• Steel and Composite Structures
• /
• 제51권5호
• /
• pp.563-573
• /
• 2024

This research experimentally evaluated the local stress distribution along the cross-section of composite beams under both positive and negative moments. The experiment utilized a large-scale, two-story, two-by-three bay steel gravity frame with a concrete on metal deck floor system. The composite shear connections, which are nominally assumed to be pinned under gravity loading, can develop non-negligible moment-resisting capacity when subjected to lateral loads. This paper discusses the local stress distribution, orshear lag effects, observed near the beam-to-column connections when subjected to combined gravity and lateral loading. Strain gauges were used for measurements along the beam depth at varying distances from the connection. The experimental data showed amplified shear lag effects near the unconnected region of the beam web and bottom flange under the applied loading conditions. These results indicate that strain does not vary linearly across the beam cross-section adjacent to the connection components. This insight has implications for the use of experimental strain gauge data in estimating beam demands near the connections. These findings can be beneficial in informing instrumentation plans for future experimental studies on composite beams.

• 대한치과보철학회지
• /
• 제38권2호
• /
• pp.200-213
• /
• 2000

Lasers have given dentistry a new rapid, economic, and accurate technique for metal joining. Although laser welding has been recommended as an accurate technique, there are some limitations with this technique. For example, the two joining surfaces must have a tight-fitting contact, which may be difficult to achieve in some situations. The tensile samples used for this study were made from a custom-made pure titanium and type III gold alloy plates. 27 of 33 specimens were sectioned perpendicular to their long axis with a carborundum disk and water coolant. Six specimens remained and served as the control group. A group of 6 specimens was posed as butt joints in custom parallel positioning device with a feeler gauge at each of three gaps : 0.00, 0.25. and 0.50mm. All specimens were then machined to produce a uniform cross-sectional dimension, none of the specimens was subjected to any subsequent form of heat treatment. Scanning electron microscopy was performed on representative tested specimens at fractured surfaces in both the parent metal and the weld. Vickers hardness was measured at the center of the welds with a micropenetrometer using a force of 300gm for 15 seconds. Measurement was made at approximately $200{\mu}m\;and\;500{\mu}m$ deep from each surface. One-way analysis of variance (ANOVA) and Scheffe's test was calculated to detect differences between groups. The purpose of this study is to compare the strength and properties of the joint achieved at various butt Joint gaps by the laser welding of type III gold alloy and pure titanium tensile specimens in an argon atmosphere. The results of this study were as follows : 1. When indexing and welding pure titanium, there was no decrease in ultimate tensile strength as compared with the unsectioned alloys for indexing gaps of 0.00 to 0.50mm, although with increasing gap size may come increased distortion (p>0.05). 2. When indexing and welding type III gold alloy, there were significant differences in ultimate tensile strength among groups with weld gaps of 0.00mm, 0.25 and 0.50mm, and the control group. Group with butt contact without weld gap demonstrated a significant higher ultimate tensile strength than groups with weld gaps of 0.25 and 0.50mm (p<0.05). 3. When indexing and welding the different metal combination of type III gold alloy and pure titanium, there were significant differences in ultimate tensile strength between groups with weld gaps of 0.00, 0.25, and 0.50mm. However, the mechanical properties of the welded joint would become too brittle to be acceptable clinically (p<0.05). 4. The presence of large pores in the laser welded joint appears to be the most important factor in controlling the tensile strength of the weld in both pure titanium and type III gold alloy.

