• Journal of the Korea institute for structural maintenance and inspection
• /
• v.11 no.2
• /
• pp.109-116
• /
• 2007

The purpose of this paper is to evaluate the fire resistant performances of load-bearing wall using both composite and steel stud panel infilled with light-weight formed mortar under axial loading according to KS F 2257(1999). The minimum requirement of 2 hours fire resistant rating is needed for the residential and commercial buildings under the fire regulation of Korea. From test results, it is found that two types of specimen composed of the hybrid stud and steel stud panel filled with light-weight formed mortar fited in with the requirement of 2 hours fire resisting rate for the load-bearing wall. In the conclusions, the specimen with hybrid stud shows predominating fire-resistant performance on the adiabatic effects rather than that of the steel stud specimen.

• Journal of the Korea Institute of Building Construction
• /
• v.15 no.1
• /
• pp.1-7
• /
• 2015

The objective of this study is to develop a high-performance foamed concrete made with a new mixture proportioning as an alternative of autoclaved lightweight concrete (ALC) block. For the early-strength gain of the foamed concrete under an atmospheric curing condition, the binders and chemical agents were specially contrived as follows: 3% anhydrous gypsum was added to ordinary portland cement (OPC) in which $3CaO{\cdot}SiO_2$ content was controlled to be above 60%; and the content of polyethylene glycol alkylether in a polycarboxylate-based water-reducing agent was modified to be 28%. Using these binders and chemical agents, 11 mixes were prepared with the parameters of W/B ratio (30% to 20% in a interval of 2.5%) and unit binder content ($400kg/m^3$ to $650kg/m^3$ in a interval of $50kg/m^3$). The quality and availability of the mixed foamed concrete were examined according to the minimum requirements specified in the KS for ALC block and existed conventional foamed concrete. The measured properties satisfied the minimum requirement of KS for ALC block and proved that the developed high-performance foamed concrete had considerable potential for practical application.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.4
• /
• pp.1626-1634
• /
• 2015

LCL filters are widely used in three-phase PWM converter for its advantages of small volume, low cost and inhibition of high frequency current harmonic. However, it is difficult to optimize its design because its parameters are mutually influenced while the value of each parameter for LCL filter has impacts on the converter's cost and size. In this paper, the target of optimization is to minimize the parameter values of LCL filter, and an optimization method for parameters of LCL filter of three-phase PWM converter based on least square method is proposed. With this method, a quantitative calculation of the harmonic component of the converter’s side phase voltage is performed first, and then the quantitative relationship between phase voltage harmonics and grid phase current harmonics is analyzed. After that, the attenuation requirement of each harmonic is obtained by taking into account the requirements for each harmonic component of grid current. Then according to the optimization objective, the objective function with minimum harmonic attenuation deviation is established, and least squares method is adopted for three-dimensional global searching of parameters for LCL filter. Thus, the designed harmonic attenuation curve approximates the minimum attenuation requirements, and the optimized LCL filter parameters are obtained. Finally, the effectiveness of the method is verified by the experiments.

• Korean Journal of Human Ecology
• /
• v.20 no.3
• /
• pp.691-711
• /
• 2011

This study examines the preliminary license and approval facilitation standards for improvements in quality for childcare centers focusing on the number of children, building space standards, facilities and equipment, and childcare program. Data from 48 caese was collected from childcare centers nationwide in Korea through a questionnaire and building plan. The first step for starting care licensing is to work out the ages and numbers of children within four or five age ranges. The second step is to work out the number of children as small, medium, or large considering staff to child ratios and building size. The Nnext step is to make a choice about childcare service quality classification as minimum, fair, or good, considering space requirements per child for the building, the classroom and the outdoor playground. The next step is to make a choice of space organization relating to service programs, considering the sleeping and eating area, indoor play area, toilet & washing facilities, classroom layouts such as cluster type, double zone type, single zone type, and others. Also, each room and entrance, office, kitchen, storage, laundry, teacher's area, and chilldren's area, need to be checked for space requirements and performances. The last step is to arrange the childcare program with the building and site plan. In conclusion childcare service quality will get better by upgrading of license regulation especially in minimum space requirements per child, corresponding with an increase in GNP and housing area per person. This is needed for childcare licensing in order to determine the quality level of childcare service.

