• Explosives and Blasting
• /
• v.21 no.4
• /
• pp.23-35
• /
• 2003

This study is to clarify the comparative relationship and a mechanical anisotropy of rock on the subject of granite distributed in the Namwon area Uniaxial compressive and Brazilian strengths with respect to the horizontal and vertical axes of granite are shown the linear relation. In the case of the result of the p-wave velocity measurement. it is represented that the velocity of vortical direction is faster about 10 to 15% than other two horizontal directions. The difference between velocities is caused by a developmental pattern of microcracks distributed in rock. Moreover, this result is very consistent with the result investigated through thin sections. The proportion of uniaxial compression strength to Index of point load strength ($Is_{(50)}$) is 18~20 times in case of granite. Uniaxial compressive strength is relatively good relationship with point load strength, Schmidt hammer rebound value, and tensile strength point load strength of them is the best comparative relationship. It is indicated that point load test is the most useful tool to estimate uniaxial compressive strength, comparing with other experimental methods.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 1998.04b
• /
• pp.6-6
• /
• 1998

In 1957, the first magnetic disk drive compatible with a movable head was introduced as an external file memory device for computer system. Since then, magnetic disks have been improved by increasing the recording density, which has brought about the development of a high performance thin film magnetic head. The thin film magnetic head has a magnetic circuit on a ceramic substrate using IC technology. The physical property of the substrate material is very important because it influences the tribology of head/disk interface and also manufacturing process of the head. $Al_{2}O_{3}$-TiC ceramics, so called ALTIC, is known to be one of the best substrate materials which satisfies this property requirement. Even though the head is not in direct contact with the disk, frequent instantaneous contacts are unavoidable due to its high rotating speed and the close gap between them. This may cause damage in the magnetic recording media and, thus, it is very important that the magnetic head has a good wear resistance. $Al_{2}O_{3}$-TiC ceramics has an excellent tribological property in head/disk interface. Manufacturing process of thin film head is similar to that of IC, which requires extremely smooth and flat surface of the substrate. The substrate must be readily sliced into the heads without chipping. $Al_{2}O_{3}$-TiC ceramics has excellent machineability and mechanical properties. $Al_{2}O_{3}$-TiC ceramics was first developed at Nippon Tungsten Co. as cutting tool materials in 1968, which was further developed to be used as the substrate materials for thin film head in collaboration with Sumitomo Special Metals Co., Ltd. in 1981. Today, we supply more than 60% of the substrates for thin film head market in the world. In this paper, we would like to present the sintering process of $Al_{2}O_{3}$-TiC ceramics and its property in detail.

• Journal of the Microelectronics and Packaging Society
• /
• v.8 no.4
• /
• pp.1-10
• /
• 2001

Chip-on-glass(COG) mounting of area array electronic packages was attempted by heating the rear surface of a contact pad film deposited on a glass substrate. The pads consisted of an adhesion (i.e. Cr or Ti) and a top coating layer(i.e. Ni or Cu) were healed by the UV laser beam transmitted through the glass substrate. The lather energy absorbed on the pad raised the temperature of a solder ball which is in physical contact with the pad, and formed a reflowed solder bump. The effects of the adhesion and top coating layer on the laser reflow soldering were studied by measuring temperature profile of the ball during the laser heating process. The results were discussed based on the measurement of reflectivity of the adhesion layer. In addition, the microstructures of solder bumps and their mechanical properties were examined.

• Korean Journal of Materials Research
• /
• v.25 no.5
• /
• pp.215-220
• /
• 2015

The effect of Al content on the processing of reaction-bonded $Al_2O_3$ (RBAO) ceramics using 40v/o ~ 80v/o Al-Zn-Mg alloy powder was studied in order to improve traditional RBAO ceramic processes that use ~ 40v/o pure Al powder. The influence of high Al content in starting $Al_2O_3$-Al alloy powder mixtures on its particulate characteristics, reaction-bonding, microstructure, physical and mechanical properties was revealed. Starting $Al_2O_3$-Al alloy powder mixtures with 40v/o ~ 80v/o Al alloy powder were milled, reaction-bonded, post-sintered, and characterized. With an increasing Al alloy content, the milling efficiency of Al alloy powder was lowered, resulting in a larger particle size after milling. However, in spite of the larger particle size of Al alloy powder, the oxidation, i.e., reaction-bonding, of the Al alloy was successfully completed via solid and liquid state oxidation, in which the activation energy of the oxidation was nearly the same regardless of Al alloy content. After reaction-bonding and post-sintering at $1600^{\circ}C$, RBAO ceramics from 80v/o Al alloy content showed a relative density of ~97% and a flexural strength of 251 MPa compared to ~ 96% and 353 MPa for RBAO ceramics from 40v/o Al alloy content, respectively. The lower flexural strength at 80v/o Al alloy content was due to the weak spinel phase that formed from Zn, Mg alloying elements in Al.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.4
• /
• pp.2958-2965
• /
• 2015

The PLGA(Poly lactide-co-glycolide) Copolymer have been actively applied to the medical implant material as biomaterials. PLGA membrane was able to alveoloplasty with osteotomy for favorable degradation characteristics and possibilities for sustained drug delivery. In this study, PLGA membrane was prepared using phase inversion method, and examined to optical method analysis(NMR, IR), mechanical property measurement (tearing strength) and thermal characteristic analysis(DSC). In addition, the biodegradation characteristics of the PLGA membrane filled with a PBS(Phosphate Buffered Solution) of the water bath ($60^{\circ}C$) according to the degree of surface degradation in the degradation time, the pH change of the solution and change of the mass of the membrane were measured.

