• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 봄 학술발표회논문집(II)
• /
• pp.567-572
• /
• 1998

Structural behavior of R/C deep beams was investigated and compared to those of specimens with CFRP Grids. Test results show that the crushing of compression strut for the unstrengthened R/C deep beams is changed to the group of several diagonal cracks at mid-depth within the sheat span. Strengthened specimens grow to be more ductile after the redistribution of internal force on the CFRP Grids. The failure mode and variations of strains in the specimens are dependent on the shear span-to-depth ratio. The lower the shear span-to-depth ratio, the bigger failure load and the less variations in strain are observed. Additional anchorage of CFRP Grids does not only cause the improvement in the internal resistance, but also control the brittle shear failure of specimen after reaching the maximum loads.

• Structural Engineering and Mechanics
• /
• 제74권2호
• /
• pp.267-282
• /
• 2020

The seismic performance and failure modes of the dual system of moment resisting frames and thin steel plate shear walls (TSPSWs) without and with one or two outrigger trusses are studied in this paper. These structural systems were utilized to resist vertical and lateral loads of 40-storey buildings. Detailed Finite element models associated with nonlinear time history analyses were used to examine seismic capacity and plastic mechanism of the buildings. The analyses were performed under increased levels of earthquake intensities. The models with one and two outriggers showed good performance during the maximum considered earthquake (MCE), while the stress of TSPSWs in the model without outrigger reached its ultimate value under this earthquake. The best seismic capacity was in favour of the model with two outriggers, where it is found that increasing the number of outriggers not only gives more reduction in lateral displacement but also reduces stress concentration on thin steel plate shear walls at outrigger floors, which caused the early failure of TSPSWs in model with one outrigger.

• 한국정밀공학회지
• /
• 제23권8호
• /
• pp.127-136
• /
• 2006

Metallic sandwich plates with inner dimpled shell subject to 3-point bending have been analyzed and then optimized for minimum weight. Inner dimpled shells can be easily fabricated by press or roll with high precision and bonded with same material skin sheets by resistance welding or adhesive bonding. Metallic sandwich plates with inner dimpled shell structure can be optimally designed for minimum weight subject to prescribed combination of bending and transverse shear loads. Fundamental findings for lightweight design are presented through constrained optimization. Failure responses of sandwich plates are predicted and formulated with an assumption of narrow sandwich beam theory. Failure is attributed to four kinds of mechanisms: face yielding, face buckling, dimple buckling and dimple collapse. Optimized shape of inner dimpled shell structure is a hemispherical shell to minimize weight without failure. It is demonstrated that bending stiffness of sandwich plate is 2 or 3 times larger than solid plates with the same strength. Failure mode boundaries and iso-strength lines dependent upon the geometry and yield strain of the material are plotted with respect to geometric parameters on the failure map. Because optimal parameters of maximum strength for given material weight can be selected from the map, analytic solutions for maximum strength are expressed as a function of only material property and proposed strength. These optimal parameters match well with numerical optimal parameters.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 가을 학술발표회 논문집
• /
• pp.713-720
• /
• 2000

The directional response of strength and deformation on the rocks acting by external loads is called by strength and deformability anisotropy, respectively. Peak strength and its failure criteria of anisotro rocks have been studied and reported. Many authors have investigated in detail the behavior of triaxial peak strength of anisotropic rocks(Jaeger 1960, McLamore & Gray 1967, Hoek & Brown 1980, Ramamurthy & Rao 1985). They concluded that the triaxial strength of anisotropic rocks varies according to the inclination of discontinuity in specimens. And, the minimun triaxial strength occurs in the specmen with 60° of inclination angle ; and specimens with 0° or 90° inclination have maximum triaxial strength. Based on the experimental result, the behavior triaxial strength is investigated. The triaxial compression tests due to the angle bedding plane have been conducted and the material constants, 'm' and 's', cohesion and angle of friction and nonlinear strength parameters to fit for the failure criterion were derived from the regression analysis. And, the experimental date are employed to examine three existing failure criteria for peak strength, provided by Jaeger, McLamore and Hoek & Brown and Ramamurthy & Rao. For a shale, the suitability of the failure criteiria of triaxial peak strength for anisotropic rocks is discussed.