• Journal of Biosystems Engineering
• /
• v.20 no.3
• /
• pp.245-249
• /
• 1995

In this study power requirements to saw shoots with circular saw were determined by measuring and analyzing the required maximum torque to provide the information for the mechanization of Korean pine cone harvest. Two levels of feed rate of shoots, 10.4mm/s and 20.8mm/s, three levels of sawing speed 5.8㎧, 11.6㎧, and 17.4㎧, and 14 levels of shoot diameter from 7.7 to 18.1mm were used as variables. 1) The maximum torques were significantly affected by all three variables. The average maximum torque, 18.2 N-cm for feed rate of 20.Bmm/s was greater as much as 80% of 10.1 N-cm for feed rate of 10.4mm/s. 2) As the sawing speed was increased from 5.8㎧ to 11.6㎧ and 17.4㎧, the maximum torques were decreased to 14.8N-cm, 8.5N-cm, and 7.IN-cm, respectively when the feed rate was 10.4mm/s. The maximum torque ranged from 4.5 to 19.3N-cm as shoot diameter increased from 7.7 to 18.1mm. The minimum power requirements to saw shoots of 18.1mm with circular saw was 30W for the feed rate of 10.4mm/s. 3) The maximum torques were 28.6N-cm, 14.6N-cm, and 11.4N-cm when sawing speeds were 5.8㎧, 11.6㎧, and 17.4㎧, respectively when the feed rate was 20.8mm/s and these torques were increased as much as 93%, 36%, and 61% of those for the feed rate of 10.4mm/s. The maximum torque increased from 9.7N-cm to 30.7N-cm as shoot diameter increased from 7.7 to 18.1mm. The minimum power requirements to saw shoots of 18.1mm was 54W which was 1.8 times of 30W for the feed rate of 10.4mm/s.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.3C
• /
• pp.248-255
• /
• 2002

An RF module in compliance with the IEEE 802.11a standard has been designed and its performance has been measured. Conventional heterodyne architecture with 580MHz intermediate frequency has been realized. Measurement results show that the receiver has a low Noise Figure of 5dB, the maximum gain of 70dB, and dynamic range as wide as 61dB. Also, the SAW filter used for channel selection in the IF section allowed minimum inter-channel interference. in addition to satisfying the RF output power requirement, the transmitter features its output P1dB as high as 34dBm so that the high peak-to-average ratio of the Orthogonal Frequency Division Multiplexing (OFDM) modulation scheme can be handled with minimum nonlinear distortion. The output P1dB of 34dBm of the transmitter corresponds to back-off powers of 18dB and 11dB with respect to the output power for the low and the middle frequency bands, respectively.

• Journal of Communications and Networks
• /
• v.11 no.1
• /
• pp.26-35
• /
• 2009

In this paper, we investigate how to do resource allocation to guarantee a minimum user data rate at low signaling overhead in multi-cell orthogonal frequency division multiple access (OFDMA) wireless systems. We devise dynamic resource allocation (DRA) algorithms that can minimize the QoS violation ratio (i.e., the ratio of the number of users who fail to get the requested data rate to the total number of users in the overall network). We assume an OFDMA system that allows dynamic control of frequency reuse factor (FRF) of each sub-carrier. The proposed DRA algorithms determine the FRFs of the sub-carriers and allocate them to the users adaptively based on inter-cell interference and load distribution. In order to reduce the signaling overhead, we adopt a hierarchical resource allocation architecture which divides the resource allocation decision into the inter-cell coordinator (ICC) and the base station (BS) levels. We limit the information available at the ICC only to the load of each cell, that is, the total number of sub-carriers required for supporting the data rate requirement of all the users. We then present the DRA with limited coordination (DRA-LC) algorithm where the ICC performs load-adaptive inter-cell resource allocation with the limited information while the BS performs intra-cell resource allocation with full information about its own cell. For performance comparison, we design a centralized algorithm called DRA with full coordination (DRA-FC). Simulation results reveal that the DRA-LC algorithm can perform close to the DRA-FC algorithm at very low signaling overhead. In addition, it turns out to improve the QoS performance of the cell-boundary users, and achieve a better fairness among neighboring cells under non-uniform load distribution.

