본 연구의 목적은 모래와 타이어칩 혼합토의 반복하중조건 전후 공학적 특성 변화를 파악하는 것이다. 반복하중 시, 시료에 함유된 타이어칩 함량 및 모래와 타이어칩 입자 간의 크기비에 따른 최대전단탄성계수의 변화를 정량화 하고자, 전체 중량 대비 타이어칩 중량을 0, 10, 20, 40, 60, 100%로 하여 시료를 조성하였으며, 타이어칩 평균입경 대비 모래의 평균입경(입자크기비)을 0.44, 1.27, 1.87, 4.00으로 설정하여 혼합토를 조성하였다. 초기 상대밀도 50%의 시료를 floating wall 형태의 몰드에 조성 후, 공기압 축기(air compressor), 압력 패널(pressure panel) 및 뉴메틱 밸브(pneumatic valve)를 이용하여 정하중 재하(=50kPa), 반복하중 재하(=50-150kPa), 정하중 재하(=400kPa) 및 제하 순으로 실험이 이루어 졌다. 위의 실험이 진행됨에 따라 시료의 침하량과 전단파속도를 측정하였다. 시험 결과, 모래-타이어칩 혼합토에 가해지는 반복하중은 시료를 이루는 입자 간 접촉을 타이어칩-타이어칩 또는 타이어칩-모래에서 모래-타이어칩 또는 모래-모래로 전환시켰으며, 이로 인해 타이어칩 함량 40%에서 가장 큰 최대전단탄성계수의 증가를 확인하였다. 또한 입자크기비가 감소함에 따라 동일 타이어칩 함량에서 반복하중 시 최대전단탄성계수 증가량은 증가하였다.
The objective of this study is to predict the nonlinear behavior of reinforced concrete shear walls, with the reinforcement uniformly distributed, under reversed cyclic loads. This study introduces joint Element Model which formulates the pulling out of rebars, slipping and intrusion of junction planes. The applicability of this study was experimental verfied by specimens SW1, SW2 and SW3 tested by authors, Wall1 by Paulay, SW16 and SW19 by Sheu. In almost specimen, the ratio of analytical to experimental maximum shear stress is within approximately 5%. In case of energy dissipation and maximum drift, the analytical results fully coincide with those of experiment.
Earthquakes not only produce additional load on the structures and underlying soil, but also change the strength characteristics of the soil. Therefore, in order to analyze soil structures for stability, the behaviour after earthquake must be considered. In this paper, a series of cyclic triaxial tests and monotonic triaxial tests were carried out to investigate the undrained shear strength and liquefaction strength characteristics of Nak-Dong River sand soils which were subjected to cyclic loading. The sample was consolidated in the first stage and then subjected to stress controlled cyclic loading with 0.1Hz. After the cyclic loading, the cyclic-induced excess pore water pressure was dissipated by opening the drainage valve and the sample was reconsolidated to the initial effective mean principal stress(p/sub c/'). After reconsolidation, the monotonic loading or cyclic loading were applied to the specimen. In the results, the undrained shear strength and liquefaction strength characteristics depended on the pore pressure ratio(Ur=U/p/sub c/'). The volume change following reconsolidation can be a function of cyclic-induced excess pore water pressure and the maximum double amplitude of axial strain.
Ball screws are commonly used in linear motion feeding systems of various machine tools and automated systems. They are known to have relatively little backlash, high precision and efficiency compared to ordinary lead screws. Furthermore, the effectiveness of ball screw has made it the preferred choice of many newly developed high speed precision feeding units. The motivation of this work is to establish the groove edsigh basis of ball screws for the reduction of contact fatigue failure. In most instances, fatigue failure between ball and shaft groove is due to excessive contact pressure. Especially, the excessive load is causative of plastic flow below the contact surface, which can contribute to surface failure. But, in spite of small load, if groove conformity rate is large, contact pressure is increased and internal shear stress reach the yield value of the material. In such a point, the authors deal with design procedure for deciding the permissible conformity rate of a ball screw groove with the computational evaluation of contact pressure and maximum shear stress.
