• 공업화학
• /
• 제10권2호
• /
• pp.218-224
• /
• 1999

원자로 정지시 혼상 탈염기의 최적 운전방법을 제안할 목적으로 산성-산화성 분위기에서 저농도의 Ni, Co 및 Ag 이온이 함유된 모의 냉각재 용액의 연속식 이온교환특성을 연구하였다. 금속 이온의 제거 용량에 미치는 양이온 교환수지 형태의 효과로서 $H^+$형 수지의 성능은 $Li^+$형 수지의 성능보다 약 6% 정도 높은 것으로 나타났다. 혼합층 이온교환 방법인 양이온과 음이온 수지의 혼합은 비혼합시와 비교하여 금속 이온들의 제거 용량에는 영향을 미치지 않았으나 금속 이온들의 파과곡선의 기울기를 매우 조금 증가시켰다. 냉각재의 산성-산화성 분위기와 관계된 영향으로서 붕산의 첨가는 금속 이온들의 파과곡선의 기울기를 매우 작게 감소시킨 반면, 과산화수소의 첨가는 금속이온들의 제거 용량을 약간 감소시켰다.

• 생약학회지
• /
• 제1권3호
• /
• pp.93-99
• /
• 1970

There have been reported by several workers for the isolation and determination of the amine derivatives as Metbylephedrine Hydrochloride and Ephedrine Hydrochloride adopting neutralization method, steam distillation method, non-aqous titration method, ion-exchange resin method, titration method after acetylation, colorimetric method, gravimetric method, iodine titration method and gas chromatography. Those methods mentioned in above, can be practically applied for the sample which is not mixed one mith the other amine compounds. Presently, it has not shown on the isolative determination of the mixed sample of amine derivatives. In this paper, it is discussed on the isolative determination of Methylephedrine Hydrochloride as the tertiary amine compound and Ephedrine Hydrochloride as the secondary amine compound. According to the results of the experiment, it could be summarized as follows: 1. There is no time-variation on the color reaction of Methylephedrine Hydrochloride and Ephedrine Hydrochloride with the color reagent, bromcresolgreen. And Methylephedrine Hydrochloride and Ephedrine Hydrochloride, respectively, can be determined spectrophotometrically by means oft his color reaction. 2. For the isolation of Methylephedrine Hydrochloride and Ephedrine Hydrochloride from the mixed sample, Methylephedrine Hydrochloride can be eluted by chloroform, while Ephedrine Hydrochloride by the mixed solvent of chloroform and ethylalcohol (2:1), from the celite column adsorbed at pH6.4 followed by extraction with ether undersodium hydroxide alkali re action. 3. When the sample is mixed with quinine hydrochloride, dihydrocodeine bitartate, and noscapine, these mixed compounds can be eliminated by means of stram distillation. 4. When the sample is mixed with chlorpheniramine maleate, dextromethorphan hydrobromide and diphenhydramine hydrochloride, the mixed compounds can be eliminated by means of steam distillation and celite adsorption column chromatography, In conclusion, the isolative determination method for Methylephedrine Hydrochloride and Ephedrine Hydrochloride studied in this paper, indicates with the excellent reproducibility and accuracy.

• 한국재료학회지
• /
• 제22권12호
• /
• pp.643-649
• /
• 2012

Coatings composited with alumina and Perfluoro alkoxyalkane (PFA) resin were deposited on stainless steel plate (SUS304) to further improve corrosion resistance. Plate (ca. $10{\mu}m$) and/or nanosize (27~43 nm) alumina used as inorganic additives were mixed in PFA resin to make alumina-fluoro composite coatings. These coatings were deposited on SUS304 plate with wet spray coating and then the film was cured thermally. According to the amount and ratio of the two kinds of alumina having plate morphology and nano size, corrosion resistance of the film was evaluated under strong acids (HF, HCl) and a strong base (NaOH). The film prepared with the addition of 5~10 wt% alumina powders in PFA resin showed corrosion resistance superior to that of pure PFA resin film. However, for the film prepared with alumina content above 10 wt%, the corrosion resistance did not improve with the physical properties, such as surface hardness and adhesion. The film prepared with plate/nanosize (weight ratio = 1/2) alumina especially enhanced the surface hardness and corrosion resistance. This can be explained as showing that the plate and the nanosize alumina dispersed in PFA resin effectively suppressed the penetration of cations and anions due to the long penetration length and fewer defects that accompany the improved surface hardness under a serious environment of 10% HF solution for over 120 hrs.