• 한국공간구조학회논문집
• /
• 제21권2호
• /
• pp.49-56
• /
• 2021

The damage to non-structural elements in buildings has been increasing due to earthquakes. In Korea, post-installed anchors produced overseas have been mainly used for seismic anchorage of non-structural components to structures. Recently, a new cast-in-place concrete insert anchor installed in concrete without drilling has been developed in Korea. In this paper, an experimental study was conducted to evaluate the tensile and shear strengths of the newly developed anchor under monotonic load. The failure modes of the tension specimens were divided into concrete breakout failure and steel failure, and all shear specimens showed steel failure. In both tension and shear, the maximum loads of specimens were greater than the nominal strengths predicted by the concrete design code (KDS 14 20 54). As a result, it is expected that the current code can also be used to calculate the strength of the developed cast-in anchor.

• Composites Research
• /
• 제25권1호
• /
• pp.19-25
• /
• 2012

본 연구에서는 압축하중을 받는 원공을 가진 샌드위치 복합재 기둥의 좌굴 거동을 조사하였다. 샌드위치 복합재 기둥은 유리섬유직물/에폭시 면재와 우레탄 폼 심재로 구성되어 있다. 이때 면재 두께는 1.7mm, 심재 두께는 23mm, 37mm, 48mm, 61mm, 그리고 원공 직경은 25mm와 38mm를 고려하였다. 원공 위치가 샌드위치 복합재 기둥의 좌굴 거동에 미치는 영향을 조사하기 위해 직경 25mm인 원공이 시편중앙부에 있는 경우, 시편중앙부를 기준으로 중앙부와 끝단 사이의 1/4 지점에 있는 경우, 시편중앙부를 기준으로 중앙부와 끝단 사이의 1/2 지점에 있는 경우를 고려하였다. 시편중앙부에 직경 25mm인 원공이 있는 경우의 좌굴하중과 최대하중은 원공이 없는 경우보다 10% 정도 낮게 나타나며, 시편중앙부에 직경 38mm인 원공이 있는 경우의 좌굴하중과 최대하중은 원공이 없는 경우보다 30% 정도 낮게 나타났다. 그러나 원공 위치가 좌굴하중과 최대하중에 미치는 영향은 크지 않았다. 주요 파괴 모드는 심재 두께가 23mm와 37mm와 같이 얇은 경우는 심재 전단파괴가 지배적이고 심재 두께가 48mm와 61mm와 같이 두꺼운 경우는 면재-심재 분리가 지배적으로 관찰되었다.

• Earthquakes and Structures
• /
• 제17권2호
• /
• pp.221-232
• /
• 2019

Material non-linearity of Reinforced Concrete (RC) framed structures is studied by modelling concrete using the Concrete Damage Plasticity (CDP) theory. The stress-strain data of concrete in compression is modelled using the Hsu model. The structures are analyzed using a finite element approach by modelling them in ABAQUS / CAE. Single bay single storey RC frames, designed according to Indian Standard (IS):456:2000 and IS:13920:2016 are considered for assessing their maximum load carrying capacity and failure behavior under the influence of gravity loads and lateral loads. It is found that the CDP model is effective in predicting the failure behaviors of RC frame structures. Under the influence of the lateral load, the structure designed according to IS:13920 had a higher load carrying capacity when compared with the structure designed according to IS:456. Ultra High Performance Fiber Reinforced Concrete (UHPFRC) strip is used for strengthening the columns and beam column joints of the RC frame individually against lateral loads. 10mm and 20mm thick strips are adopted for the numerical simulation of RC column and beam-column joint. Results obtained from the study indicated that UHPFRC with two different thickness strips acts as a very good strengthening material in increasing the load carrying capacity of columns and beam-column joint by more than 5%. UHPFRC also improved the performance of the RC frames against lateral loads with an increase of more than 3.5% with the two different strips adopted. 20 mm thick strip is found to be an ideal size to enhance the load carrying capacity of the columns and beam-column joints. Among the strengthening locations adopted in the study, column strengthening is found to be more efficient when compared with the beam column joint strengthening.

