• Proceedings of the KIEE Conference
• /
• 2004.07d
• /
• pp.2504-2506
• /
• 2004

상용화된 프로토콜인 TCP/IP에 기반한 원격제어시스템을 구현하였다. 본 논문은 서보시스템의 제어 파라메터 설정에서부터 통신 프로토콜 설계에 이르기까지 시스템 구성과 이를 구현하기 위한 방법을 소개하기 위해 작성되었다. 연구결과의 실험장치를 통해 그 성능을 평가하였으며 시간지연, 신호데이터의 정확성 및 사용의 편리성 등 모든 측면에서 괄목할만한 실험결과를 기록하였다. 본 논문의 성과는 유사한 서보시스템의 응용과 활용에 기여할 것으로 본다.

• Proceedings of the KIPE Conference
• /
• 2005.07a
• /
• pp.427-429
• /
• 2005

In order to tune the speed controller in the linear servo applications the accurate information of a mover mass including a load mass is always required. This paper suggests the mass estimation method of a permanent magnet linear synchronous motor(PMLSM) by using the parameter estimation method of Least-Squares algorithm. First, the deterministic autoregressive moving average(DARMA) model of the mechanical dynamic system is derived. The application of the Least-Squares algorithm shows that the mass can be accurately estimated both in the simulation results and in the experimental results.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.2
• /
• pp.37-43
• /
• 2005

A haptic steering system which reflects steering reaction torque has been developed for a fixed base vehicle simulator. The haptic steering system consists of a steering effort sensor, MR-clutch, AC servo motor and controller. In order to generate realistic steering torque feel to driver and at the same time to meet real-time simulation requirement, 3D torque map is constructed by experimental data and torque generation algorithm using the torque map has been also developed. 3D torque map is constructed using curve fitting and interpolation of the measured values of the steering angle, velocity and steering torque from actual slalom test on the proving ground. In order to carry out performance test of the developed haptic steering system, a fixed based vehicle simulator is constructed by integrating real time vehicle dynamics module, VR-video/audio module, and the haptic steering system. Steering torque and steering angle curves have been obtained from virtual testing in the vehicle simulator and performance of the haptic steering system has been evaluated.

• Journal of the Korean Society for Precision Engineering
• /
• v.32 no.5
• /
• pp.431-439
• /
• 2015

One of common challenges in designing modern production machines is realizing high speed motion without sacrificing accuracy. To address this challenge it is necessary to maximize the stiffness of the mechanical structure and the control system with consideration on the main disturbance input, cutting forces. This paper presents analysis technologies for realizing high stiffness in production machines. First, CAE analysis techniques to evaluate the dynamic stiffness of a machine structure and a new method to construct the physical machine model for servo controller simulations are demonstrated. Second, cutting forces generated in milling processes are analyzed to evaluate their effects on the mechatronics system. In the effort to investigate the interaction among the structure, controller, and process, a flexible multi-body dynamics simulation method is implemented on a magnetic bearing stage as an example. The presented technologies can provide better understandings on the mechatronics system and help realizing high stiffness production machines.

• Journal of Drive and Control
• /
• v.16 no.4
• /
• pp.93-100
• /
• 2019

Nuclear and thermal power plants must provide the turbines with an appropriate degree of high temperature and high pressure steam, to produce the optimum electricity. Additionally, in the event of system and power system failure during electrical production, the steam is immediately disabled, to protect the turbines and generators rotating at high speed. The plant thus uses a special steam control valve system for turbine control, which is opened by force of the hydraulic servo actuator and closed by a large steel spring force. In this study, the causes of failure of the turbine control valve system, a key device of the power plants, were analyzed, and the causes of failure were improved relative to reliability of the equipment.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.10
• /
• pp.122-129
• /
• 2008

This paper deals with precise positioning of a high-speed positioning stage without inducing residual vibration by using an input shaping technique. Input shaping is well known to be a very effective tool for suppressing the residual vibration of flexible structures. However, the ordinary input shaping for positioning stages is designated mostly for velocity regulation, not for the residual vibration at the target position. The main difficulties in implementing input shaping along with precise positioning are the time delay caused by the servo system characteristics and the s-curve feature often employed in some motor controllers. This paper analyzes the dynamic responses of a single-mode-dominate stage system subjected to input shaping. A theoretical model is developed io investigate the nature of system. In order to overcome the difficulty, this paper proposes an improved input shaper based on modified command profile generation. The proposed method is proved effective through experiments and simulations.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.1
• /
• pp.146-153
• /
• 1996

A SCARA type direct drive robot which can be used in the assembly operation was designed and manufactured. Graphite fiber epoxy composite material was used in the fabrication of the robot arm structure in order to improve the speed of the robot arm with a high damping effect. For model-based control and sensitivity analysis of system parameters, the dynamic model of robot arm and drive servo amplifier parameters such as equivalent gains of PWM driver and velocity gains of servo system were estimated from frequency response tests. The complete dynamic model for overall robot system was used in the simulation of the open-loop control. The simulation results agreed reasonably well to the experimental results. The feedforward control using the dynamic models improved the trajectory tracking performance, decreasing the tracking error by factor of three compared with PID control. This study found that the inverse dynamic model of the robot arm including the drive servo system showed better performances than the case of arm dynamic model only.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.12 no.2
• /
• pp.162-169
• /
• 2019

Non-destructive freshness measurement using spectroscopy has been carried out several times, but research on freshness and freshness has not been conducted. Therefore the purpose of this study is to develop a system for visually measuring and quantifying the air sack inside the egg by non - destructive method. The experimental environment which designed a small chamber was composed of 850nm band of two IR lasers, IR camera and two servo motors to acquire air sack Images. When the air sack volume ratio is 2.9% or less and the density is 0.9800 or more, the Haugh Unit value is 60 or more It was judged to be a fresh egg of a grade B or higher. These results mean, using the weight measurement, nondestructive decision system, and freshness evaluating algorithm. It can be expected to distinguish grade B or more marketable eggs without using destructive methods.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.906-908
• /
• 2002

The technical improvement of servo system, it is required to study on robust control method in company. It needs to study on brake system that has constant torque-speed performance as load variation. In this paper, braking torque characteristics of eddy current braker between electromagnet stator and rotating disk are analyzed. The torque-speed characteristics and proper disk construction are presented. From the computer simulation results, it was found that eddy current braking torque is linear or approximately constant over the desired speed range depending on the rotor material, disk construction, pole number and pole displacement of stator. The relationship of these parameters are confirmed by experimental result.

• Journal of the Korean Society of Industry Convergence
• /
• v.11 no.3
• /
• pp.135-140
• /
• 2008

This paper researched about Development Cutting Tool User Defined Module Based(PMCUDMS) on Simulation that was able to adapt themselves to rapid development of software and hardware to adopt. It is basic research that develops a scheme whereby technic make property. This paper theorized about to realize Cutting Tool User Defined Module Based on Simulation which is developing CNC Software flows from building Windows XP operating system's image that is possible realtime acting and multitasking to correct. And Cutting Tool User Defined Module Based on Simulation component which was consisted of basis OS, NC Code parser, Servo Motor Control, Simulator, Man-Machine Interface.