• Korean Journal of Food Science and Technology
• /
• v.37 no.4
• /
• pp.567-573
• /
• 2005

Compatability of films made of chitosan, gelatin, and their blends prepared by aqueous solution casting was investigated using a thermogravimetric analyzer(TGA) and a dynamic mechanical analyzer (DMA). TGA showed gelatin is more thermally stable than chitosan, and thermal stability of chitosan in blends was higher than that of pure chitosan due to interaction among functional groups of component polymers in blend. Glass transition temperature $(T_g)$ of blends was dependent on chitosan content of blends. Blend films exhibited good miscibility. Moisture and glycerol contents of blend strongly affected thermal properties of two component polymers.

• Polymer(Korea)
• /
• v.28 no.2
• /
• pp.143-148
• /
• 2004

${\alpha}$,$\omega$-Hydrogen polyorganosiloxane(HPMDMS) prepolymer was prepared from equilibrium polymerization ofoctamethylcyclotetrasiloxane, 1,3,5-trimethylcyclotrisiloxane, 1,3,5,7-tetravinyl-1,3,5,7-tetramethyl-cyclotetrasiloxane, and 1,1,3,3-tetramethyl disiloxane as an end-blocker in the presence of tetramethylammonium siloxanolate as a catalyst. Polyorganosiloxane modified with dimethylacrylamide(APMDMS) was prepared by hydrosilylation of HPMDMS with dimethylacrylamide in the presence of Pt catalyst, and followed by coordination of metal oxide (APMDMS-MO), such as NiO and FeO, to the amide moieties of the resulting polymer. The chemical structures of HPMDMS and APMDMS were confirmed by FT-IR and $^1$H-NMR analysis. Liquid silicone rubber containing metal oxide composite (LSRMO) was prepared by compounding APMDMS-MO, ${\alpha}$,$\omega$-vinylpolydimethylsiloxane, and a catalyst in a high speed dissolver. The thermal conductivity of LSRMO composite was determined to be 0.29 W/mK, and the volume resistivity exhibited a lower value than that of LSR composite. The mechanical and thermal properties of LSRMO and LSR composite were measured by UTM and TGA.

• Polymer(Korea)
• /
• v.27 no.5
• /
• pp.470-476
• /
• 2003

In order to obtain high refractive plastic materials, 1,2 -ethylenedisulfanylbis(2-mercaptomethyl-1-ethanthiol) (ESTT) was newly prepared in good yield by the reaction of 1,2-ethylenedisulfanylbis(2-bromomethyl-1-ethanthiol) (ESTB) with thiourea followed by hydrolysis using an aqueous ammonia solution and characterized by $^1$H-NMR (-SH at 1.7 ppm), $\^$13/C-NMR(-CH$_2$SH at 28.4 ppm) and FT-IR (-SH at 2540 cm$\^$-1/) spectroscopy, etc. Polythiourethanes (PTU) were obtained from the combinations of ESTT with each of 4,4＇-methylenebis(phenylisocyanate) (MDI), tolyene 2,4-diisocyanate (TDI), isophorone diisocyanate (IPDI), mxylene diisocyanate (XDI), and 1,6-diisocyanatohexane (HMDI) in the presence of dibutyltin dilaurylate as a catalyst, in a casting mold, and characterized by FT-IR (existence of N=C=O) spectroscopy and elemental analyzer (sulfur content). Accordingly, their thermal, mechanical and optical properties were investigated by using DSC, TGA, hardness tester and refractometer: both the melting point on DSC and crystallinity on X -ray diffraction (XRD) for specimens of PTUs were not observed. PTUs with T$\_$g/s above 110 $^{\circ}C$ showed good hardness (Shore D) in the range of 86 to 89. Thermal stabilities of PTUs obtained by using ESTT and each of diisocyanates containing aromatic rings were especially good. Also, the optical transmittances of amorphous PTUs through UV-visible source in the range of 400 to 600 nm were good. PTUs showed refractive indexes above 1.60, and their refractive indexes gradually increased with increase of sulfur contents.