• Journal of Korea Foundry Society
• /
• v.26 no.6
• /
• pp.267-271
• /
• 2006

Metal foam is a class of attractive materials, which exhibits unique combinations of physical, mechanical, thermal, electrical and acoustic properties. In particular, it is light and good at absorbing energy, which makes it attractive in automotive and aerospace applications weight is critical. In this paper, the Mg alloy foam was prepared by melt foaming method by addition of calcium as thickening agent, and $TiH_2$ or $CaCO_3$ powder as blowing agent. The macrostructural observation of foamed Mg showed that the pore structures of Mg alloy foam made by $CaCO_3$ as blowing agent were much better than that of foams made by $TiH_2$ as blowing agent. In addition, this paper showed the possible reason of fabrication magnesium alloy foam in proportion to blowing agent and the porosity range was about 40 to 76% as results value.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.1D
• /
• pp.73-79
• /
• 2006

A major purpose of this study is to develop high modulus asphalt mixtures for perpetual asphalt pavements which can save maintenance cost by increasing the design and performance periods of the pavements. Various physical and mechanical laboratory tests are performed for the high modulus asphalt binder developed in this study. The test results show that the properties of the high modulus binder are similar to those of the French high modulus binders. In addition to the binder tests, various performance tests are conducted for the high modulus and conventional mixtures. The dynamic modulus test results indicate that the dynamic modulus values of the high modulus mixtures are higher than those of the conventional mixtures by 10~15% at $5^{\circ}C$, 20~25% at $15^{\circ}C$ and 100% at $30^{\circ}C$. It is observed from the performance tests that the high modulus mixtures yield better fatigue, rutting and moisture damage performance than the conventional mixtures.

• International Journal of Highway Engineering
• /
• v.11 no.2
• /
• pp.205-216
• /
• 2009

As a subsequent study, this paper presents a comparative evaluation of structural responses in asphalt pavements with stabilized foundations. The approach based on a finite element analysis which incorporates non-linear behaviors of pavement geomaterials is used to estimate each performance indicator under standard single axle loading condition. In addition, results from laboratory tests are used to provide physical and mechanical properties of stabilized geomaterials for analyzing various pavement structures. Changes in pavement responses with varying layer thickness and stabilizer contents were investigated. It is found that the effect of layer thickness and stabilizer content is a critical factor in structural response of stabilized pavements. Moreover, a design criterion is proposed for selecting minimum contents of stabilizer of coarse-grained geomaterials based on a result of unconfined compressive strength and proper layer thickness of foundations.

• Journal of the Microelectronics and Packaging Society
• /
• v.23 no.4
• /
• pp.101-105
• /
• 2016

Recently, the hydrophobic surface has been attracted because of the excellent opto-physical properties. Various processing methods such as chemical, mechanical, photolithographic and laser processing are competitively introduced for fabrication of hydrophobic surface of polymer, metal and ceramics. In this paper, we fabricated the hydrophobic surface of copper metal by simple method which irradiated 355 nm UV-pulsed laser in order to shape microgrooves and increased surface roughness through oxidation process at room temperature. Finally the contact angle is dramatically increased by maximum $45^{\circ}$, as a result of oxidation which simply created nanostructures on the microstructures without expensive chemical process.

• Journal of the Korea Institute of Building Construction
• /
• v.15 no.2
• /
• pp.177-183
• /
• 2015

In this study, the thermal conductivity, physical and mechanical properties of lightweight aggregate concretes with hollow micro sphere(HMS) are experimentally examined as a basic research for the development of structural insulation concrete. As the results of this experiment, in the case of concrete mixed with HMS, the value of slump has been reduced, so it is found that the dosage of superplasticizer should be increased. As the replacement ratio of HMS increases, it has shown that the compressive strength is somewhat decreased due to the low interfacial adhesion strength of HMS. But the thermal conductivity is found to be greatly improved with the replacement ratio of HMS increases, the thermal conductivity of HMS shows the lower value of 68% at lightweight aggregate concrete and 32% of normal concrete. Also it is found that the compressive strength is decreased and thermal conductivity is increased as the water-cement ratio increases. The most outstanding for insulation performance is observed when using 20% of HMS and 50% of water-cement ratio.