• Progress in Superconductivity
• /
• v.6 no.2
• /
• pp.124-128
• /
• 2005

Homogeneous and fine powders for Bi-2223 tape were prepared by ultrasonic spray pyrolysis (SP) method from an aqueous solution of metal nitrates. Bi-2223 precursor powders were synthesized with various solutes concentration and pyrolysis temperature. The synthesized precursor powders had a narrow particle size distribution and an average particle size was $\~{\cal}um$. The reactivity of precursor powder by SP method is very high, attributed to the fine and narrow particle size distribution. Bi-2223/Ag tape was prepared using PIT method and followed by various sintering conditions. The precursor powder by SP method promoted a very quick formation of the Bi-2223 phase for short sintering time while the secondary phase such as large AEC phase and $Ca_2PbO_4$ were minimized for SP tapes.

• IEIE Transactions on Smart Processing and Computing
• /
• v.5 no.5
• /
• pp.319-322
• /
• 2016

We propose a parametric blind deconvolution method for bi-level images with unknown intensity levels that estimates unknown parameters for point spread functions and images by minimizing a penalized nonlinear least squares objective function based on normalized correlation coefficients and two regularization functions. Unlike conventional methods, the proposed method does not require knowledge about true intensity values. Moreover, the objective function of the proposed method can be effectively minimized, since it has the special structure of nonlinear least squares. We demonstrate the effectiveness of the proposed method through simulations and experiments.

• Journal of Mechanical Science and Technology
• /
• v.19 no.10
• /
• pp.1885-1890
• /
• 2005

The contour method relies on deformations that occur when a residually stressed component is cut along a plane. The method is based on the elastic superposition principle. When plasticity is involved in the relaxation process, stress error in the resulting measurement of residual stress would be caused. During the cutting the specimen is constrained at a location along the cut so that deformations are restrained as much as possible during cutting. With proper selection of the constraining location the plasticity effect can also be minimized. Typical patterns of longitudinal welding residual stress state were taken to assess the plasticity effect along with constraining locations.

• Korean Journal of Computational Design and Engineering
• /
• v.12 no.6
• /
• pp.441-451
• /
• 2007

In this paper, the method to modify a surface through three dimensional vector field technique is presented, In this method two guide surfaces are required as a shape reference. One is the shape of original surface, the other is the target shape for the result surface. Proposed method is consists of two steps. The first step is to calculate the mapping points on original and target guide surfaces so that the shape error may be minimized. The second step is to construct the smooth vector field from mapping points of the first step. The developed method is applied to shoe design system which makes the surface modeling very easy and effective.

• International Journal of Control, Automation, and Systems
• /
• v.4 no.5
• /
• pp.660-667
• /
• 2006

This paper presents a novel region-based snake method for vessel segmentation. According to geometric shape analysis of the vessel structure with different scale, an efficient statistical estimation of vessel branches is introduced into the energy objective function, which applies not only the vessel intensity information, but also geometric information of line-like structure in the image. The defined energy function is minimized using the gradient descent method and a new region-based speed function is obtained, which is more accurate to the vessel structure and not sensitive to the initial condition. The narrow band algorithm in the level set framework implements the proposed method, the solution of which is steady. The segmentation experiments are shown on several images. Compared with other geometric active contour models, the proposed method is more efficient and robust.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.31 no.8
• /
• pp.33-38
• /
• 1982

This paper deals with the simplification of the transfer function in a frequency domain, viz. the integral of the squared errors between the original and the simplified model is minimized and the latter is estimated by the Walsh function. It tries to minimize the errors between the frequency responses of the two functions. This method is compared with the existing method by means of a numercal example. The frequency response of this simplified model approximates closely to that of the original model. The proposed method is simpler in analysis and easier in implementation than the existing methods. Though the Walsh function can be easily generated with the discrete values, it has errors because its zero crossings are not continuous. This method aims at the reduction of the errors in the real parts and the imaginary parts of the two functions by dividing into the more sub-intervals, and selecting the reduced-order model according to the response of the model. As a result, it can be applied for the simplification of higher order functions into lower order functions and for the design of control systems.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.4
• /
• pp.255-261
• /
• 2004

This paper presents an improved droop method which minimizes the voltage droop of a parallel-connected power supply Conventionally, the droop method has been used to achieve a simple structure and no-interconnections among power sources. However, it has a trade-off between output voltage regulation and load sharing accuracy In this paper, the droop is minimized with a current and droop gain control using steady-stage estimation. The proposed method can achieve both good voltage regulation and good load sharing. A design example of two 10㎸, 100㎃ parallel modules is made and tested to verify the proposed current-sharing method.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2254-2255
• /
• 2008

Thermoforming is one of the most versatile and economical process to produce polymer products. The drawback of thermoforming is difficult to control thickness of final products. Temperature distribution affects the thickness distribution of final products, but temperature difference between surface and center of sheet is difficult to decrease because of low thermal conductivity of ABS material. In order to decrease temperature difference between surface and center, heating profile must be expressed as exponential function form. In this study, Finite Difference Method was used to find out the coefficients of optimal heating profiles. Through investigation, the optimal results using Finite Difference Method show that temperature difference between surface and center of sheet can be remarkably minimized with satisfying Temperature of Forming Window.

• Proceedings of the Acoustical Society of Korea Conference
• /
• 1994.06a
• /
• pp.1009-1014
• /
• 1994

This paper improves the previously proposed spectral mapping method for supervised speaker adaptation in which a mapped spectrum is interpolated from speaker difference vectors at typical spectra based on a minimized distortion criterion. In estimating these difference vectors, it is important to find an appropriate number of typical points. The previous method empirically adjusts the number of typical points, while the present method optimizes the effective number by rank reduction of normal equation. This algorithm was applied to a supervised speaker adaptation for Korean word recognition using the templates form a prototype male speaker. The result showed that the rank reduction technique not only can automatically determine an optimal number of code vectors, but also slightly improves the recognition scores compared with those obtained by the previous method.

• Journal of Korea Multimedia Society
• /
• v.25 no.5
• /
• pp.670-675
• /
• 2022

This study proposes an improved binarization method to improve image recognition rate. The research goal is to minimize the information loss that occurs during the binarization process, and to transform the object of the original image that cannot be determined through the transformation process into an image that can be judged. The proposed method uses a stepwise segmentation method of an image and divides blocks using prime numbers. Also, within one block, a trapezoidal type of fuzzy is applied. The fuzzy trapezoid is binarized by dividing the brightness histogram area into three parts according to the degree of membership. As a result of the experiment, information loss was minimized in general images. In addition, it was found that the converted binarized image expressed the object better than the original image in the special image in which the brightness region was tilted to one side.