• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.7
• /
• pp.877-884
• /
• 2004

In this paper, structural analysis is performed to investigate the deformation of porous media in a proton exchange membrane fuel cell (PEMFC). Structural deformation of air plate of the fuel cell causes the change in configuration and cross sectional area of the channel. The distributions of mass flow rate and pressure are major factors to decide the performance of a PEMFC. These factors are affected by channel configuration of air plate. Two kinds of numerical air plate models are suggested for flow analyses. Deformed porous media and undeformed porous media are considered for the two models. The Numerical flow analysis results between deformed porous media and undeformed porous media have some discrepancy in pressure distribution. The pressure and velocity distribution under a working condition are numerically calculated to predict the performance of the air plates. Pressure and velocity distributions are compared for two models. It is shown that structural deformation makes difference in flow analysis results.

• Polymer(Korea)
• /
• v.30 no.2
• /
• pp.175-181
• /
• 2006

Hybrid process of thermally-induced phase separation and stretching was developed for the preparation of microporous polypropylene hollow fiber membranes. Precursor for stretching was prepared by using soybean oil as a diluent and benzoic acid as a nucleating agent far the sphenlite control and it was stretched far the micrporous hollow fiber membrane. The effects of stretching ratio and deformation rate for stretching process were investigated. Increase of stretching ratio resulted in the greater pore size with nonuniform size distribution. Higher deformation rate also increaser the pore size with uniform size distribution. Stretching ratio was closely related with the orientation of polymer chain and increased the mechanical strength of the fiber. Increase of deformation rate had little effects on the orientation of crystalline phase, and decreased the orientation of amorphous phase which caused the decrease of tensile strength of the fiber and broke the micro-fibrils connecting spherulites to form a circular pore shape.

• Journal of the Korean Institute of Gas
• /
• v.9 no.3 s.28
• /
• pp.27-31
• /
• 2005

The membrane to be applied inside of the LNG storage tank is provided with corrugations to absorb thermal contraction and expansion caused by LNG temperature and pressure changes. It is very important to measure their thermal strains under LNG temperature by analytical and experimental stress analysis of the membrane. We have developed a stress measurement system using strain gages and measured the strain during cooldown and storing the LNG. We also analyzed the measured data by comparison with the FEM data.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.11 no.3
• /
• pp.1-10
• /
• 1991

The paper is concerned with the analysis of laminated composite shell structures using an improved degenerated shell element. In the formulation of the element stiffness, the combined use of three different techniques was made. They are; 1) an enhanced interpolation of transverse shear strains in the natural coordinate system to overcome the shear locking problem; 2) the reduced integration technique in in-plane strains to avoid the membrane locking behavior; and 3) selective addition of the nonconforming displacement modes to improve the element performances. This element is free of serious shear/membrane locking problems and undesirable compatible/commutable spurious kinematic deformation modes. An incremental total Lagrangian formulation is presented which allows the calculation of arbitrarily large displacements. The resulting non-linear equilibrium equations are solved by the Newton-Raphson method. The versatility and accuracy of this improved degenerated shell element are demonstrated by solving several numerical examples.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.10
• /
• pp.84-92
• /
• 2010

In this study a numerical analysis has been conducted for the flow characteristics and pumping performance of a piezoelectric-based micropump with electromagnetic resistance exerted on electrically conducting fluid. Here, electromagnetic resistance is alternately applied at the inlet and outlet with alternately applied magnetic fields in association with the reciprocal membrane motion of the piezoelectric-based micropump. A model of Prescribed Deformation is used for the description of the membrane motion. The internal flow characteristics and pumping performance are investigated with the variation of magnetic flux density, tube size, displacement of membrane and the frequency of the membrane. It turns out that the current micropump has a wide range of pumping flow rate compared with diffuser-nozzle based micropumps.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.26 no.12
• /
• pp.1685-1693
• /
• 2002

다양한 용도로 사용되고 있는 라미네 이 팅 직물은 주로 별도로 제조된 고분자 필름 또는 막을 접착제, 열, 압력 등을 이용하여 기포(基布)와 결합시키는 방법으로 제조되어 진다. 이축연신시킨 Poly(tetrafluoroethylene) (PTFE) sheet는 매우 우수한 높은 투과성을 지니는 다공성 물질이 며, 본 연구에서는 이 막을 나일론 직물에 라미네이팅시킨 투습방수직물을 시료로 사용하여 라미네이팅 후의 역학특성 변화를 분석 하였다. 라미네이팅에 따른 투습방수직물의 물성과 역학특성의 변화에 관하여 살펴본 결과 다음과 같은 결과를 얻었다. 3-layer 라미네이팅 직물(base fabric-PTFE membrane-knitted lining)의 인열강도는 2-layer라미네이팅 직물 (base fabric-PTFE membrane)에 비해 매우 높게 나타났으며, 가공 전 직물과 비교하여 코팅직물에서 나타난 것과 같은 인열강도의 감소는 나타나지 않았다. 직물-PTFE 막 복합체 의 경우, 라미네 이 팅 이 파단강도 및 파단신도 의 증가에 기여 한 것으로 나타났으며 특히 3-layer 라미네이팅 직물의 경우, 신장률이 20%를 넘어서면서 강도가 현저히 증가하였다. 의복을 착용하였을 때 가해질 수 있을 정도의 소변형(small deformation) 하에서의 역학특성 에 있어서는 라미네이팅에 의해 전단특성이 가장 유의한 변화를 나타내었다. 전단강성(G)과 전단 히스테리시스 (2HG,2HG5)모두 증가하였고, primary hand value 중에서는 stiffness 가장 현저한 증가를 나타내었다

