• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.8
• /
• pp.843-848
• /
• 2015

The objective of this study is to observe and optimize a typical ocean environment and reduce wave reflections in the wave flume. In order to generate ocean waves in the wave flume, a combination of a horizontal piston type wave generator and wave absorbers was installed in the channel. Two probes for measuring the wave heights, i.e., wave level gauges, were used to record the continuous variation of the wave surface, the phase difference, and the maximum (crest) and minimum (trough) points of the propagating waves. In order to optimize the shape and size of the propagating waves, several absorption methods were proposed. Apart from an active wave absorption method, we used methods that involved vertical porous plates, horizontal punching plates, and sloping-wall-type wave absorbers. To obtain the best propagating waves, a sloping-wall-type wave absorber was chosen and tested in terms of the constitutive filling materials and the location and shape of the plate. This study also focused on the theoretical prediction of the wave surface, separating them into the incident and reflective components. From the results, it is evident that the wave absorber comprising a hard filling material exhibits a better performance than the absorber comprising a soft material, i.e., the wave absorber can be a strong sink to control the energy of the incoming wave. In addition, larger wave absorbers correspond to lower reflectance because a larger volume can reduce the incoming wave energy. Therefore, at constant absorber conditions, the reflectance of the wave increases as the wave period increases. Finally, the reflectance of the wave was controlled to be less than 0.1 in this study so that the wave flume can be used to simulate an offshore environment.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.17 no.6
• /
• pp.580-588
• /
• 1992

Plasma-spraying was conducted to produced the microwave absorbing surface films on the alumi-num-alloy used for the fuselage to protect the aircraft against the RADAR detction. The surface films were produced by plasma-splaying the mecharucally mixed composite powders of the silicon carblde and Ni-Zn ferrite. This M /W absorbers were designed experimentally and fabricated trialty, as a result of which the rolative frequency bandwidth of 7.6 to 8.4% were obtained under the tolerance limits of the re-flection coefficients lower than -6dB(absorption ratio 75%), and the maximum absorption thickness becomes 0.5 to 0.5.imm, which Is much thinner than that of the conventional ones.

• Composites Research
• /
• v.30 no.6
• /
• pp.422-428
• /
• 2017

The moisture absorption behavior, tensile properties, and thermal analysis properties of MWCNT embedded nanocomposites exposed to temperature and moisture were evaluated. The contents of MWCNT were 0 wt%, 1 wt%, and 2 wt%, respectively. The specimens were exposed to immersed conditions at $25^{\circ}C$ and $75^{\circ}C$ for up to 600 hours. According to the results, the apparent moisture content increased as the exposure time increased, but the difference between the maximum moisture content and the moisture content at 600 hours was almost constant. The tensile modulus decreased with increasing exposure time and the degree of decrease was increased significantly as the MWCNT content and exposure temperature increased. The tensile strength decreased with longer exposure time without MWCNT, but increased with MWCNT due to the reinforcing effect of MWCNT. The storage modulus, glass transition temperature, tan d peak magnitude were low as the exposure time increased, but tan d curves with two peaks appeared when exposed to high exposure temperature for more than 300 hours.

• Journal of Biosystems Engineering
• /
• v.30 no.3 s.110
• /
• pp.147-154
• /
• 2005

The improved hitch device, which connecting the trailer to power tiller, was developed. This device, composed with spring and rubber, could reduce the vibration and shock levels during driven on off-road. The vertical vibration accelerations for the improved hitch device were measured at 6 positions, i.e. engine, hitch, seat, and three points in trailer (front, middle, and rear) for not driving but at low engine speed of 500 rpm, and compared with the existing hitch device. The results of this study could be summarized as follows; The average vibration acceleration up to 120 Hz was $0.4m/s^2$ at engine part, but it was 0.08 and $0.05m/s^2$ at trailer for existing and improved hitch device, respectively. About $38\%$ of average acceleration level could be absorbed for the improved hitch device compared with existing hitch device. The average vibration acceleration up to 40 Hz was reduced to 0.12 and $0.06m/s^2$ at trailer for existing and improved hitch device respectively, showing the reduction effect of $50\%$. The maximum acceleration occurred at up to 20 Hz of low frequency was much higher than total acceleration occurred at up to 120 Hz, which means that much loss or damage could be occurred during transporting of agricultural products on off-road. The portions of average acceleration occurred at up to 20 Hz of low frequency were $27\%\;and\;21\%$ for the existing and improved hitch device, respectively.

