• 한국전자통신학회논문지
• /
• 제12권5호
• /
• pp.791-796
• /
• 2017

본 연구에서는 DRAM 커패시터의 유전막 박막화를 위한 Load Lock(L/L) LPCVD 시스템을 이용한 적층형 커패시터의 제조 공정이 셀 커패시턴스에 미치는 영향을 조사하였다. 그 결과 기존의 non-L/L 장치에 비하여 약 $6{\AA}$의 산화막 유효두께를 낮춤으로 커패시턴스로 환산 시 약 3-4 fF의 차이가 나타남을 확인할 수 있었다. 또한 절연막으로써 질화막 두께의 측정 범위가 정상적인 관리 범위의 분포임에도 불구하고 Cs는 계산치보다 약 3~6 fF 정도 낮은 것으로 확인되었다. 이는 node poly FI CD가 spec 상한치로 관리되어 셀 표면적의 감소를 초래하였고 이는 약 2fF의 Cs 저하를 나타내었다. 따라서 안정적인 Cs의 확보를 위해서는 절연막의 두께 및 CD 관리를 spec 중심값의 10 % 이내로 관리할 필요가 있음을 확인하였다.

• 한국자동차공학회논문집
• /
• 제25권3호
• /
• pp.287-296
• /
• 2017

Although emission regulations have been gradually strengthened in the past decade, the road transport section remains the most important source of NOx emission in air pollution. One reason is that there has been an increase in the proportion of diesel vehicles and in the volume of traffic. In addition, the certification procedure for standard emission limit does not sufficiently reflect real traffic condition and various driving patterns. Therefore, the European Commission(EC) has recently come up with the RDE-LDV(Real driving emissions-light duty vehicle) regulations, and the Ministry of Environment in Korea has been conducting research on evaluating RDE-LDV with PEMS(Portable Emission Measurement Systems). According to the trip requirements of the 2nd RDE package announced by the EC, the objectives of the present study include the development of Korean RDE routes to reflect domestic traffic and road conditions. Based on the results, both RDE routes are in correct compliance with RDE-LDV regulations, including trip requirements and trip dynamics. KOR-NIER Route 1, in particular, has a higher driving load in rural driving with regard to excessive gradient of elevation compared to KOR-NIER Route 2, including relatively plane rural driving.

• 한국환경보건학회지
• /
• 제32권2호
• /
• pp.103-110
• /
• 2006

The present study is designed to analyze reliability and validity of the instruments used to measure job stress of radiological technologists mainly by means of the questionnaires from 'Korean edition of NIOSH check list'. The subjects of this study are 890 radiological technologists active at 44 general hospitals in 16 provinces and cities across the country. The item-total reliability revealed that 10 factors in 6 are the major causes of stress in job life of radiological technologists. The measuring instrument proved to be valid with reliability coefficient of internal consistency by factors being more than 0.7. The factors found to be applicable herewith include limit and authority of job (0.73), cohesion within departments (0.86), resources control (0.81), mental requirements (0.85), job load (0.82), and job stability (0.72). When job autonomy item of causes are modified for proper use to radiological technologists, the measuring instruments are expected to show high reliability. It seems, however, necessary to develop a measuring instrument to analyze and use the validity of related measuring instruments since the reliability here was rated low, with statistical coefficients lower than 0.7 in such factors as job management (0.57), conflicts within departments (-1.13), sense of responsibility for patients (0.66) and usage of education (0.26). As this study was intended to examine reliability and validity of the concepts related to measurement of job stress on the part of radiological technologists, it nay not be proper to apply the results of this study to general use, but is advised to utilize them as basis for developing instruments to verify reliability and validity by comparing with and analyzing other measuring instruments.

• 플랜트 저널
• /
• 제12권4호
• /
• pp.37-43
• /
• 2016

원자력발전소의 사고 대처 부하에 전력을 공급하는 전원계통은 다양한 조건에서도 일정 전압이 유지됨을 분석을 통하여 입증한다. 이를 위하여 발전소를 일정부하 운전 상태로 유지하고, 대용량 전동기(원자로냉각재펌프(RCP), 기기냉각수펌프(CCWP))를 각각 기동하여 기동 전 후 안전관련 모선의 전압을 측정하였다. 현장 시험으로 확보된 자료(예, 전압, 전류, 역율 등)는 기존 전력계통해석 모델의 운전 조건으로 재입력하고 재분석을 수행하였다. 이는, 기존 전력계통분석에 사용된 분석기법과 가정들을 실질적인 측정과 결과 분석으로 입증하는 과정이다. 결국, 두 경우의 전압 강하는 발전소 안전에 중요한 기기의 전압이 허용전압 이하로 저하되지 않음과 두 값의 비교 결과가 요구되는 제한치 이내임을 검증한다.

