• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.1022-1027
• /
• 2004

In this study, the shape of plate-fin type heat sink is numerically optimized to acquire the minimum pressure drop under the required temperature rise. To do this, a new sequential approximate optimization (SAO) is proposed and it is integrated with the computational fluid dynamics (CFD). In thermal/fluid systems for constrained nonlinear optimization problems, three fundamental difficulties such as high cost for function evaluations (i.e., pressure drop and thermal resistance), the absence of design sensitivity information, and the occurrence of numerical noise are confronted. To overcome these problems, the progressive quadratic response surface method (PQRSM), which is one of the sequential approximate optimization algorithms, is proposed and the heat sink is optimize by means of the PQRSM.

• Journal of Korean Society for Quality Management
• /
• v.16 no.2
• /
• pp.99-110
• /
• 1988

This study is concerned with a design algorithm to minimize the investment as well as maximize the throughput in automated warehouse system. A simulation model is designed and a solution methodology is proposed. The experiment, are conducted for the cases with 100, 90, 80, 70, 60, 50 and 0 % dual command policies in terms of the important factors such as the crane velocity, the height of system and the rack utilization. The results indicate that the throughput is slightly decreased when the ratio of dual command is decreased and the other characteristics however are not affected. The result also shows that the optimal rack should be designed for a crane to take the same amount of travel time for horizontal and vertical movement.

• Korean Management Science Review
• /
• v.23 no.2
• /
• pp.161-174
• /
• 2006

In this paper, we consider a network optimization problem arising from the deployment of BcN access network. BcN convergence services requires that access networks satisfy QoS meausres. BcN services have two types of traffics : stream traffic and elastic traffic. Stream traffic uses blocking probability as a QoS measure, while elastic traffic uses delay factor as a QoS measure. Incorporating the QoS requirements, we formulate the problem as a nonlinear mixed-integer Programming model. The Proposed model seeks to find a minimum cost dimensioning solution, while satisfying the QoS requirement. We propose two local search heuristic algorithms for solving the problem, and develop a network design system that implements the developed heuristic algorithms. We demonstrate the computational efficacy of the proposed algorithm by solving a realistic network design problem.

• Journal of the Korean Operations Research and Management Science Society
• /
• v.22 no.3
• /
• pp.59-80
• /
• 1997

Designing highly survivable interoffice telecommunication networks is considered. The problem is formulated as a minimum-cost network design problem with three node connectivity constraints. These valid and facet-defining inequalities for the convex hull of the solution are presented. A branch and cut algorithm is proposed based on the inequalities to obtain the optimal solution. With the lower bound by the cutting plane algorithm, a delete-ink heuristic is proposed to otain a good upper bound in the branch and bound procedure. The effeciveness of the branch and cut algorithm is demonstrated with computational results for a variety of problem sets : different lower bounds, two types of link costs and large number of links. The cutting plane procedure based on the three inequalities provides excellent lower bounds to the optimal solutions.

• Journal of National Security and Military Science
• /
• s.9
• /
• pp.257-282
• /
• 2011

In this paper, we propose an architecture design of military operation system utilizing cellular networks. The main contribution of this paper is to provide a cost-effective military operation solution for ground forces, which is based on IT(information technology). By employing the cellular phones of officers' and non-commissioned officers' as the tools of operational communication, the proposed system can be constructed in the minimum duration and be built on the four components: command and control system, gateway, security system, and terminal(cell phone). This system is most effective for the warfare of limited area, but the effectiveness does not decrease under the total war covering the whole land of Korea. For the environmental change of near future, expanded architecture is also provided to utilize the functionalities of smart phones.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.7 no.4
• /
• pp.135-141
• /
• 2008

Independent suspension axle and final reduction gear for special-purpose vehicles such as a armored vehicles are almost imported in Germany etc. so, developing them is necessary to save cost. In severe condition (open fields, water surface driving, obstacle pass), special-purpose vehicles must work well. Drop box, axle and final reduction gear performed static analysis. We know that is possible weight reduction. The purpose of this paper is to find out the optimal shape of final reduction gear's case by means of response surface methodology. The response surface method is the statistical method which can be applied to the non-sensitivity based optimization. The response surface which is constructed by the least square method contains only the polynomial terms so that the global maximum and minimum points are easily obtained.

• Proceeding of EDISON Challenge
• /
• 2015.03a
• /
• pp.428-441
• /
• 2015

Corresponding to the high consumption rate of the selfie stick for cell phone camera, the design of the product is becoming diverse. However, relatively low cost selfie stick models are not strong enough to stand the weight of the cell phone. This results into a bending of the stick or the accidental fall of the cell phone by the failure of the holding unit. As a solution to the problem, design of selfie stick that is structurally strong enough to stand the weight of the cell phone with the minimum weight for the portability is proposed in this paper.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.755-761
• /
• 2003

Recently, the development of mobile devices demands information storage systems to use micro drive devices and cheap media. These should have several characteristics, for example, the subminiature of size, the robustness of shock, the minimum of cost and power consumption, and the removability of multiple applications. A conventional optical disk drive is more suitable for these specifications than the others. The optical storage system of the new generation to use a blue laser and a high numerical aperture (NA) is the perfect candidate for micro optical disk drives. In this paper, the micro actuator that can be applied to a micro optical disk drive is designed by response surface methodology to use a structural analysis and an electro-magnetic analysis. Based on above results, the coarse actuator and fine actuator are designed and improved from the point of view of the size and the power. Consequently, the designs of a micro actuator are proposed through these courses.

• International Journal of Automotive Technology
• /
• v.7 no.3
• /
• pp.283-288
• /
• 2006

A mathematical methodology is proposed for designing nozzle hole shapes producing controlled geometric cavitation. The proposed methodology uses an unstructured RANS flow solver, with the ability to compute sensitivity derivatives via an adjoint algorithm. The adjoint formulation for the N-S equations is presented while variation of the turbulence viscosity is not taken into account during the geometry modifications. The sensitivities are calculated in a mode independently of the shape parameterisation. The method is used to develop and evaluate conceptual shapes for nozzle hole cavitation reduction. The localized region at the hole inlet producing cavitation, is parameterised using its radius of curvature, while a cost function is formulated to eliminate the negative pressures present at this location. Sensitivity derivatives are used to assess the dependence of the localized region on the minimum pressure, and to drive the geometry to the targeted shape. The results show that the computer model can provide nozzle hole entry shapes that produce predefined flow characteristics, and thus can be used as an inverse design tool for nozzle hole cavitation control.

• International Journal of Internet, Broadcasting and Communication
• /
• v.14 no.3
• /
• pp.63-68
• /
• 2022

Two wavelength reconfigurable optical nodes are designed. One for 20km or shorter link length, and the other for up to 60km link length. While the first one requires no dispersion compensation, the latter needs dispersion compensation fiber included in the node, which requires additional optical amplifier to compensate the insertion loss of DCF. We calculate all the optical path losses in both cases using the typical value of optical components in the market to see the feasibility of the designed optical node. The minimum received power in the node is calculated to be -21.5dBm without DCF and -12.5dBm with DCF, respectively. These received powers are above the receiver sensitivity both for OC-48 and OC-192 according to the previous work.