• Microbiology and Biotechnology Letters
• /
• v.32 no.4
• /
• pp.328-333
• /
• 2004

To treat a waste gas containing a high strength H2S, the two-stages microbial desulfurization process that conof a bioreactor immobilized with Acidithiobacillusferrooxidans and a chemical absorption scrubber has was proposed. After 4 times repeat of batch cultures, the immobilized bioreactor has been stabilized and the rate of iron oxidation reached 0.89 kg . $m^{-3}{\cdot}m^{-1}$ at steady state. The two-stages microbial desulfurization prowas able to be operated for a long term over 54 days. The removal efficiencies of H2S were 97-99% at a space velocity of 70 h-I and a inlet concentration of 37,000 ppmv. The maximum elimination capacity of H2S was approximately 3.3 kg S . $m^{-3}{\cdot}m^{-1}$. In the bioractor, the concentrations of the $Fe^{3+}$ and the immobilzed cell were constantly maintained during the desulfurization.

• Korean journal of food and cookery science
• /
• v.7 no.4
• /
• pp.71-86
• /
• 1991

This study was attempted to enhance nutritional value of cooked rice by adding milk in cooking water. Cooked and soaked rice with five different levels of milk in cooking water (0%, A: 30%, B: 50%, C: 70%, D: 100%, E) was tested for rheological parameters, fine structural changes, sensory evaluation. 1. Water absorbance of raw rice in cooking water with varying amountes of milk, was tested at $5^{\circ}C$ and $15^{\circ}C$ for 2 hours. Water absorption ratio was decreased as milk content was increased and soaking temperature was low. Time for maximum water absorption of sample A was 40 min at 1$15^{\circ}C$ but for sample B to D, it was not reached until 120 min. 2. Electronmicroscopic observation revealed that starch granules of rice lost their regular forms by soaking for 90 minutes, but recovered most of initial regularity after 24 hours. Increase in milk content of soaking water decreased marginal sharpness of the starch granule, presumably due to reduced swelling of the granule. 3. Degree of gelatinization of cooked rice was highest in sample A and progressively decreased as milk content was increased. It was, however, increased in all samples when the cooking water to rice ratio was raised from 160% to 180%. During 4 hour storage, rates of retrogradation were not different between A and B samples, but those of C, D and E were about 2.5 times higher than A and B under the optimal condition of 170% cooking water to rice ratio. This was in the order reverse to hardness order of AC>A, D＞E at cooking water to rice ratios of 160% and 170%, above which A sample surpassed the rest of samples. 4. Sensory evaluation conducted by fifteen university students as panelists showed that there were more significant differences among five samples in flavour, texture than appearance and a notable preference for b and C over A, D and E.

• Journal of Korean Society on Water Environment
• /
• v.26 no.1
• /
• pp.52-60
• /
• 2010

We investigated temporal changes of growth of hydrophytes, aquatic biota and absorption of nutrient depending on planting mat type (synthetic fiber, coconut fiber) of artificial vegetation island (AVI) through pilot test using AVI miniatures in Kyungan Stream area of Lake Paldang. There were not significant differences of the water quality parameters (DO, pH, conductivity, turbidity, temperature), phytoplankton and zooplankton abundance among AVI miniatures and control station. The benthic macroinvertebrates showed most individual numbers in the miniature which was made by synthetic fiber and planted with Phragmites australis. The average and maximum height of hydrophytes in AVI miniatures was similar except one miniature where Phragmites australis was planted in synthetic fiber mat and grew more slowly. The adsorbed amount of nutrients and microbes in coconut fiber mat were larger than those in synthetic fiber mat regardless of trophic state of installed waterbody. The continuous increase of adsorbed amount of nutrients and microbes of coconut fiber mat for 8 months in an oligotrophic lake indicates that coconut fiber mat is suitable for the planting mat of AVI in an oligotrophic lake where nutrients are limited for growth of hydrophytes.