• 한국항공우주학회지
• /
• 제32권3호
• /
• pp.74-81
• /
• 2004

복합재 주익을 실험용 경항공기급에 적용하기 위하여, 복합재료의 특성과 제작공정을 고려한 일련의 기본 설계와 해석과정을 보이고 그 결과를 수록하였다. Schrenk 방식 (NACA TM No. 948) 과 FAR part 23 Appendix A의 근사방법을 이용하여 공력하중해석을 수행하였으며, 이에 의거한 구조하중 조건을 만족함과 동시에 복합재 구조의 장점을 반영할 수 있도록 주요 부재를 배치하였다. 제작공정과 동일한 조건에서 성형된 시편들에 대해 실험을 수행하여 선정재료의 설계기준치를 확보하였고, 단순화된 상자형 날개보에 대해 최대 변형 률 파괴기준식을 적용하여 구조의 안전도를 평가하였다.

• Geomechanics and Engineering
• /
• 제28권3호
• /
• pp.209-224
• /
• 2022

In this study, the numerical analysis model of π-beam explosion is established to compare and analyze the failure modes of the π-beam under the action of explosive loads, thus verifying the accuracy of the numerical model. Then, based on the numerical analysis of different protection forms of π beams under explosive loads, the peak pressure of π beam under different protection conditions, the law of structural energy consumption, the damage pattern of the π beam after protection, and the protection efficiency of different protective layers was studied. The testing results indicate that the pressure peak of π beam is relatively small under the combined protection of steel plate and aluminum foam, and the peak value of pressure decays quickly along the beam longitudinal. Besides, as the longitudinal distance increases, the pressure peak attenuates most heavily on the roof's explosion-facing surface. Meanwhile, the combined protective layer has a strong energy consumption capacity, the energy consumed accounts for 90% of the three parts of the π beam (concrete, steel, and protective layer). The damaged area of π beam is relatively small under the combined protection of steel plate and aluminum foam. We also calculate the protection efficiency of π beams under different protection conditions using the maximum spalling area of concrete. The results show that the protective efficiency of the combined protective layer is 45%, demonstrating a relatively good protective ability.

• 한국전산구조공학회논문집
• /
• 제27권6호
• /
• pp.625-633
• /
• 2014

본 논문에서는 액화천연가스 운송을 위해 사용되는 맴브레인형 Mark III 화물창 시스템의 주요 구조물인, 방열 판 구조물의 파손 강도 평가를 수행한 내용을 다루고 있다. Mark III 방열 판 구조물을 복합적층 구조물로 고려하였으며 상용화된 범용 유한요소 프로그램인 MSC사의 PATRAN과 MARC를 사용하여 Mark III 방열 판 구조물의 유한요소 모델을 개발하였다. 특히, 액화천연가스 화물의 특성으로 인해 Mark III 방열 판 구조물이 접하는 상온에서 극저온에 이르는 광범위한 온도 분포에 따른 재료 물성치 변화를 유한요소 모델에 포함하였다. 이 유한요소 모델을 기반으로 파손 강도 평가 절차가 확립되었으며, 이 때 Mark III 방열 판 구조물의 파손 발생 여부를 판단하기 위해 Hashin, Hill, Hoffman, maximum stress, 그리고 Tsai-Wu와 같은 이방성 파손 기준들을 사용하였다. Mark III 방열 판 구조물의 전반적인 구조적 거동을 이해하였으며 이후 초기 파손 영역에서 강도 평가를 수행하여 파손이 발생되었을 때의 위치와 하중 등을 알 수 있었다.