• Journal of the Korean Academy of Esthetic Dentistry
• /
• v.6 no.1
• /
• pp.32-38
• /
• 1997

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.2
• /
• pp.103-117
• /
• 2010

In this study, the heart rate variability(HRV) signal of operating patient was acquired according to anesthesia progress and identified to evaluation possibility of depth of anesthesia in each anesthesia stage. The HRV signal was analyzed time-frequency domain applied to Wigner-Ville distribution method, the characteristic parameters were extracted for evaluation of depth of anesthesia in each anesthesia stage. The progress of general anesthesia was divided into the states of pre-operation, induction of anesthesia, operation, awaking and post-operation.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.8
• /
• pp.2785-2788
• /
• 2012

• The Magazine of the Society of Air-Conditioning and Refrigerating Engineers of Korea
• /
• v.17 no.6
• /
• pp.686-695
• /
• 1988

An algorithm and a computer program were developed for the operational simulation of office building cooling system. Using this computer program, the following results were obtained. ${\bullet}$ There is a critical number of coil rows in AHU with which the cooling system can be operated in maximum efficiency. ${\bullet}$ Energy conservation can be achieved in an office building through TAB(Testing Adjusting and Balancing) of zone air volumes.

• Korean Journal of Cleft Lip And Palate
• /
• v.7 no.2
• /
• pp.141-150
• /
• 2004

The cleft lip and palate charity operation team visited Binh Duong General Hospital in Vietnam from 17th Dec to 25th Dec 2004. Total 25 cleft lip and palate patients (male : female = 15:10) were undergone the operation. The mean age of the patients was 13.6 year. The types of surgical operation were primary cheilorrhaphy (8 cases), primary palatorrhaphy(10 cases), pharyngoplasty(2 cases), scar revision(3 cases), alveolorrhaphy(2 cases). There were no intraoperative and immediate postoperative complications. The year 2004 was the 10th charity operation in the same area so it is meaningful to review the start of this charity mission and the course, and the future of our activity.

• Proceedings of the KIEE Conference
• /
• 2004.11c
• /
• pp.741-743
• /
• 2004

In this paper, we describe a Control Element Drive Mechanism(CEDM) operation test using a Power Controller. By testing, we can catch the mechanical and electrical characteristics of CEDM and obtain the information about the improvement of CEDM and the design of CEDM power cabinet. The power controller for CEDM introduced in this paper can input firing angles directly into gate drive circuits of thyristors so that this method can be used to derive the maximum and minimum values of firing angles within available limits for a 3-phase half-wave rectifier. Angle inputs help us understand each coil's response characteristics. Since this power controller generates a serial sequence for CEDM insertion and withdrawal operations, we may judge whether CEDM works correctly as expected or not in each phase of a step movement.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.3
• /
• pp.97-103
• /
• 2001

This paper has focused on the Optimization of the cutting parameters for urning operation based on the Taguchi method. Four cutting parameters. nemely, cutting speed, feed depth of cut and nose radius are optimized with consideration of the surface roughness. The design and analysis of experiments are conducted to study the performance characteristic. The effects of these parameters on the surface roughness have been investigated using signal-to-noise(S/N) ratio and analy-sis of variance(ANOVA). The experiments have been performed using coated tungsten carbide inserts without any cutting fluid. Experimental results illustrate the effectiveness of this approach.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.271-274
• /
• 2001

In this paper, we propose a charge pump phase-locked loop (PLL) with multi-PFD which is composed of a sequential phase frequency detector(PFD) and a precharge PFD. When the Phase difference is within - $\pi$ ∼ $\pi$ , operation frequency can be increased by using precharge PFD. When the phase difference is larger than │ $\pi$ │, acquisition time can be shorten by the additional control circuit with increased charge pump current. Therefore a high frequency operation, a fast acquisition and an unlimited error detection range can be achieved.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.10a
• /
• pp.242-248
• /
• 2000

This paper has focused on the optimization of the cutting parameters for turning operation based on the Taguchi method. Four cutting parameters, namely, cutting speed, feed, depth of cut and nose radius are optimized with consideration of the surface roughness. The design and analysis of experiments are conducted to study the performance characteristic. The effects of these parameters on the surface roughness have been investigated using the signal-to-noise (S/N) ratio, analysis of variance (ANOVA). The experiments have been peformed using coated tungsten carbide inserts without any cutting fluid. Experimental results illustrate the effectiveness of this approach.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.13 no.4
• /
• pp.601-611
• /
• 2010

Currently, a life cycle cost estimates(LCCE) is the most important factor in weapon system acquisition process. However, operation and maintenance(O&M) cost related studies are insufficient from the previous literature survey. O&M cost consists of various cost factors such a man power, maintenance and direct & indirect support costs. We have known that spare-parts cost is a key factor in the O&M cost. In this paper, we developed the spare-parts cost estimating relationships(CERs) of fixed-wing aircraft and armored vehicle weapon systems which include 4 historical cost drivers ; system acquisition cost, deterioration rate, localization rate, mission characteristic. Furthermore, we proposed the application methodologies that O&M cost estimating, total life cycle cost estimating and determination of the economic life using the spare-parts CERs.