• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.267-274
• /
• 2009

Breakup and spray formation of pressure-swirl liquid jets injected into a low-speed convective-flow are experimentally investigated. Effects of the cross-flows on the macroscopic and microscopic spray parameters are optically measured in terms of jet Weber number and liquid-to-gas momentum ratio. The liquid stream undergoes Rayleigh jet breakup at lower jet Weber numbers and a liquid sheet isn't formed because of the weak radial velocity in the swirl jet. At higher jet Weber numbers, the macroscopic spray parameter is a very weak function of the momentum ratio but the effect of the convection on the microscopic spray parameter is significant through the secondary breakup with increasing in the liquid-to-gas momentum ratio. The convective-flow promotes bag/plume breakup and the spray formation, and its effect is more distinct at higher momentum ratio.

• Composites Research
• /
• v.17 no.3
• /
• pp.1-7
• /
• 2004

In the vacuum assisted RTM (VARTM) process that has become the center of attention for manufacturing massive composite structures, a good evacuation of air in the fiber preform is recognized as the prime factor. The microvoids, or the dry spots, are formed as a result of improper gate/vent locations and the mold geometry. The non-uniform resin velocity at the flow front leads to the formation of microvoids in the fibers, whereas the air in the microvoids can migrate along with the resin flow during mold filling. The residual air in the internal voids of a composite structure may cause a degradation of the mechanical properties as well as the structural failure. In this study, a unified macro- and micro analysis methods were developed to investigate the formation and transport of air in resin during VARTM process. A numerical simulation program was developed to analyze the three-dimensional flow pattern as well as the macro- and microscopic distribution of air in a composite part fabricated by VARTM process.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.2D
• /
• pp.105-111
• /
• 2010

Operating speed is one of key elements in the design and operation of freeway. Few studies have been carried out macroscopically to find characteristics of free-flow speed (FFS) using small sample size and not considering the conditions of traffic volume and the effects of hour periods. As an attempt to find out the characteristics of FFS, this study microscopically analysed both the distributions of freeway FFS and percentile speeds according to traffic volume and daily hour periods using huge sample size. It was found out that speed distributions are changed and showed different behaviors under the conditions of traffic volumes(1-5 veh/30sec) and daily hour periods(0-5, 6-8, 9-11, 12-19, 20-23). V85(85th percentile speed) at morning, night, and midnight period decreases according to increase in traffic volume respectively, whereas V85 at day time does not show considerable differences. So the behaviors of V85 according to hour periods dramatically changed according to the increase in traffic volume.

• Proceedings of the KSME Conference
• /
• 2001.06c
• /
• pp.246-250
• /
• 2001

In resin transfer molding (RTM), resin is forced to flow through the fiber perform of inhomogeneous permeability. This inhomogeneity is responsible for the mismatch of resin velocity within and between the fiber tows. The capillary pressure of the fiber tows exacerbates the spatial variation of the resin velocity. The resulting microscopic perturbations of resin velocity at the flow front allow numerous air voids to form. In this study, a mathematical model was developed to predict the formation and migration of micro-voids during resin transfer molding. A transport equation was employed to account for the migration of voids between fiber tows. Incorporating the proposed model into a resin flow simulator, the volumetric content of micro-voids in the preform could be obtained during the simulation of resin impregnation.

• Korea-Australia Rheology Journal
• /
• v.21 no.4
• /
• pp.245-268
• /
• 2009

Recent developments in dilute polymer solution rheology are reviewed, and placed within the context of the general goals of predicting the complex flow of complex fluids. In particular, the interplay between the use of polymer kinetic theory and continuum mechanics to advance the microscopic and the macroscopic description, respectively, of dilute polymer solution rheology is delineated. The insight that can be gained into the origins of the high Weissenberg number problem through an analysis of the configurational changes undergone by a single molecule at various locations in the flow domain is discussed in the context of flow around a cylinder confined between flat plates. The significant role played by hydrodynamic interactions as the source of much of the richness of the observed rheological behaviour of dilute polymer solutions is highlighted, and the methods by which this phenomenon can be incorporated into a macroscopic description through the use of closure approximations and multi scale simulations is discussed.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.6 no.3
• /
• pp.57-66
• /
• 2007

