• 한국지반신소재학회논문집
• /
• 제21권3호
• /
• pp.61-69
• /
• 2022

본 연구에서는 지반조건을 고려한 말둑의 인발저항 성능의 합리적인 평가방법 확립의 일환으로써, 지반의 세립분 함유율 및 구속압 조건에 따른 말뚝과 지반 경계면의 전단특성을 평가하기 위한 대형직접전단시험을 수행하였다. 그 결과, 수직하중이 증가하고 모형지반의 세립분 함유율이 작을수록 전단변형에 따른 전단응력이 크게 발생됨을 알 수 있었다. 그리고 동일한 수직하중과 세립분 함유율 조건에서 말뚝 모형체의 표면이 거칠수록 최대전단응력은 다소 크게 나타났다. 강도정수로써 내부 마찰각과 점착력을 산정하여 분석한 결과, 모형지반의 세립분 함유율이 증가할수록 모형체 경계면에서의 내부마찰각은 감소하였으나 점착력은 증가하는 것을 알 수 있었다. 또한, 말뚝 모형체 표면이 거칠수록 모형지반의 세립분 함유율에 관계 없이 내부마찰각과 점착력은 크게 나타났다.

• 한국환경복원기술학회지
• /
• 제5권4호
• /
• pp.19-30
• /
• 2002

The stability of slope using root-pile like to the reinforcements is affected by the interaction behavior mechanism of soil-reinforcements. Through the studying on the interaction in joint of its, therefore, the control roles can be find out in installed slope. In study, the stress level ratio based on the insert angle of installed reinforcements in soil used to numerical analysis, which was results from the duty direct shear test in Lab. The maximum shear strain variation on the reinforcements was observed at insert angle, which was approximately similar to the calculated angle based on the equation proposed by the Jewell. The elasto-plastic joint model on the contact area of soil-reinforcements was presumed, the reinforced soil assumed non-linear elastic model and the reinforcements supposed elastic model, respectively. The finite element analysis of assumed models was performed. The shear strain variation of non-reinforced state obtained by the FEM analysis including elasto-plastic joint elements were shown the rationality of general limit equilibrium analysis for the slope failure mode on driving zone and resistance zone, which based on the stress level step according to failure ratio. Through the variation of shear strain for the variation of inserting angle of reinforcements, the different mechanism on the bending and the shear resistance of reinforcements was shown fair possibility.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2004년도 학술대회지
• /
• pp.261-268
• /
• 2004

For cam and roller-follower contacting surfaces, the effect of tangential loading on the subsurface stress field at an elaso-hydrodynamic lubrication condition has been studied numerically. As tangential load increases, the subsurface stress field extended more widely to the direction of the tangential load. The positions of the maximum shear stress and the maximum effective stress are getting closer to the surface with the increasing tangential load. The tangential load at the elasto-hydrodynamic lubrication condition is of little consequence to the subsurface stress field.

• 대한토목학회논문집
• /
• 제28권1C호
• /
• pp.53-62
• /
• 2008

본 논문에서는 직접단순전단변형으로 발생하는 주응력 방향의 회전에 의한 소성변형을 고려할 수 있는 구성모델을 제안하였다. 이 모델은 두 개의 응력면에서 발생하는 응력상태의 변화를 이용하여 각 응력면의 소성변형률을 계산하였다. 두 개의 응력면에서 계산된 소성변형률을 합산하여 전체 소성변형률을 구하였다. 첫번째 응력면은 최대전단응력면을 나타내며 이 응력면은 응력변화에 따라 수평방향을 기준으로 회전한다. 두번째 응력면은 수평방향으로 고정된 수평면을 나타낸다. 초기 수직응력과 수평응력이 서로 다른 상태에 있는 직접단순전단시험의 공시체에서 전단변형으로 발생하는 주응력 방향의 회전현상을 두번째 응력면에 작용하는 응력상태를 이용하여 모델링하였다. 본 모델의 구성관계식은 전단변형으로 인한 흙의 골격변화 즉 체적변화를 수식화하였으며 응력-물의 상관관계를 동시에 묘사할 수 있는 FLAC을 이용하여 모델링하였다. 느슨한 Fraser River 모래의 배수 직접단순전단시험에서 발생하는 전단응력과 체적변화는 주응력 방향의 회전에 따른 소성변형을 포함하고 있으므로 이를 계산하여 구성모델을 검증하였다. 느슨한 모래 지반에 놓인 강성기초의 하중 증가에 따라 발생하는 지반침하를 주응력 방향의 회전을 고려하여 예측하였을 때 실제 계측된 침하량과 유사한 결과를 얻었다. 주응력 방향의 회전을 고려하지 않고 Mohr-Coulomb모델을 이용하여 계산된 침하량은 실제 침하량 또는 제안된 모델이 예측한 침하량의 약 20%정도에 해당하였다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 추계학술대회 논문집
• /
• pp.333-336
• /
• 2008

