• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2011.11a
• /
• pp.245-246
• /
• 2011

In recent research in this emerging and latent heat storage material features an innovative temperature - controlled Phase Change Materials to evaluate the superior thermal performance would like to calculate the thermal conductivity. Specified in KS F 4040 test specimen dimensions were equivalent in specifications, test methods according to KS L 9016 was an experiment in progress. As a result, the thermal conductivity of plain cement mortar mixed with more PCM came out with low thermal conductivity of mortar, thermal performance was excellent.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.05a
• /
• pp.609-617
• /
• 2003

The use of Shotcrete(Sprayed concrete) for the support of underground excavations was pioneered by the Civil engineering industry. Permanent shotcrete tunnel linings such as Single-shell, NMT(Norwegian Method of Tunnelling) have been constructed in many countries for reducing construction time and lowering construction costs instead of conventional in-situ concrete linings. Among essential technologies for successful application of Permanent Shotcrete Linings, high performance shotcrete having high strength, high durability, better pumpability has to be developed in advance. This paper presents the ideas and the first field test results of wet-mixed Steel Fiber Reinforced Shotcrete(SFRS) with powder types cement mineral accelerator. From the results, wet-mix SFRS with powdered accelerator exhibited good early strength improvement and less rebound ratio compared to the ordinary accelerator.

• Journal of the Korean Geotechnical Society
• /
• v.16 no.2
• /
• pp.79-89
• /
• 2000

The application of stabilization method has increased because of short construction periods, no environmental problems with dumped and replaced soil, assurance of required strength and economical effect with mid to small size construction. The unconfined and triaxial(UU-condition) compression tests were executed with each mixing sample for the study of the improvement effects and the effect of design-parameters by the stabilization methods. Three typical stabilizers, which are representative in Korea, were applied in this study, and three common soils(very soft clay, general weathered soil, common clay), which are common in Korea, were used in this study. In this study, the effect of engineering factors(soils, stabilizers and water contents, etc.) which are important parameters for the improvement effects of mixed ground by stabilizers, was analyzed. As results, the tendencies of design-parameters(unconfined compression strength, deformation modulus and strength parameter) are presented and the criteria of the application of stabilization methods are suggested.

• Journal of the Korea Institute of Building Construction
• /
• v.4 no.2
• /
• pp.89-95
• /
• 2004

1) As result of specimen with shear reinforcing bar of reinforced concrete beam, ductile coefficient of specimen was high in specimen containing Cockle shells based on non-mixed specimen. In increase rate of specimens, yield strength was similar in specimens containing Cockle shells and non-mixed specimens and maximum strength was higher in specimen containing Cockle shells. 2) To sum up the above experimental results, it is found that using splitted Cockle shells as aggregate for concrete by 10%～ 15% showed the same or higher compressive strength and shear strength as concretes using general aggregate and it can be used as substitute aggregate of concrete. It is considered that for future use of splitted Cockle shells as substitute concrete aggregate, continuous researches of its durability, applicability and economy are needed.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.326-330
• /
• 2009

In this study, coarse-grained geomaterials were mixed with cementing binder. To do that, typical soils from road construction sites were selected to assess the strength and stiffness characteristics of cemented geomaterials mixed with cement and recycled fly ash. Mechanistic evaluation on these samples was performed depending on the various binder contents. Increasing cementing content tend to increase the resilient modulus under repeated loadings and unconfined strength respectively. In addition, the toughness of cemented geomaterials was also estimated in order to check the ability to resisting fatigue failure.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.05a
• /
• pp.138-139
• /
• 2018

This study is a basic review of the basic characteristics of mortar as a result of the use of concrete as a fine aggregate for CGS(coal gasification slag) generated from the IGCC(integrated gasification combined cycle). The analysis shows that CGS and crushed sand + seal sand mix is the best combination of CGS combined with about 75 % of CGS based on the effects of promoting liquidity and strength. This is expected to be a positive factor in securing the strength and flexibility of concrete given the optimal mix of CGS, and may also contribute to the improvement of quality.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.05a
• /
• pp.17-18
• /
• 2019

In this study, the initial strength reduction of coal gasification slag fine powders was confirmed through previous studies when used in cement formulations. It is also confirmed that the blast furnace slag is mixed with cementitious coal blast furnace slag, which is similar to coal gasification slag, to incorporate gypsum in order to prevent initial strength deterioration. In order to analyze the reactivity of coal gasification slag by desulfurization gypsum, the formation of hydrates and their reactivity at early ages were confirmed by electron microscope. In order to confirm the reactivity, the gypsum samples were prepared with unincorporated type and 2% mixed type. Experimental results showed that 2% of the desulfurized gypsum specimens reacted more actively than the uninjured ones.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.11a
• /
• pp.108-109
• /
• 2018

Cement is the most widely used but generates a lot of CO₂, so we need a material to replace it. Using industrial by-products such as Silica Fume(SF), Blast furnace Slag(BS) and Fly Ash(FA) bring some advantages including CO₂ reduction and resource recycling. However, there is a limit to improve performance when using only one material. Therefore, the synergy effects of No cement binary mortar and ternary mortar were analyzed and compared. As a result, No cement ternary mortar had the strength higher than binary mortar. among ternary mortars, the specimen mixed 50% of BS had the highest strength. However, when SF was mixed by 20%, the flowability reduces. so 10% of SF, 40% of FA and 50% of BS is considered as the optimal mixing ratio.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2009.11a
• /
• pp.19-22
• /
• 2009

The Study has analyzed the overall material properties, the measurement of forming colors and applicability of color concrete through making color concrete using red mud heated at 800℃mixed with existing pigment and applying it to the actual field. As the results, the slump flow and aeration meet the target value and the compressed strength of the concrete mixed with red mud and pigment is higher than that of the plain. In addition, the measurement of forming colors turn out to be satisfactory and the color forming is excellent. In the field application, the color concrete panel is proved to make sure the beauty of store exits through its various design available.

• Journal of the Korea Institute of Building Construction
• /
• v.15 no.3
• /
• pp.351-357
• /
• 2015

Fiber reinforced concrete (FRC) has been successfully used to enhance the flexural toughness of concrete. As fibers are randomly oriented in FRC, they sometimes produce clumps that reduce the mechanical performance, and a properly chosen mixing protocol can be a way to minimize this problem. In this research, the effects of mixing method on the mechanical properties of FRC were investigated. The compressive strength, flexural strength, and flexural toughness were measured using three different mixing methods. It was shown from the results that the compressive strength and peak flexural load were not affected by changes in mixing method. However, in terms of flexural toughness, the changes in mixing method clearly affected the flexural toughness of FRC. The truck-mixed FRC outperformed two pan-mixed FRCs.