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.4
• /
• pp.417-424
• /
• 2007

This paper reports fabrication and characterization of a pressure sensor using a pitch-based carbon fiber. Pitch-based carbon fibers have been shown to exhibit the piezoresistive effect, in which the electric resistance of the carbon fiber changes under mechanical deformation. The main structure of pressure sensors was built by performing backside etching on a SOI wafer and creating a suspended square membrane on the front side. An AC electric field which causes dielectrophoresis was used for the alignment and deposition of a carbon fiber across the microscale gap between two electrodes on the membrane. The fabricated pressure sensors were tested by applying static pressure to the membrane and measuring the resistance change of the carbon fiber. The resistance change of carbon fibers clearly shows linear response to the applied pressure and the calculated sensitivities of pressure sensors are $0.25{\sim}0.35 and 61.8 ${\Omega}/k{\Omega}{\cdot}bar$ for thicker and thinner membrane, respectively. All these observations demonstrated the possibilities of carbon fiber-based pressure sensors.

• Journal of Sensor Science and Technology
• /
• v.28 no.1
• /
• pp.1-6
• /
• 2019

This paper presents an air flow sensor (AFS) based on a polymer thin film. This AFS primarily consists of a polymer membrane attached to a metal-patterned glass substrate and a temperature-sensing element composed of NiCr. These two components were integrated on a single glass substrate. The AFS measures changes in capacitance caused by deformation of the polymer membrane based on the air flow and simultaneously detects the temperature of the surrounding environment. A readout integrated circuit (ROIC) was also fabricated for signal processing, and an ROIC chip, 1.8 mm by 1.9 mm in size, was packaged with an AFS in the form of a system-in-package module. The total size of the AFS is 1 by 1 cm, and the diameter and thickness of the circular-shaped polymer membrane are 4 mm and $15{\mu}m$, respectively. The rate of change of the capacitance is approximately 11.2% for air flows ranging between 0 and 40 m/s.

• Journal of Aerospace System Engineering
• /
• v.10 no.4
• /
• pp.1-10
• /
• 2016

This study analyzes the fabric skin of a wind turbine blade. The fabric skin is a membrane structure that was analyzed using a static Fluid Structure Interaction (FSI) method. For this study the blade of large 5 MW wind turbine was selected. In order to examine the validity of the analysis, a variety of reference data were used. Before conducting static FSI analysis, a Computational Fluid Dynamics (CFD) analysis and modal analysis were done. Then interaction analysis was conducted. FSI analysis was done with imported Aerodynamic data that resulted from the CFD analysis. The resulting observations about the membrane structure, inherent tensions, deformation of the final structure, and aerodynamic forces caused by deformation are reported.

• Journal of Sensor Science and Technology
• /
• v.24 no.6
• /
• pp.379-384
• /
• 2015

An infrared image sensor is a core device in a thermal imaging system. The fabrication method of a focal plane array (FPA) is a key technology for a high resolution infrared image sensor. Each pixels in the FPA have $Si_3N_4/SiO_2$ membranes including legs to deposit bolometric materials and electrodes on Si readout circuits (ROIC). Instead of polyimide used to form a sacrificial layer, the feasibility of an amorphous silicon (${\alpha}-Si$) was verified experimentally in a $8{\times}8$ micro-bolometer array with a $50{\mu}m$ pitch. The elimination of the polyimide sacrificial layer hardened by a following plasma assisted deposition process is sometimes far from perfect, and thus requires longer plasma ashing times leading to the deformation of the membrane and leg. Since the amorphous Si could be removed in $XeF_2$ gas at room temperature, however, the fabricated micro-bolomertic structure was not damaged seriously. A radio frequency (RF) sputtered nickel oxide film was grown on a $Si_3N_4/SiO_2$ membrane fabricated using a low stress silicon nitride (LSSiN) technology with a LPCVD system. The deformation of the membrane was effectively reduced by a combining the ${\alpha}-Si$ and LSSiN process for a nickel oxide micro-bolometer.