Weaving is defined as the crossing of two or more traffic streams traveling in the same general direction along a significant length of highway without the aid of traffic control devices. Compared with other freeway sections, perturbation is easy to happen at weaving section. Because there are a lot of lane-changing maneuvers at the weaving section, traffic is subject to turbulence in excess of that normally presents on freeway basic section. This turbulence causes operational problems and its impact must be considered. The purpose of this paper is to perform a basic study on flow characteristics by lane, which can be achieved through analyzing breakdown phenomenon in the microscopic approach. The study made use of data derived from the aerial photography for the microscopic analysis. This research produced the 30-second interval data such as flows, speeds, and densities for the macroscopic analysis and derived the vehicular data to draw time-space diagram for the microscopic analysis. The paper analyzed the traffic characteristics using flows, speeds and densities variation and investigated the conditions of breakdown occurrence with the time-space diagrams. The breakdown phenomenon was identified at weaving section and the propagation from free flow to synchronized flow was observed in this study. In the future, the findings help develop the traffic operational algorithm to manage the traffic congestion under ubiquitous circumstance since the conditions of breakdown Phenomenon can be understood more.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.427-733
• /
• 2003

Adiabatic shear bands have been observed in the serrated chip during high strain rate metal cutting process of medium carbon steel and titanium alloy. The recent microscopic observations have shown that dynamic recrystallization occurs in the narrow adiabatic shear bands. However the conventional flow stress models such as the Zerilli-Armstrong model and the Johnson-Cook model, in general, do not predict the occurrence of dynamic recrystallization (DRX) in the shear bands and the thermal softening effects accompanied by DRX. In the present study, a strain hardening and thermal softening model is proposed to predict the adiabatic shear localized chip formation. The finite element analysis (FEA) with this proposed flow stress model shows that the temperature of the shear band during cutting process rises above 0.5T$\sub$m/. The simulation shows that temperature rises to initiate dynamic recrystallization, dynamic recrystallization lowers the flow stress, and that adiabatic shear localized band and the serrated chip are formed. FEA is also used to predict and compare chip formations of two flow stress models in orthogonal metal cutting with AISI 1045. The predictions of the FEA agreed well with the experimental measurements.

• Journal of ILASS-Korea
• /
• v.11 no.3
• /
• pp.168-175
• /
• 2006

The static pressure distribution and flow characteristics inside the high-pressure swirl spray were investigated by measuring the static pressure inside the spray and applying the computational fluid dynamics (CFD). The static pressure difference between inner and outer part of spray was measured at different axial locations and operating conditions using a piezo-resislive pressure transducer. To obtain the qualitative value of swirl motion at different operating conditions, the spray impact-pressure at the nozzle exit was measured using a piezo-electric pressure transducer, and the flow angle was measured using a microscopic imaging system. The flow characteristics inside the high pressure swirl spray was simulated by the 1-phase 3-dimensional CFD model. The effect of pressure alternations on spray development was discussed with macroscopic spray images and a mathematical liquid film model. The results showed that the static pressure drop is observed inside the swirl spray as a result of the dragged air motion and the centrifugal force of the air. The recirculation vortex inside the spray was also observed inside the swirl spray as a result of the adverse pressure gradient along the axial locations. The results of analytical liquid film model and macroscopic spray images showed that the static pressure structure is one of the main parameters affecting the swirl spray development.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.4
• /
• pp.354-361
• /
• 2008

The dielectric characteristics of low-k interlayer dielectric materials was fabricated by plasma enhanced chemical vapor deposition (PECVD). BTMSM precursor was evaporated and introduced with the flow rates from 16 sccm to 25 sccm by 1sccm step in the constant flow rate of 60 sccm $O_2$ in process chamber. Manufactured samples are analyzed components by measuring FT/IR absorption lines. Decomposition each Microscopic structures through two-dimensional correlation analysis about mechanisms for the formation of SiOCH in $SiOCH_3$, Si-O-Si and Si-$CH_3$ bonding group and analyzed correlation between the micro-structure of each group. It is a tendency that seems to be growing of Si-O-Ci(C) bonding group and narrowing of Si-O-$CH_3$ bonding group relative to the increasing flow-rate BTMSM. The order of changing sensitivity about changes of flow-rate in Si-O-Si(C) bonding group is cross link mode$(1050cm^{-1})$ $\rightarrow$ open link mode$(1100cm^{-1})\rightarrow$ cage link mode $(1140cm^{-1})$.

• 한국전산유체공학회:학술대회논문집
• /
• 2003.10a
• /
• pp.268-269
• /
• 2003

The Boltzmann kinetic equation is solved directly by means of the conservative splitting method. Underexpanded supersonic free jet flows with small Knudsen numbers are studied. In this numerical simulation features intrinsic to appropriate experiments are observed. Streamwise vortices in a mixing layer and chaotic downstream temporal-spatial fluctuations of microscopic quantities with large amplitude are obtained.