• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.9
• /
• pp.961-966
• /
• 2009

In this paper, a novel voltage-controlled oscillator(VCO) using the metamaterial broadside coupled spiral resonators(BC-DSRs) is presented for reducing the phase noise. For reducing of the phase noise, the series spiral structures have been applied for the signal plane and ground plane at each in order to have the large coupling. Compared with the conventional VCO, the proposed VCO has the larger coupling coefficient constant, which makes a higher Q-factor and has reduced the phase noise of the VCO. The proposed VCO has the phase noise of $-121{\sim}-117.16\;dBc$/Hz at 100 kHz in the tuning range, $5.749{\sim}5.853\;GHz$. The figure of merit(FOM) of this VCO is $-198.45{\sim}-194.77\;dBc$/Hz at 100 Hz in the same tuning range, respectively.

• Journal of Aerospace System Engineering
• /
• v.13 no.3
• /
• pp.56-63
• /
• 2019

Performance analyses were performed on a propeller developed for use in a PAV (Personal Air Vehicle) under 600 kg Maximum Take-Off Weight (MTOW). The actuator disc theory and CFD analyses were used to estimate the hovering time with regards to MTOW variation for a given battery weight. The interference induced power factor kint was introduced to account for the effect of flow interference between the propellers and to estimate the performance of counter-rotating propellers. The Maximum Figure of Merit (FM) value of the propeller pitch was determined and the design RPM range for the required power inversely obtained from the CFD results. Previous research indicate that the flight time of large multi-copter is limited by the available battery energy density. Similarly, the propeller pitch settings and spacing are important factors in reducing the kint value.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.05a
• /
• pp.127-131
• /
• 2006

There are being a lot of studies for achievement of high speed Dehydration, high-strength and Lightweight of washing machine in the latest washing machine business. It is essential that Press-joining Strength of Spin Drum Seaming division is improved .to attain that target. Generally, we are using Mechanical press-joining by Seaming and T.I.G (Tungsten Inert Gas) welding among part joint method. Mechanical press-joining method that is mainly using for Stainless Steel (STS430) Drum have lots of merit that consumption of energy is low more than welding and production costs cut down and generation of the corrosion is solved by removing weld zone defect and materials having different properties are enable to join without special equipment. But, it is difficult to realize joint strength required at high speed operation because joint strength of mechanical press-joining method is low remarkably in comparison with welding. Also, there are a lot of analysis difficulties and very limited research is under way due to the dynamic factor such as multistage plastic working, elastic recovery, residual stress etc. The results of this study show optimal joining condition for mechanical press-joining by performing lots of tensile joining strength test with various specimen under multi-change of important design factor such as seaming width, bead area and bead depth etc.

• Culinary science and hospitality research
• /
• v.10 no.2
• /
• pp.1-15
• /
• 2004

This research was accomplished to prove that the actual using conditions of the funtional bakery products would be different by their sex, age group and income, and what would be main factor to choose them. This survey was examened for 268 subjects by the self-administered questionnaire method. 37% of subjects used the funtional bakery products once or twice a week. They normally paid for them 1,000-3,000 won(40%). The biggest merit of the fuctional bakey products was good for health, but high price was the weekest point of them. Over 63% of subjects answered they had the will to use the new functinal bakery products if they would be developed. Mainly they got the information of functional procuts in bakery. Females paid more than males to buy them and had stronger will to use the new procuts. As the age increased, the using frequency of fuctional bakery products also increased. The expences to buy for them once and the will to use new products increased according to income increment. Females thought more important factors as price, taste, and color than males. Twenties and forties answered price was more important than thirties and fifties.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.53-53
• /
• 2018

Thermoelectric materials can convert directly waste heat to electricity and vice versa. The improvement of the thermoelectric efficiency strongly depends on the dimensionless figure of merit, $ZT=S^2{\sigma}T/{\kappa}$, where S is the Seebeck coefficient, ${\sigma}$ is the electrical conductivity, T is the absolute temperature, and ${\kappa}$ is the thermal conductivity. The thermal conductivity consists of the electronic contribution (${\kappa}_e$) and phonon contribution (${\kappa}_{ph}$). It is very challenge to increase the power factor, $S^2{\sigma}$ and to reduce the thermal conductivity simultaneously because the power factor and electronic thermal conductivity are coupled. One strategy is to decrease the phonon thermal conductivity. The phonon thermal conductivity can be decreased by controlling the grain size and structural defects such as dislocations and twinning. In order to achieve enhancements in thermoelectric efficiency, microstructures that can form numerous interfaces have been investigated intensively for controlling the transport of charge carriers and heat carrying phonons. In this presentation, we report the heterogeneous microstructure of $Mg_2Si_{0.6}Sn_{0.4}$ thermoelectric materials and investigation of its influence on thermoelectric properties.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.45 no.4
• /
• pp.558-561
• /
• 1996