본 연구에서는 직선 개수로 내에 설치된 수제 모형 주위에서 발생하는 난류 흐름의 특성을 알아보기 위하여 수리모형실험을 수행하였다. 실험은 Froude 수가 0.100과 0.185인 두 가지 흐름 조건에서 이루어졌다. 시간평균유속과 난류 응력을 구하기 위하여 초음파 유속계를 이용하여 3차원 순간 유속을 측정하였다. 실험 결과, 수제 하류에서 난류 응력이 큰 재순환 영역이 존재하는 것으로 확인하였다. Froude 수가 큰 경우와 작은 경우의 전반적인 평균 유속 분포는 유사하게 나타났으나, 최대 무차원 난류 응력과 최대 무차원 바닥 전단응력은 Froude 수가 증가할수록 차이를 보였다.
Stainless steel sheets are commonly used for vehicles such as the bus and the train. These are mainly fabricated by spot-welding. By the way, its fatigue strength is lower than base metal due to high stress concentration at the nugget. edge of the spot-welding. By the way, its fatigue strength is lower than base metal due to high stress concentration at the nugget edge of the spot-welding point. Especially, it is influenced by welding conditions as well as geometrical factors of spot welded joint. Therefore, it is not too much to say that structural rigidity and strength of spot-welded structures is decided by fatigue strength of spot welded lap joint. Thus, it is necessary to establish a reasonable and systematic long life design criterion for the spot-welded structure. In this study, numerical stress analysis was performed by using 3-dimensional finite element model on IB-type spot-welded lap joint of 304 stainless steel sheet under tension-shear load. Fatigue tests were also conducted on them having various thickness, joint angle, lapped length, and width of the plate. From the results, it was found that fatigue strength of IB-type spot-welded lap joints was influenced by its geometrical factors, however, could be systematically rearranged by maximum principal stress ({TEX}$σ_{1max}${/TEX}) at the nugget edge of the spot-welding point.
굵은 자갈 이상의 대입경 입자를 포함하는 조립질 지반재료는 댐, 제방, 철도 등 대형 지반구조물의 성토 및 채움재료로 널리 사용되며, 이러한 구조물의 동적 해석을 위해서는 축조재료의 변형특성에 대한 엄밀한 평가가 필수적이다. 본 연구에서는 대입경 조립재료의 동적 변형특성 평가를 위하여 지름 200mm, 높이 400mm의 공시체에 대한 시험이 가능하도록 개발된 대형 공진주시험기를 활용하여 댐 축조용 사력재의 최대전단탄성계수, 전단탄성계수감소곡선 및 감쇠비를 평가하였으며, 재료의 최대입경과 균등계수와 같은 입도분포특성이 재료의 변형특성에 미치는 영향을 확인하였다. 재료의 입경이 동적 변형특성에 미치는 영향을 평가한 결과, 동일한 균등계수에서 평균입경의 범위에 따른 전단탄성계수감소곡선에 차이가 발생함을 확인하였다. 동일한 최대입경에 대하여 균등계수를 달리하는 경우 균등계수에 따라 최대전단탄성계수의 구속압 영향계수가 증가함을 확인하였다. 결과적으로 조립재료의 입도 특성 중 최대입경은 전단탄성계수감소곡선을, 균등계수는 미소변형영역의 구속압 영향계수에 대한 영향요소임을 확인하였으며, 조립재료의 동적 변형특성을 엄밀히 평가하기 위한 대형 공진주시험기의 효용성을 확인하였다.