• Polymer(Korea)
• /
• v.29 no.3
• /
• pp.248-252
• /
• 2005

PP/MMT nanocomposites having a various compositions were prepared by melt blending with a twin screw extruder. In this study, maleic anhydride-grafted PP (MAH-g-PP) was used as a compatibilizer in order to assist the exfoliation or hen in the pp matrix. from the results or x-ray diffraction (XRD) and transmission electron microscope (TEM) measurements for the nanocomposites, we confirmed that MMT was exfoliated. PPM nanocomposites have shown good flame retardancy by synergistic effect between MMT and flame retardant. The mechanical and thermal properties of the nanocomposites showed significant enhancement compared with those of neat PP, The excellent flame retardancy of the PP/MMT nanocomposites, UL94 V-0 value, was successfully obtained with reduced amount of the flame retardant.

• Korean Journal of Materials Research
• /
• v.30 no.1
• /
• pp.38-43
• /
• 2020

Sand casting 3D printing uses a binder jetting method to produce a mold having complicated shape by spraying a binder on sand coated with activator. Appropriate heat treatment process in sand mold fabrication can increase the degree of polymerization to improve flexural strength. However, long heat treatment of over 24 hours decreases flexural strength and reliability due to chemical bond decomposition through thermal degradation. The main role of the activator is to control the reaction rate between the polymer chains. As a result, when the activator composition is increased from 0.15 wt% to 0.25 wt%, the flexural strength is increased by 218 N/㎠. However, excess activator (0.40 wt%) has been shown to decrease reliability without increasing flexural strength. The main role of the binder is to control the flexural strength of the specimen. As the binder composition is increased from 2.00 wt% to 4.00 wt%, the flexural strength increases to about 255 N/㎠, indicating the maximum flexural strength increase. Finally, the reliability of the flexural strength of the fabricated specimens is evaluated by a Weibull plot. Weibull modulus calculations are used to evaluate the flexural strength reliability of the specimens, and maximum reliability value of 11.7 is obtained at 0.20 wt% activator composition. Therefore, it is confirmed that this composition has maximum flexural strength reliability.

• Korean Journal of Materials Research
• /
• v.22 no.2
• /
• pp.61-65
• /
• 2012

A $Li_2O-2SiO_2$ ($LS_2$) glass was investigated as a lithium-ion conducting oxide glass, which is applicable to a fast ionic conductor even at low temperature due to its high mechanical strength and chemical stability. The $Li_2O-2SiO_2$ glass is likely to be broken into small pieces when quenched; thus, it is difficult to fabricate a specifically sized sample. The production of properly sized glass samples is necessary for device applications. In this study, we applied spark plasma sintering (SPS) to fabricate $LS_2$ glass samples which have a particular size as well as high transparency. The sintered samples, $15mm\phi{\times}2mmT$ in size, ($LS_2$-s) were produced by SPS between $480^{\circ}C$ and $500^{\circ}C$ at 45MPa for 3~5mim, after which the thermal and dielectric properties of the $LS_2$-s samples were compared with those of quenched glass ($LS_2$-q) samples. Thermal behavior, crystalline structure, and electrical conductivity of both samples were analyzed by differential scanning calorimetry (DSC), X-ray diffraction (XRD) and an impedance/gain-phase analyzer, respectively. The results showed that the $LS_2$-s had an amorphous structure, like the $LS_2$-q sample, and that both samples took on the lithium disilicate structure after the heat treatment at $800^{\circ}C$. We observed similar dielectric peaks in both of the samples between room temperature and $700^{\circ}C$. The DC activation energies of the $LS_2$-q and $LS_2$-s samples were $0.48{\pm}0.05eV$ and $0.66{\pm}0.04eV$, while the AC activation energies were $0.48{\pm}0.05eV$ and $0.68{\pm}0.04eV$, respectively.

