• 한국전산유체공학회:학술대회논문집
• /
• 2010.05a
• /
• pp.233-238
• /
• 2010

A two-dimensional laminar flow past a vertical plate in a microchannel is investigated. At far upstream and downstream from the plate in the microchannel, the plane Poiseuille flow exists. The Stokes flow for this microchannel is investigated analytically and then the laminar flow by numerical method. For the Stokes flow analysis, the method of eigenfunction expansion is used. From the results, the streamline pattern and the pressure distribution are plotted, and the additional pressure drop induced by the plate and the force exerted on the plate are calculated as functions of the length of the plate. For the laminar flow, finite difference method (FDM) is used to obtain the vorticity and the stream function. When the Reynolds number exceeds a critical value, a pair of viscous eddies appears behind the plate.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.1888-1893
• /
• 2007

In this study, the microchannel plated heat exchanger were numerically studied for the enhancement of heat transfer in the channel configuration. Unit cold and hot fluid region with the microchannel were modeled and periodic boundary condition at the side wall was applied to continuously repeating geometry. The material of micro-structured plate is STS304 and working fluid is water. Triangular obstacles were placed in micro channel to enhance heat transfer. The performance of microchannel plated heat exchangers were numerically investigated with various obstacle configuration and Reynolds number under the parallel and counter flows. Heat transfer rate has increased about 18% compared with straight channel, but pressure drop also increased about 3.5 times. The main factor of increasing of pressure drop and heat transfer rate is considered that the momentum was lost to collide against obstacles, generation of secondary flow and boundary layer separation, wake and vortex forming phenomena.

• Proceedings of the SAREK Conference
• /
• 2007.11a
• /
• pp.229-234
• /
• 2007

Microscale heat transfer and microfluidics have become increasingly important to overcome some very complex engineering challenges. The use of very small passages to gain heat transfer enhancement is a well documented method for achieving high heat flux dissipation. As the passage size is decreased, the heat transfer performance increases but the pressure drop increases sharply when the passage size is reduced. In this study, the performance evaluation of micro plated heat exchangers under the counter flows with straight, V-shaped and Y-shaped channel are carried out.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.11
• /
• pp.1119-1126
• /
• 2011

In conventional microchannel heat exchangers, only one kind of fluid (hot or cold) flows in each plate. The channels contain different kinds of fluid depending on the vertical position, but they have the same kind of fluid at all horizontal positions. Therefore, there is a slower heat transfer rate in the horizontal direction than in the vertical direction. We propose a microchannel heat exchanger in which hot and cold fluid flows alternately in each plate to improve the thermal performance. This novel channel array requires a special design for the inlet and outlet. The proposed channel array has a faster heat transfer rate than a conventional channel array. The thermal performance of the novel channel array increases with increasing Reynolds number and Prandtl number, but it decreases as the ratio of solid to fluid thermal conductivity increases.

• Proceedings of the SAREK Conference
• /
• 2004.06a
• /
• pp.16-16
• /
• 2004

• Journal of Astronomy and Space Sciences
• /
• v.19 no.1
• /
• pp.57-66
• /
• 2002

We designed two-dimensional position sensitive MCP(mixt.ochannel plate) detector for FIMS, which is composed of MCP, delay line anode, and delay line readout elec-tronics. And also, we fabricated and tested for the operation stability and resolution of the delay line readout electronic system. An anode simulator and a stimulator were used instead of the real MCP and anode during the test to see the electronic contribution to the resolution. The readout electronics was operated stably and showed time resolution of about 560 ps for the spectral direction and about 100 ps for the image direction respectively.

• Journal of Astronomy and Space Sciences
• /
• v.18 no.2
• /
• pp.145-152
• /
• 2001

For the research of solar EUV (extreme ultraviolet) radiation, we have designed a small-sifted engineering model of solar EUV telescope, which is suitable for a Korean satellite. The EUV sole. telescope was designed to observe the sun at $584.3AA$(He I) and $629.7AA$(OV) The optical system is an f/8 Ritchey-Chr rien, and the effective diameter and focal length are 80mm and 640mm, respectively. The He I and 0V filters are loaded in a filter wheel. In the detection part, the MCP (Microchannel Plate) type is Z-stack, and the channel-to-diameter radio is 40:1. MCP and CCD are connected by fiber optic taper. A commercial optical design software is used for the analysis of the optical system design.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.3
• /
• pp.272-281
• /
• 2007

A numerical simulation on nitrogen gas flow in a long parallel plate microchannel was performed to obtain the effect of compressibility and rarefaction on gaseous flow in microchannels. The simulation was based on steady. two dimensional compressible Navier-Stokes and energy equations with noslip and first order slip boundary conditions. The channel was $1.2{\mu}m$ deep and $3000{\mu}m$ long. The Reynolds numbers were in the range of order from $10^{-2}$ to $10^{-1}$. So the flow was assumed to be laminar. The computations were performed on various pressure ratios. The outlet pressure was fixed to atmospheric pressure. The outlet Knudsen number was 0.0585, consequently the flow was in the slip flow regime. The computations were performed with the assumption of isothermal channel walls. The results were compared with the experimental data. The agreement was good.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.1
• /
• pp.137-141
• /
• 2008

Biochip, which implements bioanalytical process on a tiny surface, is one of candidates for medical diagnosis, drug screening, and molecular sensing. In general, a type of biochip based on microfluidics is composed of microcomponents including microchannel, pump, and valve, which require complicated processes. In this study, gray-scale photolithography(GSPL) was applied to fabricate a biochip with multiple layers. A mould for casting PDMS(polydimethylsiloxane) channel, was fabricated using GSPL. A gray-photomask was prepared by printing gray patterns on a high-quality glossy paper followed by photoreducing by 10:1 onto the photo-film. The formation of multiple layers was studied according to the change of gray level of pattern and the developing time. A biochip composed of a weir(multiple layer structure) and a reaction chamber in a single microchannel was fabricated in a glass plate. Finally, we investigated the application of biochip to antigen-antibody reaction by packing the microbead coated with antibody.

• 유체기계공업학회:학술대회논문집
• /
• 2006.08a
• /
• pp.179-183
• /
• 2006

Surface roughness is present in most of the microfluidic devices due to the microfabrication techniques. This paper presents lattice Boltzmann method (LBM) results for laminar flow in a microchannel with surface roughness. The surface roughness is modeled by an array of rectangular modules placed on top and bottom side of a parallel-plate channel. In this study, LBGK D2Q9 code in lattice Boltzmann Method is used to simulate flow field for low Reynolds number in a micro-channel. The effects of relative surface roughness, roughness distribution, roughness size and the results are presented in the form of the product of friction factor and Reynolds number. Finally, a significant increase in Poiseuille number is detected as the surface roughness is considered, while the effect of roughness on the microflow field depends on the surface roughness.