벤더엘리먼트가 장착된 삼축압축시험장비를 이용하여 모래에 대한 일련의 압밀배수시험을 수행하였다. 상대밀도 및 유효구속응력 조건을 달리하여 각각의 조건별 응력-변형률 관계를 측정하였으며, 압밀이 종료된 시점에서의 전단파 속도를 측정함으로써 전단파 속도와 간극비, 유효응력, 그리고 전단강도와의 상관관계를 분석하였다. 분석 결과, 미소변형률에서의 전단파 속도로부터 계산된 최대전단탄성계수와 파괴 시의 축응력과 압밀 시의 구속응력의 합으로 정의되는 유효수직응력간에는 고유한 상관관계가 존재하는 것으로 나타났다. 도출된 전단탄성계수와 유효수직응력간의 상관관계는 유효구속응력을 정규화시킴으로써 정확도를 향상시켰다. 본 연구를 통해 제시된 상관관계를 통해 전단강도 및 내부 마찰각을 예측하였을 시, 실제 실내 시험을 통해 산출된 내부 마찰각을 정확하게 예측할 수 있는 것으로 나타났다. 이는 미소변형률에서의 전단파 속도를 기반으로 신뢰성 높은 파괴 시 전단강도, 나아가 내부 마찰각까지 예측이 가능하다는 것을 의미하며 기존 SPT-N value와 경험식을 통해 내부 마찰각을 예측하여 설계에 적용하는 방식의 불확실성을 개선해 줄 수 있는 매우 유용한 방법이라고 판단된다.
Because welding residual stress is formidable result in electric resistance spot welding process, and it detrimentally affect to fatigue crack initiation and growth at nugget edge of spot welded la p joints, it should be considered in fatigue analysis. Thus, accurate prediction of residual stress is very important. In this study, nonlinear finite element analysis on welding residual stress generated in process of the spot welding was conducted, and their results were compared with experimental data measured by X-ray diffraction method. By using their results, the maximum principal stress considered welding residual stress at nugget edge of the spot welded lap joint subjected to tension-shear load was calculated by superposition method. And, the $\Delta$P- $N_f$ relations obtained through fatigue, tests on the IB-type spot welded lap joints was systematically rearranged with the maximum principal stress considered welding residual stress. From the results, it was found th2at fatigue strength of the IB-type spot welded lap joints could be systematically and more reasonably rearranged by the maximum principal stress($\sigma$1max-res considered welding residual stress at nugget edge of the spot welding point.
본 선회다짐기는 도로 현장에서 가장 많이 사용하는 다짐 롤러의 다짐 특성을 반영하기 위해 개발된 실내 다짐장비이다. 기존의 충격을 이용한 프록터 다짐과는 달리 압축력과 회전을 통한 전단력을 이용한 현장 롤러의 다짐특성을 모사하였다. 본 연구의 목적은 기존의 프록터 다짐과정에서 얻기 힘든 전단응력 및 다짐중의 밀도변화 특성 등을 선회다짐기를 이용하여 평가하고, 이를 도로설계에 반영할 수 있는 기초자료로 활용하는 것이다. 이러한 선회다짐기를 이용하여 도로 현장 및 지하매설물 시공 시 가장 많이 사용되는 모래 및 노상토의 다짐 특성을 분석 및 평가하였다. 선회다짐기를 이용한 다짐 특성은 기본적으로 선회다짐 횟수와 시편의 높이, 다짐밀도, 간극비, 포화도 및 전단응력이다. 선회다짐 횟수가 증가할수록 시편의 높이는 작아지고, 간극비는 작아지고, 다짐 밀도는 증가하고, 포화도는 증가하며, 전단응력은 커지는 경향을 보였다. 전단응력은 다짐 초기에 200kPa 수준에서 시작하여 선회다짐 횟수 50회 정도가 되면 대략 330-350 kPa 수준으로 증가하였다. 동일한 시편의 경우 함수비가 커짐에 따라 다짐 밀도, 포화도 및 전단응력이 증가하는 경향을 보였다. 선회다짐기를 이용한 다짐은 밀도 및 전단응력 등 도로 설계 시 필요한 물성을 측정할 수 있는 장점을 가지고 있어 이를 도로설계시 반영한다면 더 공학적인 도로설계를 할 수 있을 것이다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.