• Proceedings of the KIEE Conference
• /
• 1998.07c
• /
• pp.1235-1237
• /
• 1998

Spacer Dampers must be carefully designed and tested. Because it can protect conductors from conductor oscillations due to winds and electrical forces. If the spacer damper has any problems in itself, it may cause extensive damage to the transmission lines. This paper suggests a design method and considerations of spacer damper for bundled conductor transmission lines.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2016.05a
• /
• pp.505-508
• /
• 2016

In city, tracing of power transmission lines is difficult due to compound installation of overhead and underground lines, transposition, bad view caused by trees or big buildings. It is hard problem for electrical technician on site to trace power transformers or power lines to serve customers in 3 phase -4 wires power distribution systems. It is necessary that the correct and fast tracing method is required for load balancing among distribution lines. Old technology use to trace lines with high power impulse injection. Our proposed method uses to trace lines with very small power high frequency signal injection. Simulation models for 3-phase power transformers, 3-phase wire lines, and customer loads are described to investigate the transmission characteristics of high frequency power line carrier. Distribution lines have only a limited ability to carry higher frequencies. Typically power transformers in the distribution system prevent propagating the higher frequency carrier signal. The proposed method uses the limited propagation ability to identify the power transformer to serve customers. The system consists of a transmitter and a receiver with power-line communication module. Some experiments are conducted to verify the theoretical concepts in a big commercial building. Also some simulations are done to help and understand the concepts by using MATLAB Simulink simulator.

• The KIPS Transactions:PartB
• /
• v.14B no.6
• /
• pp.453-460
• /
• 2007

In this paper, we present a method to extract the text lines in poorly structured documents. The text lines may have different orientations, considerably curved shapes, and there are possibly a few wide inter-word gaps in a text line. Those text lines can be found in posters, blocks of addresses, artistic documents. Our method based on the traditional perceptual grouping but we develop novel solutions to overcome the problems of insufficient seed points and vaned orientations un a single line. In this paper, we assume that text lines contained tone connected components, in which each connected components is a set of black pixels within a letter, or some touched letters. In our scheme, the connected components closer than an iteratively incremented threshold will make together a chain. Elongate chains are identified as the seed chains of lines. Then the seed chains are extended to the left and the right regarding the local orientations. The local orientations will be reevaluated at each side of the chains when it is extended. By this process, all text lines are finally constructed. The proposed method is good for extraction of the considerably curved text lines from logos and slogans in our experiment; 98% and 94% for the straight-line extraction and the curved-line extraction, respectively.

• Journal of Power Electronics
• /
• v.13 no.4
• /
• pp.701-711
• /
• 2013

This paper takes into account the influence of the different impedances of distribution lines on power distribution among inverters when the inverters are paralleled with the droop control method. The impact of distribution lines on the power distribution of inverters can be divided into two aspects. Firstly, since the distributed generators are in low voltage grids, there is resistive impedance in the distribution lines, which will cause control coupling and reduce system stability. The virtual negative resistive impedance of inverters is adopted in this paper to neutralize the resistive element of distribution lines and thus make the distribution line impedance purely inductive. Secondly, after solving the resistive impedance problem, the difference in the inductive impedance value of distribution lines due to the low density of distributed generators will cause an unequal share of reactive power. With regards to this problem, modification is put forward for the droop control strategy to share the reactive power equally. The feasibility of the design is validated by simulation and experimental results.

• Journal of the Korean Society of Tobacco Science
• /
• v.27 no.1 s.53
• /
• pp.11-18
• /
• 2005

The nicotine converter genotypes of burley tobacco (Nicotiana tabacum L.), which convert nicotine to nornicotine, contain a high amount of nornicotine that degrades tobacco quality and smoking taste. Elimination of nicotine converter plants before seed harvesting is required for breeding nicotine low-converter lines and for increasing their seed production. This study aims to develop a rapid and convenient method of identifying nicotine converter plants of burley breeding lines of KB9118(KB108) using thin-layer chromatography (TLC) and isatin coloration method. Out of 223 plants in 10 lines harvested at maturity in 2002, 102 plants ($45\%$) were identified as nicotine converters by TLC of tobacco leaves air-cured. For 16 lines selected as low-converters in 2002, 148 plants grown in the field in 2003 were tested by the isatin coloration method using two detached leaves at the flowering stage thoroughly sprayed with $1\%\;NaHCO_3$ solution and cured in conditioned chambers for the early identification of nicotine to nornicotine conversion. From these samples, 46 plants ($31\%$) in 4 lines were identified as nicotine converters, indicating that the ratio of converters significantly decreased by one time selection. Mean percent conversion of non-screened lines was $14\%$ higher than that of following generation. Therefore in the burley tobacco, a rapid and convenient means of identifying and removing nornicotine converter plants by the isatin coloration method during growth in the greenhouse or field were effective in reducing the converter plants in the following generation.

