• 전력전자학회논문지
• /
• 제23권3호
• /
• pp.199-207
• /
• 2018

In this paper, an all-metal domestic induction heating (IH) system that can quickly identify ferromagnetic and non-ferromagnetic pots considering temperature changes in the working coil is designed. Load modeling is performed after analyzing the parameters of the pot material and the central misalignment of the working coil. To improve the performance and stability of the all-metal IH cooking heater, a power curve-fitting model is used to design a control system that quickly responds to load parameter fluctuations. In addition, a power control algorithm is established to compensate for the reference value by reflecting the increase in working coil temperature during heating of the non-ferromagnetic pot. The validity of the proposed control algorithm for the all-metal IH is verified by experiments using a 3.2 kW all-metal IH cooking heater.

• 대한전자공학회논문지SD
• /
• 제41권7호
• /
• pp.37-41
• /
• 2004

We have formulated an empirical analytic model for the static characteristics of implanted vertical-cavity surface-emitting lasers (VCSELs). Specifically, we have derived analytic formulas for the threshold current, slope efficiency, dynamic resistance, and the output power and forward voltage at the operation current of 12 ㎃ in terms of the implant and metal-aperture radii by fitting the measured results. The radii of the metal aperture and implant mask of the 850 nm VCSELs range from 4 to 12.5 ${\mu}{\textrm}{m}$ and 7 to 17.5 ${\mu}{\textrm}{m}$ respectively. The model shows the way of tailoring the VCSEL characteristics by changing the mask dimensions only.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1996년도 추계학술대회 논문
• /
• pp.180-186
• /
• 1996

Using carbon steel or ceramic as a shaft material of monolithic and slited insert ring clamped on it. The fitting strengths of the sgrink fitted assemblies measured from room temperature to 30$0^{\circ}C$ and following conclusions were obtained as results of this investigation. 1) The fitting condition under which the shrink fitted assemble was stronger than that using simple fit in high temperature. 2) When both material of the 30mm-diameter shaft and 55mm-diameter boss are SM45C the clamping torque is increased 2.7times as the interference increases 3 times from 20${\mu}{\textrm}{m}$ at the contact length of 6mm monolithic fit. 3) When only the material of boss is changed to STS 304 the clamping torque is increased at the rate of 37.3N.m per 1mm increase of the contact length at the interference of 50${\mu}{\textrm}{m}$ monolithic fit.

• 한국지하수토양환경학회지:지하수토양환경
• /
• 제22권5호
• /
• pp.128-134
• /
• 2017

This work presents the adsorption capability of green tea and ginseng leaves to adsorb heavy metals such as Cd(II), Cu(II), and Pb(II) in aqueous solution. FT-IR analysis indicates the presence of oxygen containing functional groups (carboxyl groups) in two kinds of leaves. High pH condition was favorable to the adsorption of heavy metal ions due to the enhanced electrostatic attraction and the precipitation reaction of metal ions. The adsorption of Cd(II), Cu(II), and Pb(II) reached equilibrium within 10 min, achieving high removal efficiencies of 80.3-97.5%. The adsorption kinetics data of heavy metal ions were fitted well with the pseudo-second-order kinetic model. The maximum adsorption amounts of Cd(II), Cu(II), and Pb(II) ions were 8, 3.5, and 15 mg/g, respectively, in the initial concentration range from 0.15 to 0.75 mM. Based on the fitting data obtained from isotherm models, heavy metal adsorption by green tea and ginseng leaves could occur via multi-layer sorption.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 추계학술발표대회 논문집
• /
• pp.60-63
• /
• 2002

Metal/intermetallic laminated composites have been manufactured by SHS reactions between Ni and Al elemental metal foils. Microstructure showed that the intermetallic volume fraction was 55%, 45%, 35% in the 1:1, 2:1, 4:1 thickness ratio(Ni:Al) specimen and the main phases of the intermetallic were transformed from $Ni_2Al_3$ to NiAl when the thickness ratio was increased. Tensile strength and elongation were increased when the volume fraction of Ni metallic phase was increased. Under assumptions of isostrain condition, the tensile strength of metal/intermetallic laminated composites didn't obey the ROM due to the thermal residual stress and this was confirmed by X-ray residual stress analysis. Fracture toughness results by the SENB test showed R-curves with upward curvature based on LSB condition. Bridging stress based on LSB condition was determined by the curve fitting analysis, In-situ observed microstructure during fracture test showed that the various bridging mechanism such as crack bridging, crack branching and ductile failure of metallic layer were occurred