• Advances in concrete construction
• /
• 제7권2호
• /
• pp.117-126
• /
• 2019

When designing reinforced concrete (RC) members, the rebar is assumed to resist all tensile forces, but the resistance of the concrete in the tension area is neglected. However, concrete can also resist tensile forces and increase the tensile stiffness of RC members, which is called the tension stiffening effect (TSE). Therefore, this study assessed the TSE, particularly after yielding of the steel bars and the effects of the steel ratio on the TSE. For this purpose, RC member specimens with steel ratios of 2.87%, 0.99%, and 0.59% were fabricated for uniaxial tensile tests. A vision-based non-contact measurement system was used to measure the behavior of the specimens. The cracks on the specimen at the stabilized cracking stage and the fracture stage were measured with the image analysis method. The results show that the number of cracks increases as the steel ratio increases. The reductions of the limit state and fracture strains were dependent on the ratio of the rebar. As the steel ratio decreased, the strain after yielding of the RC members significantly decreased. Therefore, the overall ductility of the RC member is reduced with decreasing steel ratio. The yielding plateau and ultimate load of the RC members obtained from the proposed equations showed very good agreement with those of the experiments. Finally, the image analysis method was possible to allow flexibility in expand the measurement points and targets to determine the strains and crack widths of the specimens.

• 드라이브 ㆍ 컨트롤
• /
• 제20권3호
• /
• pp.15-24
• /
• 2023

The aim of this study was to measure and evaluate the exhaust emission factors of agricultural tractors. Engine characteristics and three exhaust emissions (CO, NO_x, PM) were collected under actual agricultural operating conditions. Experiments were performed on idling, driving, plow tillage, and rotary tillage. The load factor (LF) was calculated using the collected engine data, and the emission factor was analyzed using the LF and exhaust emissions. The engine characteristics and exhaust emissions were significantly different for each working condition, and in particular, the LF was significantly different from the currently applied 0.48 LF. The data distribution of exhaust emissions was different depending on the engine speed. In some conditions, the emission factor was higher than the exhaust emission standards. However, since most emission limit standards are values calculated using an engine dynamometer, even if the emission factor measured under actual working conditions is higher, it cannot be regarded as wrong. It is expected that the results of this study can be used for the inventory construction of a calculation for domestic agricultural machinery emissions in the future.

• 해양환경안전학회지
• /
• 제28권6호
• /
• pp.1063-1069
• /
• 2022

국내 대기오염물질 배출량 통계에 따르면 상당한 대기오염물질이 선박에 의해 발생하고 있다. 따라서 선박으로부터의 대기오염물질 배출 제한과 항만지역 대기질 개선을 위해 다양한 정책들이 시행되고 있고, 국제적으로도 선박에 의한 해양오염 방지를 위해 국제 협약 등이 이루어지고 있다. 하지만 실제 운항하는 선박에서 배출되는 대기오염물질 측정에 관한 연구와 실험은 거의 이루어지고 있지 않아, 본 연구는 이동식배출가스측정장비(PEMS)를 사용하여 실제 운항하는 9,169톤급 선박에서 발생하는 대기오염물질 배출량 평가에 대한 방법과 가능성을 제시하였다. RPM과 부하에 따라 배출량의 차이가 있었으며, NO_X 배출량은 497-2,060ppm, CO₂는 1.55-6.9%, CO는 0.002-0.14% 수준이다. 엔진 제조사에서 제공하는 Shop Test에 명시된 배출량과 실제 측정된 배출량에 차이가 있음을 확인하였다. 대상선박의 전 항해구간에서 발생하는 각 대기오염물질 최대 배출량이 PEMS 측정 구간에 포함되는 것을 확인하여, 총톤수 10,000톤급 이내 선박에 PEMS 활용 가능성을 검증하였다.

