• 한국음향학회:학술대회논문집
• /
• 한국음향학회 1993년도 학술논문발표회 논문집 제12권 1호
• /
• pp.259-262
• /
• 1993

In this paper, a new pitch beginning point detection method by extracting the G-peak, is proposed. By the speech production model, the area of the first peak on a pitch interval of speech signals is emphasized. By using the above characteristics, this method have more advantages than the others for pitch beginning point detection. The defective decision caused by an impulsive noise is minimized and the pre-filtering is not necessary for this method, because the integration of signals takes place in the process.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2002년도 학술대회 논문집
• /
• pp.330-333
• /
• 2002

This study is concerned with the optimal design of DC reactor type high-Tc superconducting fault current limiter(SFCL) by Newton method. What should be first thought over in developing SFCL is the condition in which the cost function is minimized under given constraints. So, this condition is supposed to be the values corresponding to the variables the cost function counts on. In this paper, we got the result for the SFCL available at the level of 6.6kV-200A by means of simulation.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1998년도 추계종합학술대회 논문집
• /
• pp.787-790
• /
• 1998

In this paper, we presents a method for multi-level logic mainmization which is suitable for the minimization of look-up table type FPGAs. A pattern extraction algorithm is minimized AND/XOR multi-level circuits. The circuits apply to Roth-Karp decomposition which is most commonly used technique in the FPGA technology mapping. We tested the FPGA synthesis method using pattern extraction on a set of benchmark. The proposed method achieved reductions on the number of LUTs in mapping soultion as compared with MISII(or SIS) or previous results〔5〕

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2011년도 추계학술대회
• /
• pp.193-194
• /
• 2011

This paper describes a control method to minimize the filter capacitor of a PFC AC/DC converter for LED driver. The rectified secondary voltage of the transformer has 120Hz ripple unlike the conventional converter for the LED drive. Therefore, the filter capacitor can be minimized and this provides reduced cost, low switching loss, and long life of the converter.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2011년도 전력전자학술대회
• /
• pp.9-10
• /
• 2011

This paper describes a control method to minimize the filter capacitor of a AC/DC converter for LED driver. The rectified secondary voltage of the transformer has 120Hz ripple unlike the conventional converter for the LED drive. Therefore, the filter capacitor can be minimized and this provides reduced cost, low switching loss, and long life of the converter.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.1006-1009
• /
• 2000

In this study, a multi-step optimization technique combined with a simple genetic algorithm is introduced in order to minimize the static compliance, the dynamic compliance, and the weight of a high speed machining center simultaneously. Dimensional thicknesses of the eight structural members on the static force loop are adopted as design variables. The first optimization step is a static design optimization, in which the static compliance and the weight are minimized under some dimensional and safety constraints. The second step is a dynamic design optimization, where the dynamic compliance and the weight are minimized under the same constraints. After optimization, the weight of the moving body only was reduced to 57.75% and the weight of the whole machining center was reduced to 46.2% of the initial design respectively. Both static and dynamic compliances of the optimum design are also in the feasible range even though they were slightly increased than before.

• International Journal of CAD/CAM
• /
• 제6권1호
• /
• pp.193-198
• /
• 2006

Plunge milling is the fastest way to mill away large volumes of metal in the axial direction. The residual volume (inaccessible volume by the plungers) is minimized when selecting a specific direction of filling. This direction is known as the optimal inclination angle for filling of the plunged area. This paper proposes a new algorithm to calculate the optimal inclination angle of filling and to fill the plunged area with multi-plungers sizes. The proposed algorithm uses the geometry of the 2D area of the shape that being cutting to estimate the optimal inclination angle of filling. It is found that, the optimal inclination angle for filling of the plunged area is the same direction as the longer width of the equivalent convex polygon of the boundary contour. The results of the tested examples show that, the residual volume is minimized when comparing the proposed algorithm with the previous method.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.1144-1149
• /
• 2008

Converting technology has developed to print information for the decades. Recently, this technology (like gravure, gravure-offset) is rising as an alternative way for mass production of printed electronics such as RFID, solar cell. For the width of printing line is under 10 microns, registration error should be minimized less than several microns. Tension disturbance is main cause of registration error and this should be minimized before the substrate is transported into printing zone. With PI controller, it is possible to suppress the disturbance within 2% of operating tension. But register error appears more than 10 micron using PIcontroller considering noise. So LQG controller is needed as an alternative control method. In this paper, the comparision of PI and LQG controller in the converting machine including measured noise and tension disturbance is presented. It is shown that the LQG controller is more suitable for precision tension control in printed electronics.

• Journal of Advanced Marine Engineering and Technology
• /
• 제16권1호
• /
• pp.47-53
• /
• 1992

This paper is discussing the Optimum Structural Modification by the Sensitive Analysis Method. The mokificxation for the first Mouth Open Mode of the C type structure was done by using coordinate sensitivities and thickness sensitivities. The results obtained are as follows; 1. the vibration could be minimized by reducing multiples of mode components of impact point and response point. 2. the tooling precision of the Press machine could be minimized by reducing relative vibration amplititutes between the tool and the object to be tooled. 3. the mode componets of 2 points could be identified by using the coordinate sensitivites for the C type structure. 4. the mode components of 2 points could be iodentified by using the thickness sensitivities for the C type structure.

• 한국분말재료학회지
• /
• 제9권4호
• /
• pp.251-260
• /
• 2002

In the viscosity measurement of PIM feedstock, slip correction methods require a number of experiments and produce a high level of error. In this study, a rotational rheometer with a parallel-discs configuration having different surface roughness was tried to minimize the effect of the slip phenomenon. Disc surface was prepared in 3 different roughness conditions - a smooth and 2 roughened surfaces. Results with the roughened surfaces were compared with the results obtained with a slip correction method. Relationship between powder characteristics such as size and shape and a surface roughness of the disc was examined for feedstock of 4 different powders with a same binder. As results, the effect of the slip phenomenon could be sufficiently minimized on the roughened surface in most cases. However, the effect of the slip phenomenon could not be sufficiently minimized for feedstock of a round-particular-shape powder and in the case of very narrow gap size.