• 대한약리학회지
• /
• 제21권1호
• /
• pp.62-77
• /
• 1985

Hydroxyl raical$(OH{\cdot})$을 생성하는 것으로 알려진 iron-catalyzed Haber-Weiss rocation에서 superoxide anion $(O^{-}_{2}{\cdot})$은 주로 $Fe^{+++}$을 $Fe^{++}$로 환원시키는 데에 작용하는 것으로 추정하고 있다. 이러한 $OH{\cdot}$ 의 역할은 다른 환원제들에 의하여 대체가 가능할 것으로 추측되며 생물계의 환원제의 하나로써 ascorbate가 관심의 대상이 되고 있다. 이에 따라 본 연구에서는 $Fe^{++}$와 $H_2O_2$ 존재하에서 $OH{\cdot}$ 을 생성하는 ascorbate 의 역할을 hyaluronic acid의 변성과 methional로 부터 ethylene 생성에 대한 효과로써 관찰하였다. Ascorbate는 $Fe^{++}$와 $H_2O_2$에 의한 hyaluronic acid의 변성을 촉진하였으며, 이런 현상은 점성도 변화와 Sepharose 4B를 이용한 코로마토그라피에 의하여 확인할 수 있었다. 이때 관찰되는 변성은 catalase와 $OH{\cdot}$ scavenger에 의하여 거의 완전히 억제 되었다. 또한 ascorbate는 $Fe^{++}$와 $H_2O_2$에 의한 methional로 부터 ethylene생성을 항진시킴으로써 상기의 결과를 뒷받침 하였다. 다른 환원제들(cysteine, glutathione, NADH와 NADH와 NAKPH)도 ascorbate와 같이 hyaluronic acid의 변성과 methional로 부터 ethylene생성을 촉진하였으나, 그들의 산화형인 NAD와 NADP의 효과는 관찰 할 수 없었다. 그러므로 $OH{\cdot}$ 생성에 있어 철이온의 환원이 관여함을 시사하였다. 또한 metal ion가운데 $Fe^{++}$는 $OH{\cdot}$ 생성에 가장 강력한 촉매작용을 나타내었다. 이상의 결과는 ascorbate가 $(OH{\cdot})$ 을 생성하는 metal-catalyzed reaction에서 $Fe^{+++}$을 $Fe^{++}$로 환원하는 $O^{-}_{2}{\cdot}$의 작용을 대신할 수 있음을 증명하며 이와같은 ascorbate 의존적인 $OH{\cdot}$ 의 생성은 ascorbate가 조직손상에 관여할 가능성을 시사하였다.

• 한국강구조학회 논문집
• /
• 제16권3호통권70호
• /
• pp.387-396
• /
• 2004

본 연구에서는 강교량의 강상판에서 많이 사용되는 U리브 현장이음부에 대해 시공오차로 인한 단차의 영향을 조사하기 위해 실물 대모형에 대해 응력해석을 실시하였다. 또한 실물대모형 시험체를 제작하여 3점 휨 피로실험을 실시하였으며, 주사형전자현미경(SEM) 및 비치마크를 이용하여 피로균열 발생점 및 피로균열전파방향을 조사하였다. 실물대모형 모델에 대한 응력해석 결과, U리브의 하면 우각부에 응력이 크게 나타났으며, 단차가 커질수록 응력이 현저히 증가하는 것을 확인할 수 있었다. 실물대모형 시험체에 대한 정하중 및 피로실험에서도 U리브 하면의 우각부에 응력이 크게 나타났으며, 단차가 크면 피로수명은 단축되고 단차가 적으면 피로수명은 길어졌다. 또한 파단면 조사결과, 피로균열은 모재측 루트부에서 발생하여 용접비드 표면측으로 전파되었다.

• 한국융합학회논문지
• /
• 제9권8호
• /
• pp.179-184
• /
• 2018

자동차의 구동방식은 전륜구동, 후륜구동, 4륜구동의 방식이 있다. 구동방식에서 운전자가 원하는 방향으로 전환하는 것과 바퀴에 동력을 전달하여 구동하는 두 가지의 역할을 수행하는데 있어 가장 중요한 부품이 등속 조인트이다. 도로상에서 주행 시에는 노면의 상태에 따라서 동력을 전달하는 부품들에 충격이 가해질 수 있다. 본 연구에서는 각각 샤프트의 길이가 다른 3개의 등속 조인트 각 모델들은 CATIA로 모델링하였고 ANSYS를 이용하여 구조 및 피로해석을 수행하였다. 본 연구 결과로는 Model 2가 다른 모델 대비 뛰어난 내구성을 가짐을 알 수 있었다. 이러한 결과를 이용하여 충격에 대한 내구성을 가지는 등속 조인트 설계를 할 때에 유용한 자료가 될 것이라고 사료되며, 등속 조인트의 디자인을 융합기술에 접목하여 미적 감각을 나타낼 수 있다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1845-1848
• /
• 2005

The automatic $CO_2$ welding is a manufacturing process to produce high quality joints for metal and it could provide a capability of full automation to enhance productivity. Despite the widespread use in the various manufacturing industries, the full automation of the robotic $CO_2$ welding has not yet been achieved partly because the mathematical model for the process parameters of a given welding task is not fully understood and quantified. Several mathematical models to control welding quality, productivity, microstructure and weld properties in arc welding processes have been studied. However, it is not an easy task to apply them to the various practical situations because the relationship between the process parameters and the bead geometry is non-linear and also they are usually dependent on the specific experimental results. Practically, it is difficult, but important to know how to establish a mathematical model that can predict the result of the actual welding process and how to select the optimum welding condition under a certain constraint. In this research, an attempt has been made to develop an intelligent algorithm to predict the weld geometry (top-bead width, top-bead height, back-bead width and back-bead height) as a function of key process parameters in the robotic $CO_2$welding. A sensitivity analysis has been conducted and compared the relative impact of three process parameters on bead geometry in order to verify the measurement errors on the values of the uncertainty in estimated parameters.

