are presented in the different channels of rod bundle. The peak frequency values at W-Co channel could have about 40%-50% reduction comparing with the C-C channel value and the turbulent mixing coefficient β could decrease around 25%. corrections for β should be performed in subchannel code at wall channel and corner channel for a reasonable prediction result. A preliminary analysis on fluctuation at channel gap has also performed. Eddy cascade should be considered carefully in detailed analysis for fluctuating in rod bundle.

• 콘크리트학회논문집
• /
• 제17권4호
• /
• pp.595-602
• /
• 2005

본 연구는 건설 폐기물로 발생하는 폐 콘크리트에서 분리한 재생골재의 투수성 포장 재료로서의 유효이용을 위하여 포러스 콘크리트의 재생골재 혼입률과 폴리머분산제의 혼입률에 따른 역학적 특성 및 내구성을 평가하였다. 시험결과, 포장용 포러스 콘크리트의 공극률 및 투수계수는 재생골재의 혼합비율이 증가함에 따라 다소 증가하고 폴리머 혼입률 증가에 따라 감소하는 경향을 나타내었으나 폴리머를 $20\%$혼입한 경우 국내 포장용 투수 콘크리트에 관한 규정($8\%$ 및 0.01cm/sec)을 만족하였으며, 압축강도 및 휨강도는 재생골재의 혼입률이 증가함에 따라 감소하였으나, 폴리머의 혼입률이 증가함에 따라 크게 증가하는 경향을 나타내어 폴리머를 $10\%$ 이상 혼입하면 재생골재를 $75\%$ 혼합$\cdot$사용한 경우에도 국내 포장 콘크리트에 관한 규정(18MPa 및 4.5MPa 이상)을 만족하였다. 또한 미끄럼저항성은 재생골재의 혼입률이 증가에 따라 BPN값은 증가하였으나, 폴리머를 혼입함에 의해 BPN값은 감소하는 경향을 나타내었으며, 내마모성 및 동결융해저항성은 쇄석골재만을 사용한 경우에 비해 재생골재의 혼합비율이 증가함에 따라 감소하였으나, 폴리머를 혼입한 경우에는 현저히 개선되어 폴리머를 $10\%$ 혼입한 경우 혼입하지 않은 경우에 비하여 내마모성 및 내동해성은 각각 약 $8.6\%$ 및 3.8배정도 개선되는 것으로 확인되었다.

• 한국건축시공학회지
• /
• 제1권2호
• /
• pp.174-178
• /
• 2001

This study was performed to control the thermal crack of the mat footing slab in the multi-purposed buildings. In this study, we executed the mixing design of concrete to satisfy the workability and the quality according to the site conditions. And, we evaluated quantitatively about the possibility of thermal crack by using hydration heat analysis system. Finally, we proposed the optimal mixing conditions, curing methods and curing period which all factors are considered. As a result, the optimal mixing conditions were : W/B 41%, unit binder 375kgf/$\textrm{m}^3$, FA replacement ratio 20%. Lowest thermal stress was 22.0kgf/$\textrm{cm}^2$ and at that time thermal crack index was over 1.5, when the coefficient of thermal conductivity was lowest among the curing conditions. And, the total curing time was estimated at 6.7 days according to curing steps.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 봄 학술발표회 논문집
• /
• pp.533-538
• /
• 2001

This study was peformed to control the thermal crack of the mat footing slab in the multi-purposed buildings. In this study, we executed the mixing design of concrete to satisfy the workability and the quality according to the site conditions. And, we evaluated quantitatively about the possibility of thermal crack by using hydration heat analysis system. Finally, we proposed the optimal mixing conditions, curing methods and curing period which all factors are considered. As a results, the optimal mixing conditions were : W/B 41%, unit binder 375kg/$cm^{2}$, FA replacement ratio 20%. Lowest thermal stress was 22.0kgf/$cm^{2}$ and at that time thermal crack index was over 1.5, when the coefficient of thermal conductivity was lowest among the curing conditions. And, the total curing time was estimated at 6.7 days according to curing steps.

• 콘크리트학회논문집
• /
• 제12권1호
• /
• pp.33-44
• /
• 2000

Since the mechanism of chloride diffusion and its ratio in concrete depend on structural conditions and concrete as a micro-structure, if these are analyzed quantitatively, the long-term ageing of structures can be predicted. Although, a quantitative analysis of concrete micro-structure, in which the results are affected by various parameters, is very difficult, this can be done indirectly by the durability test of concrete. In this study, the compressive strength, void ratio and air permeability of concrete. In this study, the compressive strength, void ratio and air permeability of concrete are chosen as the parameters in concrete durability test, and these effects on test results are analysed according to changes of mixing properties. The relationships between parameters and chloride diffusion velocity is used for prediction models of chloride diffusion. The developed prediction models for the chloride diffusion according to mixing and physical properties, can be used to estimate the service life and corrosion initiation of reinforcing bars in marine structures.