• 대한소아치과학회지
• /
• 제25권2호
• /
• pp.259-267
• /
• 1998

For more than two decades, many investigators have tried a variety of methods for delivering antimicrobial agents to the oral cavity with the objective of eliminating mutans streptococci. In the belief that the effectiveness of chemotherapy might be improved by a more effective delivery system, the intention of the present study was to exploit a new drug delivery system delivering chlorhexidine to the oral cavity. The vehicle delivering chlorhexidine tested in this study was self-curing acrylic resin(polymethyl methacrylate). The powder of the acrylic resin was polymerized with the 5 different liquid preparations, in which $Chlorzoin^{(R)}$ was mixed with five different monomer/Chlorzoin ratios immediately prior to the polymerization, in a stainless steel mold ($40mm{\times}40mm{\times}2mm$). A total of 50 cured resin specimens were divided into 5 groups according to the different monomer preparations. Every specimen was soaked in an airtight container filled with distilled water (100 ml) and then kept in an incubator at $37^{\circ}C$. The solutions (0.8 ml) were collected from the container at every 24 hours, and the amount of released chlorhexidine in the solutions was measured in an ultraviolet spectrophotometer at 250nm. The container was refilled with distilled water every after measurement. This procedure was repeated for 14 days. It was found that chlorhexidine was continuously released from all of the 50 specimens during the experimental period. And it was noted that the pattern of chlorhexidine release was a type of sustained-release preparation, that is, the amount of the released chlorhexidine at the first day in all 5 groups was high (p<0.0001), and then the release was decreased during the rest of the experimental period (p<0.001).

• 디지털융복합연구
• /
• 제18권4호
• /
• pp.309-314
• /
• 2020

Polymethyl methacrylate (PMMA)는 치과 교정장치 재료로 사용해 왔다. 하지만 낮은 항균력으로 인한 구강감염을 촉진시킬 염려가 있다. 본 연구에서는 이를 극복하기 위하여 최근 발표된 Ag-MSN, graphene-oxide nanosheets(nGO), Cerium nanoparticle(CNP)의 나노입자를 교정레진인 Dentarum 회사의 Orthocryl를 사용하여 레진 파우더 대비 중량비 0, 0.25, 0.5, 1.0, 2.0%를 MMA 액에 혼합한 후 제조사의 지시에 따라 PMMA 분말: MMA 액 (1.2 : 1) 비율로 혼합하여 교정용 시편을 제작하였고 교정용 레진 항진균 실험, 통계분석을 하였다. 항균실험을 한 결과 교정용 PMMA레진이 Ag-MSN을 함유할 때 항(진)균적 성질이 증가하였다. nGO를 PM에 넣으면 표면이 거칠어지고 친수성을 높일 수 있었고 항균 접착제 효과가 표면 거칠기의 변화가 아닌 친수성이 증가하였다. CNP 농도가 높을수록 항부착 성질이 최대 60%까지 관찰되었다. 나노입자함유 교정용 레진은 항균효과가 나타남을 알 수 있었다. 이는 의치, 치열 교정 장치 및 임시 수복물에 대한 유망한 항균 치과 재료로서의 잠재적 유용성을 시사한다.

• Journal of Electrical Engineering and Technology
• /
• 제13권3호
• /
• pp.1166-1172
• /
• 2018

Degradation due to delamination occurs frequently in the high temperature superconductors (HTS) coil of rotating machines made with 2nd generation (2G) HTS wire, and the authors have observed other similar cases. Since an HTS field coil for a rotating machine is required to have stable current control and maintain a steady state, co-winding techniques for insulation material and epoxy resin for shape retention and heat transfer improvement are applied during coil fabrication. However, the most important limiting factor of this technique is delamination, which is known to be caused by the difference in thermal expansion between the epoxy resin and 2G HTS wire. Therefore, in this study, the experimental results of mixing the ratio of epoxy resin and alumina ($Al_2O3$) filler were applied to the fabrication of small and large test coils to solve the problem of degradation. For the verification of this scheme, eight prototypes of single pancake coils with different shapes were fabricated. They showed good results. The energization and operation maintenance tests of the stacked coils were carried out under liquid neon conditions similar to the operation temperature of an MW-class rotating machine. In conclusion, it was confirmed that the alumina powder mixed with epoxy resin in an appropriate ratio is an effective solution of de-lamination problem of 2G HTS coil.