The groove rolling is a process that transforms the bloom or billet into a shape with circular section through a series of rolling. Inhibition of surface defect generation in groove rolling is a matter of great importance and therefore many research groups proposed a lot of models to find the location of surface defect initiation. In this study, we propose a model for maximum shear stress ratio over equivalent strain to catch the location of surface defect onset. This model is coupled with element removing method and applied to box groove rolling of POSCO No. 3 Rod Mill. Results show that proposed model in this study can find the location of surface defect initiation during groove rolling when finite element analysis results is compared with experiments. The proposed criterion has been applied successfully to design roll grooves which inhibits the generation of surface defect.

• Journal of Advanced Marine Engineering and Technology
• /
• 제18권3호
• /
• pp.17-25
• /
• 1994

Fully developed turbulent flow through three concentric annuli with both the rough inner and outer walls was experimentally investigated for a Reynolds number range Re = 15, 000 - 85, 000. Measurements were carried out for the pressure drop, the positions of zero shear stress and maximum velocity, and the velocity distributions in annuli of radius ratios, ${\alpha}$=0.26, 0.4 and 0.56, respectively. The experimental results showed that the positions of zero shear stress and maximum velocity were only weakly dependent on the Reynolds number.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.607-610
• /
• 2002

As machines become smaller and faster multileaf foil bearings are used to overcome the problems with heat, friction and wear Systems with foil bearings do not need a separate system for lubrication. These bearings are self acting and are therefore green systems. Until now, there have been many studies on the structural and dynamical performances. Therefore the object of the present study is to predict the flow and structural characteristics by using the Fluid/structure interaction method. The increase in RPM led to the increase in pressure, temperature difference, maximum velocity, Mach number, shear stress and torque. In the case of 90,000 RPM effects such as choking led to a non-lineararity in the system. Also the effect of eccentricity ratio was observed and showed that eccentricity increased the maximum pressure and the density difference while decreasing the shear stress and torque.

• 소성∙가공
• /
• 제17권8호
• /
• pp.607-612
• /
• 2008

The groove rolling is a process that transforms the bloom or billet into a shape with circular section through a series of rolling. Inhibition of surface defect generation in groove rolling is a matter of great importance and therefore many research groups proposed a lot of models to find the location of surface defect initiation. In this study, we propose a model for maximum shear stress ratio over equivalent strain to catch the location of surface defect onset. This model is coupled with element removing method and applied to box groove rolling of POSCO No.3 Rod Mill. Results show that proposed model in this study can find the location of surface defect initiation during groove rolling when finite element analysis results is compared with experiments. The proposed criterion has been applied successfully to design roll grooves which inhibit the generation of surface defect.

• Computers and Concrete
• /
• 제24권2호
• /
• pp.173-183
• /
• 2019

This study presents experimental and numerical results of prestressed concrete composite beams with different casting and stressing sequence. The beams were tested under three-point bending and it was found that prestressed concrete composite beams could not achieve monolith behavior due to interface slippage between two layers. The initial stress distribution due to different construction sequence has little effect on the maximum load of composite beams. The multi-step FE analyses could simulate different casting and stressing sequence thus correctly capturing the initial stress distribution induced by staged construction. Three contact algorithms were considered for interaction between concrete layers in the FE models namely tie constraint, cohesive contact and surface-to-surface contact. It was found that both cohesive contact and surface-to-surface contact could simulate the interface slip even though each algorithm considers different shear transfer mechanism. The use of surface-to-surface contact for beams with more than 2 layers of concrete is not recommended as it underestimates the maximum load in this study.

• 한국안전학회지
• /
• 제26권4호
• /
• pp.1-6
• /
• 2011

New methods for joining sheet of metal are being sought. One of the most promising methods is MPJ (mechanical press joining). It has been used in thin metal work because of its simple process and relative advantages over other methods, as it requires no fasteners such as bolts or rivets, consumes less energy than welding, and produces less ecological problems than adhesive methods. In this study, the joining process and static behavior of single overlap joints has been investigated. During fixed die type joining process for SPCC plates, the optimal applied punching force was found. The maximum tensile-shear strength of the specimen produced at the optimal punching force was 1.75 kN. The FEM analysis result on the tensile-shear specimen showed the maximum von-Mises stress of 373 MPa under the applied load of 1.7 kN, which is very close to the maximum tensile strength of the SPCC sheet(= 382 MPa). This suggests that the FEM analysis is capable of predicting the maximum tensile load of the joint.