• Journal of Computational Design and Engineering
• /
• v.2 no.2
• /
• pp.79-87
• /
• 2015

Surface segmentation and edge feature lines extraction from fractured fragments of relics are essential steps for computer assisted restoration of fragmented relics. As these fragments were heavily eroded, it is a challenging work to segment surface and extract edge feature lines. This paper presents a novel method to segment surface and extract edge feature lines from triangular meshes of irregular fractured fragments. Firstly, a rough surface segmentation is accomplished by using a clustering algorithm based on the vertex normal vector. Secondly, in order to differentiate between original and fracture faces, a novel integral invariant is introduced to compute the surface roughness. Thirdly, an accurate surface segmentation is implemented by merging faces based on face normal vector and roughness. Finally, edge feature lines are extracted based on the surface segmentation. Some experiments are made and analyzed, and the results show that our method can achieve surface segmentation and edge extraction effectively.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.3C no.4
• /
• pp.117-122
• /
• 2003

The AC power lines and signal lines of info-communication networks are routed on overhead poles and are highly exposed to lightning strikes. Due to the potential difference between grounding points of AC power lines and signal lines, the electronic equipments connected to the signal lines can easily be damaged by lightning surges. In this work, in order to develop reliable methods of protecting information and communication facilities from lightning surges, the reliability and performance of SPDs (surge protective devices) were experimentally investigated in an actual-sized test circuit. The behaviors of SPDs against lightning surges from AC power lines and signal lines and the coordinated effects of SPD installation methods were evaluated. As a consequence, it was confirmed that the bypass arrester methods and common grounding system are both highly effective.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.16 no.5
• /
• pp.90-96
• /
• 2002

The AC power lines and signal lines of info-communication networks are muted on overhead poles and are exposed to lightning strikes. Due to the potential difference between groundings of the AC power lines and telecommunication lines, the electronic equipments connected to the telecommunication lines can easily be damaged by lightning surges. In this work, in order to develop the reliable ways to protect information and communication facilities from lightning surges, the reliability and performance of surge protective devices were experimentally investigated in actual-sized test circuit. The operation behaviors of surge protective devices against lightning surges from the AC power lines and telecommunication lines and the coordination effects of SPD installation method were evaluated. As a consequence, it was confirmed that the bypass arrester and common grounding system is very effective.

• Journal of Crop Science and Biotechnology
• /
• v.11 no.1
• /
• pp.63-68
• /
• 2008

The induced genetic divergence was estimated in 44 mutant lines of finger millet variety GPU 26, developed by single and combination treatments with gamma rays, EMS and NG using three multivariate analyses. The mutant lines were grouped into eight genetically diverse clusters by multivariate D2 and canonical analyses and 11 clusters by dendrogram grouping through Gower's similarity coefficient. The clustering pattern in these three methods was almost similar. Twelve mutant lines in D2 and 13 in the dendrogram grouping method were grouped in the parental cluster(Cluster I) indicating that they did not possess enough divergence from the parent to be classified as micromutant lines. However a large proportion of mutant lines showed divergence from the parent variety and also among themselves. No definite relationship of mutagenic origin and clustering of mutant lines were observed. The mutant lines developed from the same mutagenic treatments often grouped into different clusters indicating that each mutagenic treatment was effective in inducing diverse types of changes in the nine traits studied. The hybridization program between the divergent mutant lines GE 2-2 or GE 3-4 with GG 3-1 is expected to give promising and desirable segregants in subsequent generations. Traits such as days to 50% flowering and days to maturity had major contributions to the induced genetic divergence.

• Journal of the Korean Society of Safety
• /
• v.5 no.3
• /
• pp.44-50
• /
• 1990

This study is conducted to examine the theoretical background of characteristics for electric shock encountered in special high-voltage electric lines among the accidents of electric shock, and to calculate applied current to human body and field strength over the head by means of numerical anaysis through FEM(Finite Element Method), and to make clear the hazard level to the human body, and to establish the approach limit distance of human body to the electric lines, which could be applied to the safety standard while working in the vicinity of special high-voltage electric lines.