• Restorative Dentistry and Endodontics
• /
• 제40권1호
• /
• pp.30-36
• /
• 2015

Objectives: This study was performed to determine whether the combined use of one-bottle self-etch adhesives and composite resins from same manufacturers have better bond strengths than combinations of adhesive and resins from different manufacturers. Materials and Methods: 25 experimental micro-shear bond test groups were made from combinations of five dentin adhesives and five composite resins with extracted human molars stored in saline for 24 hr. Testing was performed using the wire-loop method and a universal testing machine. Bond strength data was statistically analyzed using two way analysis of variance (ANOVA) and Tukey's post hoc test. Results: Two way ANOVA revealed significant differences for the factors of dentin adhesives and composite resins, and significant interaction effect (p < 0.001). All combinations with Xeno V (Dentsply De Trey) and Clearfil $S^3$ Bond (Kuraray Dental) adhesives showed no significant differences in micro-shear bond strength, but other adhesives showed significant differences depending on the composite resin (p < 0.05). Contrary to the other adhesives, Xeno V and BondForce (Tokuyama Dental) had higher bond strengths with the same manufacturer's composite resin than other manufacturer's composite resin. Conclusions: Not all combinations of adhesive and composite resin by same manufacturers failed to show significantly higher bond strengths than mixed manufacturer combinations.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2005년도 제17회 워크샵 및 추계학술대회
• /
• pp.554-557
• /
• 2005

The bipolar plate is a major component of the PEM fuel cell stack, which takes a large portion of stack cost. In this study, as alternative materials for bipolar plate of PEM fuel cells, graphite composites were fabricated by compression molding. Graphite particles mixed with epoxy resin were used as the main substance to provide electric conductivity. To achieve desired electric properties, specimens made with different mixing ratio, processing pressure and temperature were tested. To increase mechanical strength, one or two layer of woven carbon fabric were added to the original graphite and resin composite. Thus, the composite material is consisted of the three phases: graphite particles, epoxy resin, and carbon fabric. By increasing mixing ratio, fabricated pressure and process temperature, electric conductivity was improved. The results of tensile test showed that the tensile strength of two-phase graphite composite was about 5MPa, and that of three-phase composite was increased to 54MPa.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2005년도 춘계 학술기술논문발표대회 논문집
• /
• pp.125-131
• /
• 2005

Recently, to improve condition car park, using surface finishing material for variety color and property epoxy resin, urethane, cement mixed resin mortar or polymeric resin, and so on. However, it is frequent noise and wear out of tier and waterproofing materials, when the car slip or stop in car park, To minimize these cases, It is necessary that reduction of repair cost through performance long term durability of surface finishing material, improvement inside condition such as reduce dirty and car accident and ensurance the expected life of concrete slab in car park. Especially, we have not any tech for quality control, construction tech, production technology for car park surface materials, that's why park slab is not safety and suffer a loss. For this problems, this paper is to test surface finishing materials and as that result, suggest quality standard in the car park.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 춘계학술대회 논문집
• /
• pp.824-828
• /
• 2000

As production cycle has become more and more shorter, the demand of rapid prototyping technology has increased largely. There are many methods for rapid prototyping technology, such as SLA. SLS, FDM. INK JET, LOM and so on. Of all methods, SLA has been most widely used for fabricating precision parts. But products manufactured by this method have limitation of single color and single material. So the principal purpose of this study is to overcome the limit of single color product. If the internal structure of manufactured product is visible with multi-color characteristic, it is possible to check easily the designed model with reality. In order to give multi-color characteristic to the product, photocurable resin mixed with pigment is used in this study. First, transparency of photocurable resin without pigment is evaluated, and then color characteristic and curing characteristic of the mixture is evaluated changing mixing ratio. Through the basic experiments, it becomes possible to fabricate multi-color 3D prototype without assembly.