• 한국수소및신에너지학회논문집
• /
• 제27권2호
• /
• pp.176-181
• /
• 2016

Recent years, supercapacitors have been attracting a growing attention as an efficient energy storage, due to their long-lifetime, device reliability, simple device structure and operation mechanism and, most importantly, high power density. Along with the increasing interest in flexible/stretchable electronics, the supercapacitors with compatible mechanical properties have been also required. A eutectic gallium-indium (EGaIn) liquid metal could be a strong candidate as a soft electrode material of the supercapacitors because of its insulating surface oxide layer for electric double layer formation. Here, we report the electrochemical study on the charging/reaction process at the interface of EGaIn liquid metal and electrolyte. Numerical fitting of the charging current curves provides the capacitance of EGaIn/insulating layer/electrolyte (${\sim}38F/m^2$). This value is two orders of magnitude higher than a capacitance of a general metal electrode/electrolyte interface.

• 산업경영시스템학회지
• /
• 제46권3호
• /
• pp.139-147
• /
• 2023

The metal bush assembling process is a process of inserting and compressing a metal bush that serves to reduce the occurrence of noise and stable compression in the rotating section. In the metal bush assembly process, the head diameter defect and placement defect of the metal bush occur due to metal bush omission, non-pressing, and poor press-fitting. Among these causes of defects, it is intended to prevent defects due to omission of the metal bush by using signals from sensors attached to the facility. In particular, a metal bush omission is predicted through various data mining techniques using left load cell value, right load cell value, current, and voltage as independent variables. In the case of metal bush omission defect, it is difficult to get defect data, resulting in data imbalance. Data imbalance refers to a case where there is a large difference in the number of data belonging to each class, which can be a problem when performing classification prediction. In order to solve the problem caused by data imbalance, oversampling and composite sampling techniques were applied in this study. In addition, simulated annealing was applied for optimization of parameters related to sampling and hyper-parameters of data mining techniques used for bush omission prediction. In this study, the metal bush omission was predicted using the actual data of M manufacturing company, and the classification performance was examined. All applied techniques showed excellent results, and in particular, the proposed methods, the method of mixing Random Forest and SA, and the method of mixing MLP and SA, showed better results.

• Bulletin of the Korean Chemical Society
• /
• 제7권1호
• /
• pp.29-35
• /
• 1986

An empirical formula for semiconductive metal oxides is proposed relating nonstoichiometric value x to a temperature or an oxygen partial pressure such that experimental data can be represented more accurately by the formula than by the well-known Arrhenius-type equation. The proposed empirical formula is log x = A + $B{\cdot}1000/T\;+\;C{\cdot}$exp$(-D{\cdot}1000/T)$ for a temperature dependence and $log\;{\times}\;=a\;+b{\cdot}log\;Po_2\;+\;c{\cdot}$exp$(-d{\cdot}log\;Po_2)$ for an oxygen partial pressure dependence. The A, B, C, D and a, b, c, d are parameters which are evaluated by means of a best-fitting method to experimental data. Subsequently, this empirical formula has been applied to the n-type metal oxides of $Zn_{1+x}O,\; Cd_{1+x}O,\;and\;PrO_{1.8003-x}$, and the p-type metal oxides of $CoO_{1+x},\; FeO_{1+x},\;and\;Cu_2O_{1+x}$. It gives a very good agreement with the experimental data through the best-fitted parameters within 6% of relative error. It is also possible to explain approximately qualitative characters of the parameters A, B, C, D and a, b, c, d from theoretical bases.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1999년도 추계종합학술대회 논문집
• /
• pp.507-510
• /
• 1999

Inspection of BGAs presents several challenges for modem measurement equipment. No only must these systems be fast and accurate, they must deal with the special challenges presented by very small shiny metal spheres. For accurate measurement, we propose an algorithm which fits for estimating the accurate ball height using 2-D curve-fitting algorithm. The real boundary between two adjacent pixels and the real ball diameter are measured with subpixel accuracy Experimental results show that the proposed method calculates the ball height and diameter with subpixel accuracy and is robust in local noise with low measurement error.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2004년도 학술대회지
• /
• pp.784-786
• /
• 2004

Overlap errors and side-lobes can be simultaneously solved by the rule-based correction using scattering bars with the rules extracted from test patterns. Process parameters affecting the attPSM lithography simulation have been determined by the fitting method to the process data. Overlap errors have been solved applying the correction rules to the metal patterns overlapped with contact/via. Moreover, the optimal insertion rule of the scattering bars has made it possible to suppress the side-lobes and to get additional pattern fidelity at the same time.