• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.2
• /
• pp.393-400
• /
• 2015

As the development and distribution of the intelligent transport system is spreading recently and some of the services are commercialized through a pilot project, interest in DSRC with high utilization is increasing and antennas for roadside and on board equipment are being studied. A single patch was used for a vehicle antenna due to the requests of miniaturization of size, but there was performance degradation in most cases due to miniaturization. In addition, some methods to improve performance have been used in the antennas that were previously researched using the arrays, but they have the disadvantages of bulkiness in size of the antennas when using the arrays. Therefore, in this paper, the CPW fed microstrip patch antenna with the simple structure of being compact and easy to produce, which can be used in the OBU of DSRC, was designed.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.21 no.5
• /
• pp.33-39
• /
• 2021

In this study, we tried to find the correlation of the parameters and dual resonance of U-slot microstrip patch antenna with L-shaped Inset-feed structure and design broadband antenna using them. In the first step, we classified cases where dual resonance occurs through changes in antenna parameters that affect antenna performance. In the second step, we correlated each antenna parameter to the location and intensity of the resonance point, and 3 dB bandwidth. Next, antenna simulation confirmed the process of designing to have wide bandwidth using the correlation in the second step previously presented in the U-slot antenna case with narrow bandwidth. Finally, we fabricated a designed antenna and demonstrated the validity of antenna bandwidth broadening through the correlation analysis.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.5
• /
• pp.492-501
• /
• 2013

In this paper, a multi polarization reconfigurable microstrip antenna that can be used selectively for four polarizations(vertical polarization, horizontal polarization, right hand circular polarization, left hand circular polarization) at the S-band is presented. The proposed antenna consists of four PIN diodes and a microstrip patch with a cross slot and a circular slot and is fed by utiliting electromagnetic coupling between the microstrip patch and the feed line. The proposed antenna has a DC bias network to supply DC voltage to each PIN diode and the polarization can be determined by controlling the ON /OFF states of four PIN diodes. The fabricated antenna has a VSWR below 2 in the vertical polarization(3.17~3.21 GHz), the horizontal polarization(3.16~3.20 GHz), the left hand circular polarization (3.08~3.19 GHz), and the right hand circular polarization(3.10~3.2 GHz) frequency bands. The designed antenna has the cross polarization level higher than 20 dB, a gain over 5 dBi for the linear polarization states, and 3 dB axial ratio bandwidth wider than 50 MHz in the circular polarization states.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.3 s.357
• /
• pp.7-17
• /
• 2007

An analysis and design theory of an aperture-coupled cavity-fed back-to-back microstrip directional coupler is presented for the efficient and optimized design. For this purpose, an equivalent network is developed, and simple but accurate calculations of circuit element values are described. Design equations of the coupler are derived based on the equivalent circuit. In order to determine various structural design parameters, the evolutionary hybrid optimization method based on the genetic algorithm and Nelder-Mead method is invoked. As a validation check of the proposed theory and optimized design method, a 10 dB directional coupler was designed and fabricated. The measured coupling was 10.3 dB at 3 GHz, and the return loss and isolation were 31.8 dB and 30.5 dB, respectively. The directional coupler also showed very good quadrature phase characteristics. Good agreements between the measured and the design specifications fully validate the proposed network analysis and design procedure.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.39 no.5
• /
• pp.251-258
• /
• 2002

In this paper, the dipole-fed planar array antenna applied Yagi-Uda antenna away theory to microstrip antenna is designed and fabricated at X-band. The design procedure of the dipole-fed planar array antenna with the wide bandwidth is presented to be easily practiced to a wireless communication system. The radiation pattern, return loss and bandwidth of the antenna are improved by the finite differential time domain(FDTD) numerical method. The propriety of analysis of planar dipole antenna is proved from the measured data. From the measured results, the antenna maximum gain is 4.9dBi at center frequency of 10GHz and frequency bandwidth is about 40%. Front-to-back ratio is 16dB, and half-power beam-width of E-plane and H-plane are 117$^{\circ}$and 156$^{\circ}$, respectively. When VSWR of antenna is less than 2, the measured results are agreed well with the theoretical values in the frequency range from 7.4GHz to 11.88GHz.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.2
• /
• pp.495-504
• /
• 1996