• Structural Engineering and Mechanics
• /
• 제24권6호
• /
• pp.709-725
• /
• 2006

In this paper the buckling and post-buckling behavior of slender bars under self-weight are studied. In order to study the post-buckling behavior of the bar, a geometrically exact formulation for the non-linear analysis of uni-directional structural elements is presented, considering arbitrary load distribution and boundary conditions. From this formulation one obtains a set of first-order coupled nonlinear equations which, together with the boundary conditions at the bar ends, form a two-point boundary value problem. This problem is solved by the simultaneous use of the Runge-Kutta integration scheme and the Newton-Raphson method. By virtue of a continuation algorithm, accurate solutions can be obtained for a variety of stability problems exhibiting either limit point or bifurcational-type buckling. Using this formulation, a detailed parametric analysis is conducted in order to study the buckling and post-buckling behavior of slender bars under self-weight, including the influence of boundary conditions on the stability and large deflection behavior of the bar. In order to evaluate the quality and accuracy of the results, an experimental analysis was conducted considering a clamped-free thin-walled metal bar. As this kind of structure presents a high index of slenderness, its answers could be affected by the introduction of conventional sensors. In this paper, an experimental methodology was developed, allowing the measurement of static or dynamic displacements without making contact with the structure, using digital image processing techniques. The proposed experimental procedure can be used to a wide class of problems involving large deflections and deformations. The experimental buckling and post-buckling behavior compared favorably with the theoretical and numerical results.

• International Journal of Computer Science & Network Security
• /
• 제24권1호
• /
• pp.226-234
• /
• 2024

The frequent handover problem and playing ping-pong effects in 5G (5th Generation) ultra-dense networking cannot be effectively resolved by the conventional handover decision methods, which rely on the handover thresholds and measurement reports. For instance, millimetre-wave LANs, broadband remote association techniques, and 5G/6G organizations are instances of group of people yet to come frameworks that request greater security, lower idleness, and dependable principles and correspondence limit. One of the critical parts of 5G and 6G innovation is believed to be successful blockage the board. With further developed help quality, it empowers administrator to run many systems administration recreations on a solitary association. To guarantee load adjusting, forestall network cut disappointment, and give substitute cuts in case of blockage or cut frustration, a modern pursuing choices framework to deal with showing up network information is require. Our goal is to balance the strain on BSs while optimizing the value of the information that is transferred from satellites to BSs. Nevertheless, due to their irregular flight characteristic, some satellites frequently cannot establish a connection with Base Stations (BSs), which further complicates the joint satellite-BS connection and channel allocation. SF redistribution techniques based on Deep Reinforcement Learning (DRL) have been devised, taking into account the randomness of the data received by the terminal. In order to predict the best capacity improvements in the wireless instruments of 5G and 6G IoT networks, a hybrid algorithm for deep learning is being used in this study. To control the level of congestion within a 5G/6G network, the suggested approach is put into effect to a training set. With 0.933 accuracy and 0.067 miss rate, the suggested method produced encouraging results.

• 한국산학기술학회논문지
• /
• 제18권10호
• /
• pp.739-744
• /
• 2017

탄성변형과 피로손상은 카트의 주행성능에 영향을 미치는 것으로 카트 프레임에 영구변형을 유발할 수 있다. 카트프레임은 현가장치와 다른 장치를 포함하지 않으므로 두 가지 변형에 결정적인 영향을 미칠 수 있는 코너주행 시 동적 거동은 비틀림 변형이 원인이 된다. 선회주행 시 카트의 동적 거동을 분석하기 위해 카트의 GPS추적이 실시간으로 이루어지고 카트 프레임에 작용하는 비틀림 응력값을 측정하였다. 레저카트와 레이싱카트의 재료물성치들은 인장실험을 통해 얻었다. 비틀림 응력집중과 프레임 변형은 얻어진 결과 값을 토대로 프레임의 응력해석을 통하여 파악하였다. 개발된 주행분석장치를 이용하여 레저카트와 레이싱카트를 각 조건별로 실차실험을 수행하였고 이를 통한 코너에서 카트의 주행거동을 살펴보았다. 카트가 곡선주행 시 원심력으로 인해 하중이동이 발생하였으며 카트프레임에 비틀림 응력이 발생하였다. 예를 들어 레저카드의 경우, 40 km/h의 속도로 운전할 때 최대 비틀림 피로한도를 측정한 최대 비틀림응력은 230 MPa이며 비틀림 피로한도계수는 0.65를 나타내었다. 뿐만 아니라 카트의 선회 시 운전요소들을 운전측정시스템을 인스톨한 실측장비에서 측정하였으며 카트의 운전거동은 수직변위에 의해 측정하였다.