• Polymer(Korea)
• /
• v.35 no.1
• /
• pp.52-59
• /
• 2011

L-PLA or D-PLA was synthesized in bulk at $140^{\circ}C$ by ring opening polymerization(ROP) of L-lactide or D-lactide as a monomer using tin(II) octoate and lauryl alcohol as a catalyst and an initiator with changing the amounts of catalyst(0.25~1.0 wt%) and initiator(0.l~0.5 wt%). And stereocomplex-PLA was prepared by L-PLA/D-PLA having a wide range of molecular weight(30000~90000 g/mol) and L-PLA/D-PLA blends having different mixing ratio ($X_D$). The melting temperature. thermal degradation temperature and thermal stability of stereocomplex-PLA were higher than those of homopolymers(L-PLA, D-PLA). We supposed that these improvements arose from a strong interaction between L-PLA and D-PLA. The improved mechanical properties and changes in morphology of LPLA/D-PLA blends were compared to those of homopolymers(L-PLA, D-PLA).

• Applied Chemistry for Engineering
• /
• v.17 no.2
• /
• pp.177-182
• /
• 2006

In this work, we have prepared organophilic MMT having thermal stability by ion exchange reaction of various aromatic ammonium salts with MMT containing sodium ion. The organic modifiers having alkyl side chains and amine functional group were successfully synthesized by effectively introducing the surfaces of MMT via ion exchange reaction to form organophilic MMTs with a view to improve the reactivity and thermal stability. The WAXD patterns of organophilic MMT showed the more increased gallery spacing by $3.3{\AA}$ than that of the pristine MMT and also the onset of initial decomposition of organophilic MMT was $275^{\circ}C$ as determined by a thermogravimetric analysis. The polyimide (PI) nanocomposite films based on poly(amic acid) and organophilic MMT were prepared by a solution blending followed by cyclodehydration reaction. We have investigated the dispersity of organophilic MMTs in PI matrix by using WAXD and the effect of the organophilic MMT content on the mechanical properties of PI nanocomposite films was studied.

• Journal of the Korean Ceramic Society
• /
• v.42 no.3 s.274
• /
• pp.155-164
• /
• 2005

The characteristics of sintering for Mullite-Cordierite (MC) composites and the effect of $TiO_2$ addition were studied. The MC composites were manufactured by a solution-polymerization method using PVA as a polymer carrier, and $TiO_2$ was used as a sintering agent. They were calcined at $1300^{\circ}C$, planetary milled for 4 h and sintered at $1450^{\circ}C$. As cordierite content increased, relative density of materials was increased up to $98\%$ and sinterability was improved. In case of $50\;wt\%$ mullite/$5\;wt\%$ cordierite composition sintered for 16 h, the flexural strength and thermal expansion coefficient were 190 MPa and $3.07{\times}0^{-6}/^{\circ}C$, respectively. However, mechanical properties were decreased with the cordierite contents higher than $50\;wt\%$ because of the excess liquid-phase amount. As the addition of $TiO_2$ is increased, columnar crystal of mullite and liquid-phase contents were increased. In particular, the flexural strength and thermal expansion coefficient decreased in case of $5\;wt\%\;TiO_2$ addition.

• Journal of the Korean Electrochemical Society
• /
• v.17 no.1
• /
• pp.7-12
• /
• 2014

There is increasing demand on the reducing the weight and the volume of the major components in lithium secondary battery to improve energy density. Separator not only provides pathway for lithium ion movement but also prevents direct contact between anode and cathode. Herein we fabricated polyethylene separator by varying biaxial stretching ratio to obtain membrane thickness of 16, 12, and $9{\mu}m$. Mechanical and thermal properties of the separator with different thickness were investigated. Also rate capability and charge-discharge cycle property up to 500 cycles were studied using coin type full-cell with $LiCoO_2$ and graphite as a cathode and an anode, respectively. All the cells using separator with different thickness demonstrated excellent capacity retention after 500cycles (around 80%). Considering the rate capability, cell using separator with thickness of $9{\mu}m$ showed best performance. Interestingly, separator thickness of $9{\mu}m$ was more resistant to heat contraction compared to that of $16{\mu}m$ separator.