• Weed & Turfgrass Science
• /
• v.6 no.1
• /
• pp.61-66
• /
• 2017

The appropriate level of irrigation for turfgrasses is vital to the performance of the turfgrass as well as conservation of water. Linear gradient irrigation system (LGIS) facilitates long-term study of turf performance under continuous irrigation gradients at extreme ends of the irrigation scale. The objectives of this study were to: a) determine the minimum irrigation requirements and relative drought resistance in three warm season turfgrasses; and b) evaluate the medium to long-term effects of irrigation levels on turf persistence, weed invasion, and susceptibility to diseases. Results suggest that grasses differed in drought resistance and persistence under variable irrigation regimes. Irrigation (Ep) required for consistent acceptable turf quality for respective grasses was Cynodon dactylon x C. transvaalensis (61%), Zoysia matrella L. Merr (73%), and Stenotaphrum secundatum 'Palmetto' (86%). Brown patch infection was most prevalent in Stenotaphrum secundatum 'Palmetto' at 12 and 125% Ep irrigation. Cynodon dactylon x C. transvaalensis and Zoysia matrella L. Merr were better able to adapt to the various irrigation regimes, and this ability allowed these species to resist drought, and maintain turf coverage which in turn, kept weeds and the occurrence of diseases at bay. Ranking these grasses for their drought tolerance abilities showed that Cynodon dactylon x C. transvaalensis had the most outstanding resistance against drought, followed by Zoysia matrella L. Merr, and lastly, Stenotaphrum secundatum 'Palmetto'. Despite having the highest irrigation requirement, Stenotaphrum secundatum 'Palmetto' was still not able to maintain persistence at high irrigation regimes. Likewise, this grass also lost turf coverage at low irrigation levels.

• Journal of Aerospace System Engineering
• /
• v.14 no.2
• /
• pp.1-11
• /
• 2020

Detecting obstacles and generating a suitable path to avoid obstacles in real time is a prime mission requirement for UAVs. In areas, close to buildings and people, detecting obstacles in the path and estimating its own position (egomotion) in GPS degraded/denied environments are usually addressed with vision-based Simultaneous Localization and Mapping (SLAM) techniques. This presents possibilities and challenges for the feasible path generation with constraints of vehicle dynamics in the configuration space. In this paper, a near real-time feasible path is shown to be generated in the ORB-SLAM framework using a chain-based path planning approach in a force field with dynamic constraints on path length and minimum turn radius. The chain-based path plan approach generates a set of nodes which moves in a force field that permits modifications of path rapidly in real time as the reward function changes. This is different from the usual approach of generating potentials in the entire search space around UAV, instead a set of connected waypoints in a simulated chain. The popular ORB-SLAM, suited for real time approach is used for building the map of the environment and UAV position and the UAV path is then generated continuously in the shortest time to navigate to the goal position. The principal contribution are (a) Chain-based path planning approach with built in obstacle avoidance in conjunction with ORB-SLAM for the first time, (b) Generation of path with minimum overheads and (c) Implementation in near real time.

• Tunnel and Underground Space
• /
• v.17 no.1 s.66
• /
• pp.1-8
• /
• 2007

In Norway, about 30 subsea tunnels have been constructed over the last 20 years. The minimum depth of 17 subsea tunnels is 56 m and rock cover are between 23 and 49 m. As the project areas for subsea tunnel are covered by water, special investigation techniques need to be applied and the investigation results are more uncertain than that of most conventional tunnel projects. The indefinite potential of water inflow and the salinic character of ingress water represent considerable problems for tunnel equipment and rock support materials. The least stable conditions are represented by major faults or weakness zones containing heavily crushed rock and clay gouge. This paper introduces the Oslofjord subsea tunnel project including minimum rock cover requirement, risk of water inflow, investigation costs, construction costs, and traffic & operation costs.