• 한국공작기계학회논문집
• /
• 제16권2호
• /
• pp.14-22
• /
• 2007

In this paper, the acoustic emission(AE) behaviors were investigated with single-and 2-spot resistance spot welded SPCC specimens. Test specimens were welded horizontally and/or vertically according to the rolling direction of base netal in 2-spot welding. In the case of 2-spot welding, when tensile-shear test has below amplitudes: crack initiation $50{\sim}60dB;$ tear fracture $40{\sim}50dB$. And when cross tensile test has below amplitudes: early stage $75{\sim}85dB;$ yielding point $65{\sim}75dB;$ post yielding $40{\sim}60dB;$ plug fracture $70{\sim}80dB\;or\;90{\sim}100dB$. Also, from the b-value that is slope of AE amplitude, we knew that there are lots of low amplitudes if b-value is big(i.e., tensile-shear $specimen{\rightarrow}tear$ fracture or shear fracture), and there are lots of high amplitudes if b-value is small(i.e.. cross tensile $specimen{\rightarrow}plug$ fracture). As the results of fiacture mechanism analyses through AE amplitude distributions, change of the b-value represented fracture patterns of materials. Correspondingly, low amplitude signals appeared in crack initiation, and high amplitude signals appeared in base metal fracture. We confirmed that these amplitude distributions represented the change or degradation of materials.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.596-599
• /
• 2004

The robotic $CO_2$ welding is a manufacturing process to produce high quality joints for metal and it could provide a capability of full automation to enhance productivity. Despite the widespread use in the various manufacturing industries, the full automation of the robotic $CO_2$ welding has not yet been achieved partly because the mathematical model for the process parameters of a given welding task is not fully understood and quantified. Several mathematical models to control welding quality, productivity, microstructure and weld properties in arc welding processes have been studied. However, it is not an easy task to apply them to the various practical situations because the relationship between the process parameters and the bead geometry is non-linear and also they are usually dependent on the specific experimental results. Practically, it is difficult, but important to know how to establish a mathematical model that can predict the result of the actual welding process and how to select the optimum welding condition under a certain constraint. In this research, an attempt has been made to develop an intelligent algorithm to predict the weld geometry (top-bead width, top-bead height, back-bead width and back-bead height) as a function of key process parameters in the robotic $CO_2$welding. To achieve this above objective, Taguchi method was employed using five different process parameters (tip gap, gas flow rate, welding speed, arc current, welding voltage) as a guide for optimization of process parameters.

• Journal of Welding and Joining
• /
• 제33권6호
• /
• pp.6-12
• /
• 2015

Thermal fatigue life of the automobile exhaust manifold is directly affected by the restraint force according to the structure of exhaust system and bead shape of the welded joints. In the present study, the microstructural changes and precipitation behavior during thermal fatigue cycle of the 18wt% Cr ferritic stainless steel weld heat affected zone (HAZ) considering restraint stress were investigated. The simulation of weld HAZ and thermal fatigue test were carried out using a metal thermal cycle simulator under complete constraint force in the static jig. The change of the restraint stress on the weld HAZ was simulated by changing the shape of notch in the specimen considering the stress concentration factor. Thermal fatigue properties of the weld HAZ were deteriorated during cyclic heating and cooling in the temperature range of $200^{\circ}C$ to $900^{\circ}C$ due to the decrease of Nb content in solid solution and coarsening of MX type precipitates, laves phase, $M_6C$ with coarsening of grain and softening of the matrix. As the restraint stress on the specimen increased, the thermal fatigue life was decreased by dynamic precipitation and rapid coarsening of the precipitates.

• Journal of Acupuncture Research
• /
• 제21권5호
• /
• pp.249-256
• /
• 2004

Objectives : Wilson's disease is an autosomal recessive abnormality in the hepatic excretion of copper that results in toxic accumulation of the metal in liver, brain, and other organs. The purpose of this case study is to show a case with Wilson's disease treated with acupuncture therapy. Methods : We experienced a 17 year old male patient with a Wilson's disease whose main symptoms are neurological symptoms, such as spasticity, quadripleia and dysphagia. The patient was treated with acupuncture therapy for 3 weeks. Results : Spasticity was assessed by the modified Ashworth scale in an every week. 1. Lt. elbow, wrist and ankle joint improved Gr.III to Gr.II. 2. Rt. each joints and Lt. knee joint seemed to improve a little but no grade changed. Conclusions : This study is just one case and the period of acupuncture therapy is short, which make this case study less sufficient to decide the effect of acupuncture therapy. However, in this case study, acupuncture therapy seems somewhat effective to neurological symptoms of Wilson's disease, such as spasticity and quadriplegia. We suggest that oriental medicine should be studied to cure Wilson's disease from now on.