• 한국추진공학회지
• /
• 제2권2호
• /
• pp.47-55
• /
• 1998

중형항공기용 터보팬엔진의 설계점, 탈설계점에 대한 정상상태 및 천이상태 성능해석을 수행하였다. 정상상태 성능해석은 설계점으로 선정한 지상최대추력조건과 탈설계점으로 선정한 최대상승조건과 순항조건에서 수행하였으며 부분부하 성능해석 결과 저압압축기 회전속도 90％RPM에서 가장 연료소모율이 적어 경제적임을 확인하였다. 천이상태 성능해석은 각각의 비행조건에서 연료의 Step증가, Ramp증가, Ramp감소, Step 증가 후 Ramp 감소의 경우에 대하여 수행하였다. 천이상태의 성능해석을 위해서는 압축기와 터빈의 일에 대한 조합이 필요한데, 일의 조합방정식에 포함된 잉여 토오크의 적분에는 Modified Euler Method를 적용하였다. 천이상태 성능해석 결과, 모든 비행조건에서 Step 및 Ramp 증가의 경우 고압압축기의 터빈입구온도가 제한온도를 초과하며, 최대상승조건에서 연료를 Step 또는 5.5초 이내의 Ramp 증가시킬 경우 고압압축기에서 실속이 발생함을 확인하였다.

• 한국자동차공학회논문집
• /
• 제13권6호
• /
• pp.38-47
• /
• 2005

In this paper, a regenerative braking algorithm is proposed to make the maximum use of the regenerative braking energy for an independent front and rear motor drive parallel HEV. In the regenerative braking algorithm, the regenerative torque is determined by considering the motor capacity, motor efficiency, battery SOC, gear ratio, clutch state, engine speed and vehicle velocity. To implement the regenerative braking algorithm, HEV powertrain models including the internal combustion engine, electric motor, battery, manual transmission and the regenerative braking system are developed using MATLAB, and the regenerative braking performance is investigated by the simulator. Simulation results show that the proposed regenerative braking algorithm contributes to increasing the battery SOC, which recuperates 60 percent of the total braking energy while satisfying the design specification of the control logic. In addition, a control algorithm which limits the regenerative braking is suggested by considering the battery power capacity and dynamic response characteristics of the hydraulic control module.

• 한국소음진동공학회논문집
• /
• 제23권3호
• /
• pp.209-217
• /
• 2013

이 논문은 선박용 디젤엔진의 진동제어에 적용할 수 있는 MR 유체기반 마운트(MR 마운트)의 최적설계를 제시한다. 이 연구에서는 압착모드, 유동모드, 전단모드를 포함하는 혼합모드가 제안되었고 설계되었다. 효과적인 진동제어를 위하여 요구되는 MR 마운트의 작동 댐핑력을 결정하기 위하여 디젤엔진의 기진력이 분석되었다. 이 분석에서 V-type엔진이 고려되었으며 피스톤의 토크에서의 속도와 가스압력간의 관계를 유도하였다. 결과적으로 상업적으로 이용 가능한 MR 유체의 장의존적 유동특성과 기진력을 통합함으로써 적절한 MR 마운트의 크기가 설계되었다. 게다가 기하학적 제한조건이 고려된 최대 구동력을 얻기 위해 ANSYS를 이용하여 최적설계가 수행되었다. 자기밀도분석을 통해 바닥간격과 코일의 반지름과 같은 최적설계변수가 결정되었다.

• 동력기계공학회지
• /
• 제18권2호
• /
• pp.5-11
• /
• 2014

The purpose of this study is to investigate the specific characteristics of combustion and exhaust emissions on a 4-cylinder common rail diesel engine as EGR rate and the rate of blended bio-diesel was altered. Bio-diesel fuel which is a sort of alternative fuels can be adapted to diesel engine directly without modifying. This study was performed to 2000rpm of engine speed with torque 30Nm while EGR rate and the rate of blended bio-diesel was changed. Decreasing combustion pressure and increasing the rate of heat were occurred when we had changed the EGR rate on the 20% of bio-diesel blended diesel fuel. The maximum pressure of combustion and the IMEP became higher as the EGR rate and the rate of blended bio-diesel were changed. Exhaust gas temperature was increased the higher rate of the blended bio-diesel under the fixed EGR rate. However, it went down as the EGR rate increased. The amounts of CO and Soot were reduced with increasing the rate of the blended bio-diesel without changing EGR rate and raised with increasing of the EGR rate. On the fixed EGR rate, NOx was increased along with growing the rate of the bio-diesel. On the other hand, it was decreased while EGR rate were going up.

• 한국자동차공학회논문집
• /
• 제24권5호
• /
• pp.538-548
• /
• 2016

The purpose of this study is to identify the possibility of effective tuning works, understand the characteristics of tuning engine, and analyse the basic data of engine tuning inspection corresponding to the safe operation and environment of a driving gasoline car. The effects of tuning on the characteristics of performance and exhaust emissions under a wide range of engine speeds are experimentally investigated by the actual driving car with a four-cycle, four-cylinder DOHC, turbo-intercooler, water-cooled gasoline engine operating at four types of non-tuning, tuning 1, 2 and 3. The tuning parts in the gasoline engine are the intake manifold, intake pipe and air filter. In the experiment, the output, torque and air-fuel ratio of the five-speed automatic transmission vehicles were measured at the chassis dynamometer(Dynojet 224xLC) with one person on board. The exhaust emissions of $NO_X$, THC, CO, $O_2$ and $CO_2$, and excess air ratio(${\lambda}$) at the other chassis dynamometer(DASAN-MD-ASM-97-KR-HD) were also measured by the idle/constant-speed mode(ASM2525 mode) test method. It is found that the actual air-fuel ratios of non-tuning and tuning engines were shown to be lower than the stoichiometric air-fuel ratio with increasing engine speed, and the actual air-fuel ratio of non-tuning engine was slightly higher than those of tuning engines when the engine speed is more than 4000 rpm. The output was significantly increased by the tuning whereby the maximum output of tuning engine was more increased to approximately 117.64% than that of non-tuning engine. In addition, CO, THC and $NO_X$ emissions of non-tuning and tuning engines measured by the constant-speed test mode were all satisfied with the inspection standards. CO emission was increased, while THC and $NO_X$ emissions were reduced by tuning.