PZT powders were prepared by the molten salt synthesis method. The porous PZT ceramics were made from a mixture of PZT and polyvinylalcohol(PVA) by BURPS(Burnout Plastic Sphere) technique. The porous PZT bodies were fabricated from the green compacts with various amounts of PVA spheres. The piezoelectric coefficient d$_{33}$ (334~350*10$^{-12}$ C/N)of porous PZT ceramics(364*10$^{-12}$ C/N). The figure of merit(d$_{h}$g$_{h}$) of porous PZT specimens evaluating the sensitivity for ultrasonic transducer applications was improved significantly(11~70times) in comparison with that of single phase PZT ceramics(100*10$^{-15}$ m$^{2}$/N). The thickness mode coupling factor k$_{t}$(0.5~0.6) of porous specimens was comparable with that of single phase PZT ceramics(k$_{t}$=0.7). The mechanical quality factor of porous PZT specimens was smaller than 10, and thus these porous PZT ceramics would be believed as a good candidate for broad band hydrophone applications. (author). 10 refs., 7 figs.igs.igs.

• Proceedings of the KIEE Conference
• /
• 1997.07f
• /
• pp.2210-2212
• /
• 1997

A sensorless input current controller for three phase PWM converter is proposed. A merit of this controller is that sinusoidal input line current, unity power factor, and ripple-free DC voltage can be achieved with low-cost. The paper describes the proposed control strategy and its implementation. Simulation result for the proposed controller is compared with that of the sensor based version.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.11 no.3
• /
• pp.36-41
• /
• 1974

Two realigation procedures of any open-circuit transfer functions are presented through the use of genera1ized immitance converters composed of two operational amplifiers and passive elements. The fast precedure is to select the admittance conversion, h(s), to be k/s , and the second one to be k/s. The merit of the second procedure is the elimination of capacitors in passive networks, however, requires more CGIC's than the first. The second-order transfer function is realiged in the two methods under discussion to find that the sensitivity of Q factor and the undamped oscillation frequency to the variation of circuit elements. The first procedure proved to be favorable from the view point of sensitivities.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.11a
• /
• pp.604-607
• /
• 2003

Recently, hybrid concrete structures such as a concrete-filled steel tubular(CFT), a steel reinforced concrete(SRC) and a composite material are popular in structure applications. They also have merit of high strength, high ductility, and large energy absorption capacity. But the analysis of hybrid concrete structures is very difficult owing to the complex behavior of concrete under passive confinement. This paper has analyzed CFT, which receives passive confinement using Tri-Surface concrete model for three dimension finite element analysis. By the result of that, the proposed model was properly forecasted a concrete behavior that receives passive restraint as well as non-linear analysis of concrete which receive uniaxial stress and high active confinement of 400Mpa. If the model through the steady study is set up especially on the factor of concrete under passive confinement, the proposed concrete model will be surely useful for analysis of the hybrid concrete structures.

• KIEAE Journal
• /
• v.15 no.4
• /
• pp.5-11
• /
• 2015

Purpose: Recently, renewable energy system has been widely used to reduce the energy consumption and CO2 emission of building. A photovoltaic/thermal(PVT) system is a kind of efficient energy uses, which is combined with photovoltaic module and solar thermal collector. PVT system removes heat from PV module by through thermal fluid to raise the performance efficiency of the PV system. However, though PVT system has the merit of the improved efficiency in theoretical approach, there have been few performance analysis for PVT system using the dynamic energy simulation. In this study, in order to establish the optimum design method of this system, simulation was conducted by using individual system modules. Method: For the dynamic simulation, TRNSYS17 was used and local weather data was utilized. Furthermore, the system performance in various installation condition was calculated by case studies. Result: As a result, the amount of electric generation and heat production in each case was found by the simulation. The gap of system performance was also evident according to the installation condition.