• IEMEK Journal of Embedded Systems and Applications
• /
• v.7 no.5
• /
• pp.277-284
• /
• 2012

To meet the usage of discrete wavelet transform (DWT) on potable devices, this paper implements 2-level DWT using a reference many-core processor architecture and determine the optimal many-core processor. To explore the optimal many-core processor, we evaluate the impacts of a data-per-processing element ratio that is defined as the amount of data mapped directly to each processing element (PE) on system performance, energy efficiency, and area efficiency, respectively. This paper utilized five PE configurations (PEs=16, 64, 256, 1,024, and 4,096) that were implemented in 130nm CMOS technology with a 720MHz clock frequency. Experimental results indicated that maximum energy and area efficiencies were achieved at PEs=1,024. However, the system area must be limited 140mm2 and the power should not exceed 3 watts in order to implement 2-level DWT on portable devices. When we consider these restrictions, the most reasonable energy and area efficiencies were achieved at PEs=256.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1995.10a
• /
• pp.183-186
• /
• 1995

Most defects in the cement concrete pavement take place mainly on the joints. These corner cracks don't happen as often as others relatively. it happens continuously. In order to analyze the structural behavior of the corner cracks, The finite element structural analysis was performed on the representative section of the cement concrete pavements using JSLAB which uses FEM analysis method. On plain cement concrete pavements, The result shows that loading not only on the joints but also on the center of slab brings out the maximum stress on the corner of slab and it is expected to make the corner cracks.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.3
• /
• pp.130-137
• /
• 2012

Blast walls are integral structures at the typical offshore topside module to provide safety barriers for personnel and critical equipment against any blast loading and hydrocarbon explosions. The blast wall structures are usually configured with stainless steel. It can be referred as the good mechanical properties of the stainless steel against blast load, which features the characteristics of significant energy absorption and ductility. In this study, the proposed designs of corrugated panel are examined in order to determine the best design which satisfies the design criteria. The criteria on maximum deflection and stress are used to decide the best design. The effect of inclined angle of profile on deformation characteristics of blast wall is also performed. The numerical study was performed by using NX Nastran 7.5.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.18 no.2
• /
• pp.137-143
• /
• 2009

This paper presents the fabrication of inchworm motor for high precision actuator system of large displacement and high force. The inchworm motor consists of a extend actuator that provides displacement of tool guide and two clamping actuators which provide the holding force. In order to avoid the PZT fracture, design of pre-load housing was conducted by flexure hinge structure, because PZT actuator has low tensile and shear. To design the pre-load housing and optimize the clamping mechanism, the static and dynamic analysis were conducted by finite element method. From these results, a prototype of the inchworm motor was fabricated and dynamic characteristic with respect to the various frequency was tested. The maximum velocity of the inchworm motor was $41.1{\mu}m/s$ at 16Hz.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.842-847
• /
• 2001

In order to reinforce the plate in bending spot-welding method is usually used. To analyze the effect of the reinforcement of the plates spot-welded, finite element method was employed to take advantage of the deflection obtained with respect to the change of the aspect ratio and area ratio. The reinforcement effect represented by the equivalent thickness. Was maximum when the aspect ratio was around $1.2{\sim}1.6$ and the area ratio was 0.05.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.8
• /
• pp.80-87
• /
• 1996

The present paper will give some results of the fatigue behavior of typical axi-symmetric forward extrusion die. The extrusion process is analyzed by rigid-plastic FEM and the deformation analysis of extrusion die is conducted by elasto-plastic FEM. To approach the crack problem LEFM (Linear Elastic Fracture Mechanics) is introduced. Using special element in order to conside the sigularity of stress/ strain in the vicinity of the crack tip, stress intensity factor and the effective stress intensity factor is calculated. Applying proper fatigue crack propagation criterion such as Paris/Erdogan fatigue law and maximum principal criterion to these data, then, the angle and the direction of fatigue crack propagation is simulated. In result, it is proved that the simulated fatigue crack propagates in the zigzag path along the radial direction and fatigue life of the extrusion die is evaluated by using the computed crack growth rate.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.11
• /
• pp.1962-1966
• /
• 2007

Transducer for ultrasonic linear motor with the symmetric and anti-symmetric modes was studied. The ultrasonic linear motor consists of two Langevin type piezoelectric vibrators that cross at right angles with each other in tip. In order to excite symmetric and anti-symmetric resonance modes, the transducer must have a phase shift of 90 degree in space and time. Therefore, the tip of transducer moves on an elliptical motion. In this paper, the finite element analysis was used to optimize dimension and displacement of the transducer. The ultrasonic motor was fabricated using the simulated result and the driving characteristics were measured. No-load velocity was 0.28[m/s] and the maximum efficiency was 30[%] in resonance frequency.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2002.05a
• /
• pp.208-213
• /
• 2002

When a thermoset conductive adhesive joints are subjected to the thermal cycles, the thermal stresses are developed around the joints. Most of in-plane, hi-axial components of these residual stresses induces large tensile peel stresses and weakens adhesive joints. Also these stresses vary with thermal cycles, and result in thermal fatigue loading and debonding propagation. In this study, the thermal ratchetting effect in conductive adhesive joints are evaluated by the finite element analysis with the viscoelastic material model. In order to Investigate the relationship between thermal ratchetting and glass transition temperature, the mathematical material model has been developed experimentally by dynamic mechanical analysis. These material models are implemented to the finite element analysis with thermal loading cycles. And the stress profiles around the conductive adhesive joints are calculated. It has been observed that the thermal ratchetting occurs when the maximum temperature of thermal cycles is above the glass transition temperature. The peel and shear stress components increase as the thermal loading time increases. This will contributes to thermal fatigue fracture of the joints.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 1993.06a
• /
• pp.1394-1397
• /
• 1993

A Fuzzy Microprocessor(FMP) is presented, which is suitable for real-time control applications. The features include high speed inference of maximum 114K FLIPS at 20MHz system clocks, capability of up to 128-rule construction, and handing of 8 input variables with 8-bit resolution. In order to realize these features, the fuzzifier circuit and the processing element(PE) are well optimized for LSI implementation. The chip fabricated in 1.2$\mu\textrm{m}$ CMOS technology contains 71K transistors in 82.8 $\textrm{mm}^2$ die size and is packaged in 100-pin plastic QFP.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.291-294
• /
• 2005

This paper presents a method of improving performance of an electromagnetic clutch for the next generation tank gun. One of the most important things in the design of the clutch is to satisfy the requirement for the maximum torque even if the torque is varied. To achieve this requirement, it is needed to expand the operation range of the torque. Consequently, we have performed shape changes in order to cancel magnetic flux bottlenecks on the magnetic path. Simulation results from the finite element method show that the method proposed in this paper is proper for the clutch.