• Tribology and Lubricants
• /
• 제24권3호
• /
• pp.133-139
• /
• 2008

In recently designed diesel engines, the running conditions for piston pin bearings have become very severe due to combustion pressure and temperature increase. In this paper, it will be investigated the tendency of piston pin rotating motion by calculating the friction coefficient at piston pin bearings, the oil film thickness and the frictional torques induced by hydrodynamic shear stress. Finally, the pressure distributions on the oil film of piston pin bearings will be found by two-dimensional lubrication analysis in order to help the optimum design of the bearings of piston pin. Specially, it is investigated the effects on the film pressure distribution due to the change in maximum combustion pressure.

• 한국수소및신에너지학회논문집
• /
• 제15권2호
• /
• pp.129-136
• /
• 2004

환경문제와 석유자원의 고갈이 많은 연구자들을 기존 탄화수소연료를 대체할수 있는 재생 가능한 연료를 구하는데 많은 노력을 기울이고 있다. 수소연료는 유해배기물질이 없는 연소와 또한 연소후에 재생 가능한 물성분만 배출하는 속성으로 미래의 청정에너지로 각광을 받고 있다. 이러한 이유로 수소연료는 수송기계의 연료로도 주목을 받고 있다. 따라서 수소연료기관 개발은 21세기에도 지속적으로 진행될 것이다. 이에대한 초기연구로 기체 LPG 연료가 아닌 액체 LPG 연료를 흡기관에 분사하여 기화된 LPG 연료를 엔진으로 흡입하는 LPi엔진에 수소연료를 과급하여 엔진에 성능을 연구하고자 하였다.

• 동력기계공학회지
• /
• 제6권2호
• /
• pp.73-81
• /
• 2002

In this study, electronically controlled automatic transmission adopted on a subcompact model in the market was modelled, and the driving performances of the transmission were simulated with the models. Kinetic and dynamic models of working components are established. The driving simulation program is developed with those models, and the various driving conditions are analyzed. With the results, the dynamic behaviour of the engine and the automatic transmission is easily understood. Especially, the transient performances of torque converter and clutches are deeply analyzed. Skipping the vehicle road test by using this analyzing tool, we can expect the cost down and the reduction of the development period of automatic transmission.

• Journal of Biosystems Engineering
• /
• 제25권5호
• /
• pp.369-378
• /
• 2000

The purpose of this study is to developed high-efficient rotary tillage system for a power tiller by improving the rotary blade. A kind of the rotary blade with single-edged blade(DS) was developed that requires lower tillage energy than conventional double-edged blade(CD) on the design theory for Japanese rotary blade. In order to find out the tillage characteristics between the single-edged blade and the double-edged blade for power tiller, experiments were performed in soil-bins which were filled up clay loam, loam and sandy loam, and then analyzed the effects of the factors such as soil texture, travelling speed, rotational speed, and tillage depth to each of the blades. And field tests were carried out to compare tillage performances of the two blades using rotary cultivator driven by conventional power tiller. The results of this study were summarized as follows; 1) On the soil bin experiment, it was found that tillage torque of the single-edged blade was less than the ones of the double-edged blade. The decreasing ratios of maximum tillage torque of the single-edged blade to the ones of the double-edged blade were 1 to 8% at clay loam, 5 to 20% at loam and 9 to 31% at sandy loam, respectively. 2) By the field tests, that the tillage performances with the single-edged blade compared with the double-edged blade was improved about 19% in field capacity, about 34% in fuel consumption, and 12.5% in soil breaking ratio. Furthermore, the fluctuation of engine speed, the variation of exhaust gas temperature, and the amount of soil clogging on the blade and straw wound on the rotary shaft showed lower values with the developed blade than the conventional blade. So, it may be concluded that tillage performance by the developed single-edged blade was improved compared with the one by the conventional double-edged blade.

• 해양환경안전학회지
• /
• 제27권4호
• /
• pp.550-556
• /
• 2021

본 연구에서는 상용화된 로프절단장치 타입 중 국내에 가장 많이 도입되어있는 Scissor type을 대상으로 유한요소해석을 수행하여 다양한 로프 걸림 상황에서 안정성이 확보되는 적합한 구조 형태를 평가하였으며, 수조 실험 및 실선 실험을 통해 효용성을 검증하였다. 연구 결과, 로프 걸림에 의하여 프로펠러축이 회전하지 않을 경우 엔진에서 발생하는 지속적인 토크로 인하여 로프절단장치에 비틀림이 발생하고 유한요소 해석상 자유도가 구속되어 있지 않은 하부의 블레이드에서 가장 높은 변형이 발생하는 것을 확인하였다. 블레이드의 두께가 증가할수록 최대변형량은 줄어들고 최대응력은 낮아져 안전율이 증가하는 결과가 나타났으며, 동일한 블레이드 두께에서 토크의 변화량이 최대응력과 최대변형량에 미치는 영향은 로프절단장치의 외력이 미치는 위치와 무관하며 정비례하게 감소하는 것으로 나타났다. 해석 결과를 토대로 실시한 수조실험 및 실선실험 결과, 모든 조건과 환경에서 로프 및 어망이 원활하게 제거되는 것을 확인하였다.