In this paper, series-fed mirostrip array anteenas with coupling-slots are prposed and their operating characteristics are analyzed based on analyzed based on analytical and experimental results. An accurate analysis method for the slot-coupled feed structure is based on using both circuit coupling between anteenas and full-wave analysis which use travling wave mode and non-traveling wave mode on feed line. The basis functions that used for the numerical analysis bas been determined depending upon the accuracy, convergence properties of the solution, and the computation time:The patch uses 3 EB mode, the slot uses 1PWS mode, and feeders use 5 PWS mode. Series-fed array antennas have been designed, built, and tested in a standing-wave configuration. Using the results of the full-wave analysis, the chebyshev array antennas consisting of 8 elements are designed and fabricated changing the amount excited to each array element by adjusting slot length and by the slot position relative to the feeder. Experiment results show that the series-fed array antenna designed by adjusting the slot position relative to the feeder is superior to that designed by slot length.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.22 no.11
• /
• pp.1518-1523
• /
• 2018

A method for designing a DDQYA fed by a CPW is proposed in this paper. The proposed CPW-fed DDQYA consists of two series-connected strip dipoles, a ground reflector, and a strip-pair director. Instead of the conventional microstrip feed line in which the signal line is located on the substrate opposite to the antenna, a CPW is used because CPW is located on the same side with the antenna, and so the fabrication is easy. The strip-pair director is composed of two horizontally-separated strips, and it is added above the second dipole to enhance the gain in the high frequency region. A prototype of the proposed CPW-fed DDQYA is fabricated on an FR4 substrate. The fabricated antenna has a frequency band of 1.66-3.38 GHz(68.3%) for a voltage standing wave ratio < 2, and measured gain ranges 5.0-7.3 dBi over a frequency band of 1.60-2.90 GHz.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.3
• /
• pp.2-11
• /
• 2001

The L-shaped strip is shown to be an attractive feed for the thick mierostrip antenna (thickness around 10% of the operating wavelength). The L-strip incorporated with the radiating patch introduces a capacitance suppressing some of the inductance introduced by the strip itself. In this paper, a wideband microstrip patch antenna fed by L-strip for the PCS ($1,750{\sim}1,850MHz$) and IMT-2000 ($1,920{\sim}2,170MHz$) broad-band is presented. A two-element array fed by L-strip is also proposed. Both the antennas have stable radiation patterns across the passband. The impedance bandwidth is over 31% (VSWR < 1.5, 615 MHz) of the center frequency. Moreover, both the antennas have about 7 dBi average gain.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.6
• /
• pp.661-668
• /
• 2012

In this paper, a dual-fed small ICS repeater antenna with high isolation is designed, fabricated, and measured. Bandwidth and gain are optimized by changing the stub lengths near main patch and power divider, and also by changing the size of parasitic patch. To improve the isolation characteristic of the antenna, a dual-feeding method is applied in designing the antenna. The fabricated antenna has a VSWR less than 2, a gain over 7 dBi, and an isolation between the donor and the server antennas less than -65 dB from 1,920~2,170 MHz for 3G mobile communication.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.05a
• /
• pp.61-62
• /
• 2013

In this paper, a design method for a compact broadband planar dipole antenna fed by a microstrip (MS) line is studied. The proposed broadband dipole is optimized for terrestrial digital television (DTV) receiving. The dipole is fed by an MS line with 75-ohm characteristic impedance on an FR4 substrate and its size is $90mm{\times}180mm$. The dipole is modified to half bow-tie type for size reduction. A simplified balun is adopted for the impedance matching between the MS line and coplanar strip which feeds the dipole. The optimized dipole antenna for DTV band (470-806 MHz) is fabricated on an FR4 substrate and tested experimentally to verify the results of this study.