• Earthquakes and Structures
• /
• v.19 no.4
• /
• pp.303-313
• /
• 2020

Spacious experimental and numerical investigation has been conducted by researchers to increase the ductility and energy dissipation of concentrically braced frames. One of the most widely used strategies for increasing ductility and energy dissiption, is the use of energy-absorbing systems. In this regard, the cyclic behavior of a chevron bracing frame system equipped with multi-pipe dampers (CBF-MPD) was investigated through finite element method. The purpose of this study was to evaluate and improve the behavior of the CBF using MPDs. Three-dimensional models of the chevron brace frame were developed via nonlinear finite element method using ABAQUS software. Finite element models included the chevron brace frame and the chevron brace frame equipped with multi-pipe dampers. The chevron brace frame model was selected as the base model for comparing and evaluating the effects of multi-tube dampers. Finite element models were then analyzed under cyclic loading and nonlinear static methods. Validation of the results of the finite element method was performed against the test results. In parametric studies, the influence of the diameter parameter to the thickness (D/t) ratio of the pipe dampers was investigated. The results indicated that the shear capacity of the pipe damper has a significant influence on determining the bracing behavior. Also, the results show that the corresponding displacement with the maximum force in the CBF-MPD compared to the CBF, increased by an average of 2.72 equal. Also, the proper choice for the dimensions of the pipe dampers increased the ductility and energy absorption of the chevron brace frame.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.35 no.2
• /
• pp.218-229
• /
• 2011

Dyeing properties of cotton and ramie fabrics with pine needles colorants were studied by investigating the analysis of pine needles colorants, the effect of dyeing conditions (such as dye concentration, dyeing temperatures and times on dye uptakes), effect of mordants, and color change. The various colorfastness of dyed fabrics were evaluated for practical use; in addition, the antimicrobial ability, ultraviolet-cut ability, and deodorant ability were estimated. In the UV-Visible spectrum, the wavelength of the maximum absorption for pine needles extract was 285nm, and pine needles colorants produced a yellow color. From FT-IR and GC-MS results, it was assumed that chromophoric substance from pine needles extracts were mixed with flavonol tannin and flavanol tannin. An increased dyeing concentration resulted in a larger dye uptake and a Freundlich absorption isotherm was obtained. A larger dye uptake occurred as the dyeing time and temperature increased. Post-mordanting was more effective than pre-mordanting and the dye uptake of fabrics improved by mordanting. The colorfastness of dyed fabrics showed a low rating; however, colorfastness to washing and dry cleaning of cotton fabrics mordanted with N.Cu, and friction fastness of ramie fabric mordanted with Cu improved. The dyed fabrics showed very good antimicrobial abilities of 99.9%. In addition, the ultraviolet-cut ability and deodorant ability improved in fabrics dyed with pine needles extracts.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.35 no.2
• /
• pp.206-217
• /
• 2011

The dyeing properties of cotton fabrics with bamboo colorants were studied by investigating the analysis of bamboo colorants, the effect of dyeing conditions (dye concentrations, dyeing temperatures and times on dye uptakes), effect of mordants, and color change. The various colorfastness of dyed fabrics were evaluated for practical use; in addition, the antimicrobial ability, ultraviolet-cut ability, and deodorant ability were also estimated. In the UV-Visible spectrum, the wavelength of the maximum absorption for bamboo stems and leaves extracts was found to be 280nm and 295nm, respectively; in addition, bamboo colorants produced a yellow color. From the FT-IR and GC-MS results, it was assumed that the chromophoric substance from bamboo extracts was composed of flavones substances with tricin. An increased dyeing concentration resulted in a larger dye uptake and a Freundlich absorption isotherm was obtained. A larger dye uptake occurred as the dyeing time and temperature increased. The post-mordanting was more effective than pre-mordanting. Mordants, Fe and N.Fe, were effective for an increased dye uptake. The color of fabrics mordanted with Cu and N.Cu changed to GY. Regardless of mordanting, the colorfastness on the washing of dyed fabrics showed a low rating compared to other fastness. Mordanting adversely affected the lightfastness of dyed fabric. The dyed fabric showed very good antimicrobial abilities of 99.9%. In addition, the ultraviolet-cut ability and deodorant ability improved in cotton fabric dyed with bamboo extracts.